Interface strength effects on the compressive-flexural/shear failure mode transition of composites subjected to four-point bending
Bibliographic record
Abstract
No abstract is available for this record. The assistant can identify its topic from the title, but cannot infer the study’s results.
Source: Not provided · Quality: missing
Research context
OpenAlex topics: Mechanical Behavior of Composites · Advanced MEMS and NEMS Technologies · Structural Analysis and Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. A. S. D. Wang, ASME Paper No. 78-WA/Aero-1 (1978).
2. C. E. Browning, F. L. Abrams andJ. M. Whitney, in ASTM STP 797 (1983) p. 54.
3. C. Shih, PhD thesis, Case Western Reserve University, Cleveland, Ohio (1985).
4. H. C. Kim, PhD thesis, Case Western Reserve University, Cleveland, Ohio (1978).
5. M. H. Telich, MS thesis, Case Western Reserve University, Cleveland, Ohio (1980).
6. M. Davidovitz, A. Mittelman, I. Roman andG. Marom,J. Mater. Sci. 19 (1984) 377.10.1007/BF02403223 ↗
7. P. Yeung andL. J. Broutman, in SPI RP/C 32nd Annual Technical Conference (The Society of the Plastics Industry, New York, 1977) Section 9-B.
8. N. L. Hancox,J. Mater. Sci. 7 (1972) 1030.10.1007/BF00550067 ↗
9. L. G. Bevan,Composites 8 (1977) 227.10.1016/0010-4361(77)90107-0 ↗
10. L. B. Greszezuk, “Microbuckling of Unidirectional Composites”, AFML-TR-71-231.
11. S. W. Tsai andH. T. Hahn, in “Introduction to Composite Materials” (Technomic Publishing, Westport, CT, 1980) pp. 416–18.
12. J. G. Davis, “Compressive Strength of Fibre-reinforced Composite Materials”, in ASTM STP 580 (American Society for Testing and Materials, Philadelphia, Pennsylvania, 1975) p. 364.
13. D. L. Harrod andR. T. Begley, in SAMPE, Vol. 10 (Society of Aerospace Material and Process Engineers, CA, 1966) p. E-1.
14. J. G. Davis, “Compressive Instability and Strength of Uniaxial Filament-reinforced Epoxy Tubes”, NASA-TN-D569 (1970).
15. Catalog and technical information on XU235 and XU205 (Ciba-Geigy Corporation, Ardsley, NY, 1982).
16. D. F. Solnik, PhD thesis, Case Western Reserve University, Cleveland, Ohio (1985).
17. H. C. Kim andL. J. Ebert,J. Compos. Mater. 12 (1978) 139.10.1177/002199837801200203 ↗
18. A. K. Jain, MS thesis, Case Western Reserve University, Cleveland, Ohio (1981).
19. ASTM D 2584-68, “Standard Test Methods for Ignition Loss of Cured Reinforced Resins”.
20. T. C. Kosky, D. K. Banerjee andP. N. Govindarajan, in SPI RP/C 29th Annual Technical Conference (The Society of the Plastics Industry, Inc., New York, 1974) Section 2-B.
21. E. P. Plueddemann, in “Silane Coupling Agents” (Plenum Press, New York, 1982) p. 14.10.1007/978-1-4899-0342-6 ↗
22. W. D. McNeil, B. Bennett andR. I. Leininger, in SPI RP 19th Annual Technical and Management Conference (The Society of the Plastics Industry, New York, 1964) Section 11-B.
23. J. Delmonte andE. Barna, in SPI RP 18th Annual Technical and Management Conference (The Society of the Plastics Industry, New York, 1963) Section 20-A.
24. M. K. Antoon, PhD thesis, Case Western Reserve University, Cleveland, Ohio (1980).
25. R. E. Trabocco andM. Stander, in ASTM STP 602 (American Society for Testing and Materials, Philadelphia, Pennsylvania, 1975).
26. C. E. Browning andJ. M. Whitney, in “Fillers and Reinforcements for Plastics”, edited by R. D. Deanin and N. R. Schott (Adv. Chem. Ser. No. 134, ACS, Washington, DC, 1974) Ch. 14.
27. R. Deiasi andJ. B. Whiteside, in ASTM STP 658 (1978) p. 2.
28. C. E. Browning, in SPI RP/C 28th Annual Technical Conference (The Society of the Plastics Industry, New York, 1973) Section 15-A.
29. C. E. Browning andJ. T. Hartness, in ASTM STP 546 (1975) p. 284.
30. D. A. Scola, in SPI RP/C 30th Annual Technical Conference (The Society of the Plastics Industry, New York, 1975) Section 22-C.
31. T. Suzuki,Reinforced Plastics (Jpn.) 18 (1972) 331.
32. K. Endo andS. Ishihara,J. Soc. Mater. Sci. (Jpn.) 15 (1966) 561.10.2472/jsms.15.561 ↗
33. B. D. Agarwal andL. J. Broutman, in “Analysis and Performance of Fiber Composites” (Wiley, New York, 1980).
34. P. Yeung andL. J. Broutman,Polym. Eng. Sci. 18 (1978) 62.10.1002/pen.760180203 ↗
35. ASTM D 790-84, “Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials” (American Society for Testing and Materials, Philadelphia, Pennsylvania, 1984).
36. ASTM D 2344-76, “Standard Test Method for Apparent Interlaminar Shear Strength of Parallel Fiber Composites by Short-Beam Method” (American Society for Testing and Materials, Philadelphia, Pennsylvania, 1984).