Properties of bonded-polypropylene-bead foams: data and modelling
Source abstract
Abstract
Various mechanical properties (uniaxial compression, Poisson's ratio, indentation resistance) were measured for both expanded polypropylene (EPP) foam and bonded-polypropylene-bead foam. Finite Element Analysis, used on Body Centred Cubic (BCC) lattice models of uniform sized beads, predicted that the compressive response of EPP was hardly affected by the small volume fraction of inter-bead channels, whereas the bonded-bead foam with 25% porosity should have a near-linear compressive impact response. The foam lateral expansion on compression was predicted to be less than 3.5%, which was confirmed by experiment. Computational Fluid Dynamics was used to predict the air permeability of the models. An overlapping sphere model confirmed an earlier analysis, whereas a wet Kelvin foam model gave slightly lower permeabilities. The permeability increases with the square of the bead diameter and with the 2.6th power of the porosity.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Polymer Foaming and Composites · Asphalt Pavement Performance Evaluation · Rheology and Fluid Dynamics Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. Svec P, Rosik L, Horak Z (1990) Styrene based plastics and their modification. Ellis Horwood, London
2. Skinner SJ, Baxter S, Eagleton SD, (1965) Plast Eng 42:171
3. Mills NJ (1997) Cell Polym 16:19410.1177/0262489319971603003 ↗
4. Beverte I (2004) J Cell Plast 40:19110.1177/0021955X04043718 ↗
5. Ibba A, Avalle M (2003) Identificazione di schiume in polipropilene e relazione tra densita e parametric dei modelli, www.pcm.unifi.it/lavorasalerno/ART_056.pdf (AIAS Congress, Salerno)
6. Zohdi TI (2003) Proc Roy Soc 459A:139510.1098/rspa.2003.1117 ↗
7. Mills NJ (2004) Polyolefin foams, RAPRA review report 167 (vol 14, no 11) ISBN 1-85957-434-3, 136 pp
8. Mills NJ (2005) J Mater Sci 40:584510.1007/s10853-005-5018-5 ↗
9. Hill RG, Koch DL, Ladd AJC (2001) J Fluid Mech 448:24310.1017/S0022112001005936 ↗
10. Larson RE, Higdon JJL (1988) Phys Fluids A1:38
11. Bainbridge DW, Nickerson LP, Denton GC (2002) US Patent 6,453,477 Protective padding for sports gear
12. Mills NJ (1994) In: Hilyard NC, Cunningham A (eds) Low density cellular plastics, Chapman & Hall, 270–31810.1007/978-94-011-1256-7_9 ↗
13. Mills NJ (2005) Plastics: microstructure and engineering applications, 3rd edn Butterworth Heinemann, p 126
14. Mills NJ, Gilchrist A (2000) Cell Polymer 19:389
15. Mills NJ, Gilchrist A (2005) Dynamic FEA of bicycle helmet oblique impact, submitted to Int J Impact Eng
16. Surface Evolver (2004) at //www.susqu.edu/facstaff/b/brakke/evolver/
17. Mills NJ (2007) Int J Solids Struct 44:5110.1016/j.ijsolstr.2006.04.014 ↗
18. Masso-Moreu Y, Mills NJ (2003) Int J Impact Eng 28:65310.1016/S0734-743X(02)00148-3 ↗
19. Fluent Manual, Fluent Inc, Lebanon, USA
20. Zhu H, Mills NJ, Knott JF (1997) J Mech Phys Solids 45:187510.1016/S0022-5096(97)00027-6 ↗
21. Avalle M, Belingardi G, Montanini R (2001) Int J Impact Eng 25:45510.1016/S0734-743X(00)00060-9 ↗