journal article·2024-11Open access

Diffusion bonding of steels with a homogeneous microstructure throughout the joint

Nicolás Di Luozzo, Michael Schulz, Michel Boudard, Silvina Limandri, Gastón Garbarino, Marcelo Fontana

Journal of Materials Science· Volume 59· Issue 43

Abstract

Cold-finished carbon steel bars were bonded by means of the transient liquid phase bonding (TLPB) process using amorphous metallic foils of the eutectic Fe-B composition as filler material. A homogeneous microstructure throughout the joint was obtained. Traces of borides in the middle of the joint were the only distinguishable microconstituent from the base metal due to the TLPB process.The B concentration profile across the joint was measured by neutron radiography and was found to be composed of a central sharp peak with a maximum concentration of 15.9 ppm B superimposed over a broad peak (base width of ≈ 5 mm) with a maximum concentration of 13.3 ppm B. Owing to this low range of B concentrations, boride precipitation was almost suppressed, and only a scarce number of borides were observed at the joint.The resulting boride structure was identified as Fe23B6 by synchrotron microfocused X-ray diffraction, and its stabilization at room temperature is discussed.The bonded samples were subjected to a bend test, with a bending angle of 180°, and no cracks were observed. In tension tests, the bonded samples attained an ultimate tensile strength (UTS) of 434 MPa, an elongation of 32.3% and a reduction area q of 51.2% - 78.6%, 165.6% and 75.4%, respectively, of the base metal. The fracture of the bonded samples occurred at the joint. It was determined that the decrease in UTS compared with that of the base metal was due to the recovery, recrystallization and grain growth that occurred during the TLPB thermal cycle. In addition, from fracture surface observation, it was found that the decrease in q in bonded samples was caused by the presence of traces of borides at the joint, which were the result of the liquid phase that solidified during the cooling stage.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · X-ray Diffraction in Crystallography · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. American Welding Society (2007) Brazing Handbook, 5th edn. American Welding Society, Miami
2. International Organization for Standardization (2016) ISO 17672:2016 Brazing Filler metals. https://www.iso.org/standard/63627.html. Accessed 4 Mar 2024
3. Xie C, Deng K, Teng J et al (2023) Microstructural evolution and mechanical properties of Ni-based superalloy joints brazed using a ternary Ni-W-B amorphous brazing filler metal. J Alloys Compd 960:170663. https://doi.org/10.1016/j.jallcom.2023.17066310.1016/j.jallcom.2023.170663 ↗
4. Li S, Peng Y, Du Y et al (2022) Microstructural characteristics and mechanical properties of IC10 superalloy and (CoCrNi)94Al3Ti3 MEA joint brazed using NiCrSiB filler. Mater Charact 189:111964. https://doi.org/10.1016/j.matchar.2022.11196410.1016/j.matchar.2022.111964 ↗
5. Li G, Zhang P, Shi H, Yu Z (2018) Microstructure and properties of Cr18-Ni8 steel joints brazed with BNi7+3%Cu composite solder. Vacuum 148:303–311. https://doi.org/10.1016/j.vacuum.2017.12.00110.1016/j.vacuum.2017.12.001 ↗
6. Duvall DS, Owczarski WA, Paulonis DF (1974) TLP bonding: a new method for joining heat resistant alloys. Weld J 53:203–214
7. Tuah-Poku I, Dollar M, Massalski TB (1988) A study of the transient liquid phase bonding process applied to a Ag/Cu/Ag sandwich joint. Metall Trans A 19:675–686. https://doi.org/10.1007/BF0264928210.1007/BF02649282 ↗
8. Di Luozzo N, Boudard M, Fontana M (2019) Transient liquid phase bonding of carbon steel components using Ni-based foils—a comprehensive joint characterization. Mater Sci Eng, A 751:51–61. https://doi.org/10.1016/j.msea.2019.02.05010.1016/j.msea.2019.02.050 ↗
9. Wang X, Li X, Wang C (2013) Effect of two-step heating process on joint microstructure and properties during transient liquid phase bonding of dissimilar materials. Mater Sci Eng, A 560:711–716. https://doi.org/10.1016/j.msea.2012.10.01810.1016/j.msea.2012.10.018 ↗
10. Totten GE (2006) Steel Heat Treatment: Metallurgy and Technologies, 2nd edn. Taylor & Francis Group, Boca Raton10.1201/NOF0849384530 ↗
11. Di Luozzo N, Doisneau B, Boudard M et al (2014) Microstructural and mechanical characterizations of steel tubes joined by transient liquid phase bonding using an amorphous Fe–B–Si interlayer. J Alloys Compd 615:S18–S22. https://doi.org/10.1016/j.jallcom.2013.11.16110.1016/j.jallcom.2013.11.161 ↗
12. Li W, Li X, Liu Y et al (2020) Homogenization stage during TLP bonding of RAFM steel with a Fe–Si–B interlayer: microstructure evolution and mechanical properties. Mater Sci Eng, A 780:139205. https://doi.org/10.1016/j.msea.2020.13920510.1016/j.msea.2020.139205 ↗
13. Bhadeshia H, Honeycombe R (2017) Solutes that Substitute for Iron. In: Bhadeshia H, Honeycombe R (eds) Steels: microstructure and properties, 4th edn. Butterworth-Heinemann, Kidlington, pp 101–13410.1016/B978-0-08-100270-4.00004-4 ↗
14. Naz GJ, Dong D, Geng Y et al (2017) Composition formulas of Fe-based transition metals-metalloid bulk metallic glasses derived from dual-cluster model of binary eutectics. Sci Rep 7:9150. https://doi.org/10.1038/s41598-017-09100-910.1038/s41598-017-09100-9 ↗
15. Burrier H (2013) Steel heat treating fundamentals and processes. In: Dossett JL, Totten GE (eds) ASM Handbook, vol 4A. Steel Heat Treating. Fundamentals and Processes. ASM International, Materials Park, pp 26–59
16. International Organization for Standardization (2016) ISO 683–2:2016 Heat-treatable steels, alloy steels and free-cutting steels. Part 2: Alloy steels for quenching and tempering. https://www.iso.org/standard/70643.html. Accessed 4 Mar 2024
17. Di Luozzo N, Fontana M, Arcondo B (2008) Transient liquid phase bonding of steel using an Fe–B interlayer: microstructural analysis. J Mater Sci 43:4938–4944. https://doi.org/10.1007/s10853-008-2720-010.1007/s10853-008-2720-0 ↗
18. Di Luozzo N, Schulz M, Fontana M (2020) Imaging of boron distribution in steel with neutron radiography and tomography. J Mater Sci 55:7927–7937. https://doi.org/10.1007/s10853-020-04556-z10.1007/s10853-020-04556-z ↗
19. ASTM A108-18 (2018) Standard specification for steel bar, Carbon and Alloy, Cold-Finished https://doi.org/10.1520/A0108-1810.1520/A0108-18 ↗
20. Di Luozzo N, Boudard M, Fontana M, Arcondo B (2016) Effective diffusion coefficient for Cu in steel joined by transient liquid phase bonding. Mater Des 92:760–766. https://doi.org/10.1016/j.matdes.2015.12.10110.1016/j.matdes.2015.12.101 ↗
21. Hielscher R, Silbermann CB, Schmidl E, Ihlemann J (2019) Denoising of crystal orientation maps. J Appl Crystallogr 52:984–996. https://doi.org/10.1107/S160057671900907510.1107/S1600576719009075 ↗
22. Calzada E, Gruenauer F, Mühlbauer M et al (2009) New design for the ANTARES-II facility for neutron imaging at FRM II. Nucl Instrum Methods Phys Res A 605:50–53. https://doi.org/10.1016/j.nima.2009.01.19210.1016/j.nima.2009.01.192 ↗
23. International Organization for Standardization (2013) ISO 898–1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs with specified property classes. Coarse thread and fine pitch thread. https://www.iso.org/standard/60610.html. Accessed 4 Mar 2024
24. Dianoux A-J, Lander G (2003) Institut Laue-Langevin Neutron Data Booklet, 2nd edn. Old City Publishing, Grenoble
25. Jackson DF, Hawkes DJ (1981) X-ray attenuation coefficients of elements and mixtures. Phys Rep 70:169–233. https://doi.org/10.1016/0370-1573(81)90014-410.1016/0370-1573(81)90014-4 ↗
26. Mezouar M, Crichton WA, Bauchau S et al (2005) Development of a new state-of-the-art beamline optimized for monochromatic single-crystal and powder X-ray diffraction under extreme conditions at the ESRF. J Synchrotron Radiat 12:659–664. https://doi.org/10.1107/S090904950502321610.1107/S0909049505023216 ↗
27. Black DR, Windover D, Henins A et al (2011) Certification of standard reference material 660B. Powder Diffr 26:155–158. https://doi.org/10.1154/1.359106410.1154/1.3591064 ↗
28. Prescher C, Prakapenka VB (2015) DIOPTAS: a program for reduction of two-dimensional X-ray diffraction data and data exploration. High Press Res 35:223–230. https://doi.org/10.1080/08957959.2015.105983510.1080/08957959.2015.1059835 ↗
29. Kieffer J, Valls V, Blanc N, Hennig C (2020) New tools for calibrating diffraction setups. J Synchrotron Radiat 27:558–566. https://doi.org/10.1107/S160057752000077610.1107/S1600577520000776 ↗
30. Toby BH, Von Dreele RB (2013) GSAS-II : the genesis of a modern open-source all purpose crystallography software package. J Appl Crystallogr 46:544–549. https://doi.org/10.1107/S002188981300353110.1107/S0021889813003531 ↗
31. ASTM E8/E8M-22 (2022) Standard Test Methods for Tension Testing of Metallic Materials. https://doi.org/10.1520/E0008_E0008M-2210.1520/E0008_E0008M-22 ↗
32. International Organization for Standardization (2023) ISO 5173:2023 Destructive tests on welds in metallic materials. Bend tests. https://www.iso.org/standard/81724.html. Accessed 4 Mar 2023
33. ASTM E112–13 (2021) Standard Test Methods for Determining Average Grain Size. https://doi.org/10.1520/E0112-13R2110.1520/E0112-13R21 ↗
34. Llovet X, Moy A, Pinard PT, Fournelle JH (2021) Reprint of: Electron probe microanalysis: a review of recent developments and applications in materials science and engineering. Prog Mater Sci 120:100818. https://doi.org/10.1016/j.pmatsci.2021.10081810.1016/j.pmatsci.2021.100818 ↗
35. Portebois L, Mathieu S, Bouizi Y et al (2014) Effect of boron addition on the oxidation resistance of silicide protective coatings: a focus on boron location in as-coated and oxidised coated niobium alloys. Surf Coat Technol 253:292–299. https://doi.org/10.1016/j.surfcoat.2014.05.05810.1016/j.surfcoat.2014.05.058 ↗
36. Kolmogorov AN, Shah S, Margine ER et al (2010) New superconducting and semiconducting fe-b compounds predicted with an Ab initio evolutionary search. Phys Rev Lett 105:217003. https://doi.org/10.1103/PhysRevLett.105.21700310.1103/PhysRevLett.105.217003 ↗
37. Taylor KA, Hansen SS (1990) The boron hardenability effect in thermomechanically processed, direct-quenched 0.2 Pct C steels. Metall Trans A 21:1697–1708. https://doi.org/10.1007/BF0267258610.1007/BF02672586 ↗
38. Hara T, Asahi H, Uemori R, Tamehiro H (2004) Role of combined addition of niobium and boron and of molybdenum and boron on hardnenability in low carbon steels. ISIJ Int 44:1431–1440. https://doi.org/10.2355/isijinternational.44.143110.2355/isijinternational.44.1431 ↗
39. Drillet J, Valle N, Iung T (2012) Nanometric scale investigation of phase transformations in advanced steels for automotive application. Metall and Mater Trans A 43:4947–4956. https://doi.org/10.1007/s11661-012-1218-110.1007/s11661-012-1218-1 ↗
40. Da Rosa G, Maugis P, Portavoce A et al (2020) Grain-boundary segregation of boron in high-strength steel studied by nano-SIMS and atom probe tomography. Acta Mater 182:226–234. https://doi.org/10.1016/j.actamat.2019.10.02910.1016/j.actamat.2019.10.029 ↗
41. Prithiv TS, Gault B, Li Y et al (2023) Austenite grain boundary segregation and precipitation of boron in low-C steels and their role on the heterogeneous nucleation of ferrite. Acta Mater 252:118947. https://doi.org/10.1016/j.actamat.2023.11894710.1016/j.actamat.2023.118947 ↗
42. Da Rosa G, Maugis P, Portavoce A et al (2023) Boron segregation at austenite grain boundaries: an equilibrium phenomenon. Acta Mater 255:119098. https://doi.org/10.1016/j.actamat.2023.11909810.1016/j.actamat.2023.119098 ↗
43. Fujishiro T, Hara T, Shigesato G (2015) Effect of Mo on γ to α transformation and precipitation behavior in B-added steel. Tetsu-to-Hagane 101:300–307. https://doi.org/10.2355/tetsutohagane.101.30010.2355/tetsutohagane.101.300 ↗
44. American Petroleum Institute (API) (2021) API STANDARD 1104Welding of Pipelines and Related Facilities 22nd Edition. American Petroleum Institute
45. SAE J1397_202403 (2024) Estimated Mechanical Properties and Machinability of Steel Bars. https://doi.org/10.4271/J1397_20240310.4271/J1397_202403 ↗