journal article·2021-08

Cryogenic stability of retained austenite in Fe–Cr–Ni weld metals obtained by laser welding

Dongqun Xin, Shun Lu, Yan Cai, Xueming Hua

Journal of Materials Science· Volume 56· Issue 24
Publisher page

Abstract

Fe–Cr–Ni alloy is the most potential substitute for Ni-based alloys as consumable in low-temperature nickel steel welding. In this study, six groups of Fe–Cr–Ni weld metals with different chemical composition were fabricated by single-pass laser welding. The volume fraction of retained austenite (RA) in the weld metals in as-welded condition increased from 0 to 30.2% with the increment of amounts of alloy elements (Cr, Ni and Mn). The thermal stability of RA was investigated by deep cryogenic treatment (DCT) to see whether sufficient RA can be maintained at low temperature. The results revealed that if the initial content of RA was < ~ 18%, RA would not transform into martensite after DCT. The surrounding martensite can hinder the transformation of RA, which plays a dominant role in the cryogenic stability of RA. The higher the strength/hardness of the surrounding martensite, the stronger the resistance to the transformation of RA. The carbon content of the surrounding martensite is the crucial factor affecting its strength/hardness. However, if the alloy elements amounts were too large, the thermal stability of RA would decrease and some of RA would transform to martensite after DCT. The newly formed martensite (fresh martensite) increased strain concentration of the weld metal, which enhanced the strain energy of martensite transformation and therefore restrained the further transformation of RA. The content of RA in the Fe-13.497Cr-7.249Ni-0.93Mn and Fe-15.548Cr-7.622Ni-0.961Mn weld metals after DCT dropped to ~ 18%. The optimum of initial content of RA in the weld metals for low-temperature toughness is ~ 18%.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Dhooge A, Provost W, Ostyn K, Vinckier A (1981) Weldability and fracture toughness of 5% Ni steel part 1: weld simulation testing. Welding Research Council Bulletin, pp. 1-10, New York, United States
2. Kamada A, Koshizuka N, Funakoshi T (1974) Electron microscope study of tempered martensite and bainite in 5% Ni-0. 5% Mo steels. Tetsu-to-Hagane 60:372–38510.2355/tetsutohagane1955.60.3_372 ↗
3. Wu Y, Cai Y, Wang H, Shi S, Hua X, Wu Y (2015) Investigation on microstructure and properties of dissimilar joint between SA553 and SUS304 made by laser welding with filler wire. Mater Des 87:567–57810.1016/j.matdes.2015.08.076 ↗
4. Qiu H, Wang LN, Qi JG, Zuo H, Hiraoka K (2013) Enhancement of fracture toughness of high-strength Cr-Ni weld metals by strain-induced martensite transformation. Mater Sci Eng A 579:71–7610.1016/j.msea.2013.05.012 ↗
5. Wu S, Wang D, Di X, Zhang Z, Feng Z, Liu X, Li Y, Meng X (2018) Toughening mechanisms of low transformation temperature deposited metals with martensite-austenite dual phases. J Mater Sci 53:3720–3734. https://doi.org/10.1007/s10853-017-1766-210.1007/s10853-017-1766-2 ↗
6. Wu Y, Cai Y, Sun D, Zhu J, Wu Y (2015) Microstructure and properties of high-power laser welding of SUS304–SA553 for cryogenic applications. J Mater Process Technol 225:56–66. https://doi.org/10.1016/j.jmatprotec.2015.05.01110.1016/j.jmatprotec.2015.05.011 ↗
7. Shen YF, Qiu LN, Sun X, Zuo L, Liaw PK, Raabe D (2015) Effects of retained austenite volume fraction, morphology, and carbon content on strength and ductility of nanostructured TRIP-assisted steels. Mater Sci Eng A 636:551–56410.1016/j.msea.2015.04.030 ↗
8. Xiong XC, Chen B, Huang MX, Wang JF, Wang L (2013) The effect of morphology on the stability of retained austenite in a quenched and partitioned steel. Scr Mater 68:321–32410.1016/j.scriptamat.2012.11.003 ↗
9. Girault E, Mertens A, Jacques P, Houbaert Y, Verlinden B, Van Humbeeck J (2001) Comparison of the effects of silicon and aluminium on the tensile behaviour of multiphase TRIP-assisted steels. Scr Mater 44:885–89210.1016/S1359-6462(00)00697-7 ↗
10. Xin D, Cai Y, Hua X (2020) Pivotal microstructural characteristics to determine the cryogenic impact toughness of dissimilar joint between SA645 and AISI304L made by autogenous fiber laser welding. Mater Charact 165:110399. https://doi.org/10.1016/j.matchar.2020.11039910.1016/j.matchar.2020.110399 ↗
11. Hidalgo J, Findley KO, Santofimia MJ (2017) Thermal and mechanical stability of retained austenite surrounded by martensite with different degrees of tempering. Mater Sci Eng A 690:337–34710.1016/j.msea.2017.03.017 ↗
12. Van Dijk NH, Butt AM, Zhao L, Sietsma J, Offerman SE, Wright JP, Van der Zwaag S (2005) Thermal stability of retained austenite in TRIP steels studied by synchrotron X-ray diffraction during cooling. Acta Mater 53:5439–544710.1016/j.actamat.2005.08.017 ↗
13. Zwaag SVD, Zhao L, Kruijver SO, Sietsma J (2002) Thermal and mechanical stability of retained austenite in aluminum-containing multiphase TRIP steels. ISIJ Int 42:1565–157010.2355/isijinternational.42.1565 ↗
14. Qiu H, Qi JG, Wang LN, Yin FX, Hiraoka K (2013) Thermal stability of retained austenite in Cr-Ni weld metals at low temperatures. Mater Sci Technol 29:594–59710.1179/1743284712Y.0000000194 ↗
15. Wu R, Li W, Wang C, Xiao L, Wang L, Jin X (2015) Stability of retained austenite through a combined intercritical annealing and quenching and partitioning (IAQP) treatment. Acta Metall Sin (Engl Lett) 28:386–39310.1007/s40195-015-0217-9 ↗
16. Sun X, Zhang M, Wang Y, Jiang Y, Song Y, Ge N (2019) Effect of deep cryogenic pretreatment on microstructure and mechanical properties of warm-deformed 7 Mn steel after intercritical annealing. Mater Sci Eng A 764:138202. https://doi.org/10.1016/j.msea.2019.13820210.1016/j.msea.2019.138202 ↗
17. Khodir S, Shibayanagi T, Takahashi M, Abdel-Aleem H, Ikeuchi K (2014) Microstructural evolution and mechanical properties of high strength 3–9% Ni-steel alloys weld metals produced by electron beam welding. Mater Des 60:391–40010.1016/j.matdes.2014.03.056 ↗
18. Malakondaiah G, Srinivas M, Rao PR (1997) Ultrahigh-strength low-alloy steels with enhanced fracture toughness. Prog Mater Sci 42:209–24210.1016/S0079-6425(97)00016-9 ↗
19. Chen X, Fang Y, Li P, Yu Z, Wu X, Li D (2015) Microstructure, residual stress and mechanical properties of a high strength steel weld using low transformation temperature welding wires. Mater Des 65:1214–122110.1016/j.matdes.2014.10.013 ↗
20. Oñoro J (2006) Weld metal microstructure analysis of 9–12% Cr steels. Int J Pressure Vessels Pip 83:540–54510.1016/j.ijpvp.2006.03.005 ↗
21. Wang P, Lu SP, Xiao NM, Li DZ, Li YY (2010) Effect of delta ferrite on impact properties of low carbon 13Cr-4Ni martensitic stainless steel. Mater Sci Eng A 527:3210–321610.1016/j.msea.2010.01.085 ↗
22. Manugula VL, Rajulapati KV, Reddy GM, Rao KBS (2017) Role of evolving microstructure on the mechanical properties of electron beam welded ferritic-martensitic steel in the as-welded and post weld heat-treated states. Mater Sci Eng A 698:36–4510.1016/j.msea.2017.05.036 ↗
23. Li L, Li W, Min N, Liu W, Zhang C, Jin X (2020) Mechanical response of a medium manganese steel with encapsulated austenite. Scr Mater 178:211–21710.1016/j.scriptamat.2019.11.033 ↗
24. Hsu TY (1995) Carbon diffusion and kinetics during the lath martensite formation. J Phys IV Proc 05:351–354
25. Sun C, Liu SL, Misra RDK, Li Q, Li DH (2018) Influence of intercritical tempering temperature on impact toughness of a quenched and tempered medium-Mn steel: Intercritical tempering versus traditional tempering. Mater Sci Eng A 711:484–49110.1016/j.msea.2017.11.072 ↗
26. Talaş S (2010) The assessment of carbon equivalent formulas in predicting the properties of steel weld metals. Mater Des 31:2649–265310.1016/j.matdes.2009.11.066 ↗
27. Zhou Z, Di X, Li C, Wu S (2020) Effect of restraint stress on martensite transformation in low transformation temperature weld metal. J Mater Sci 55:2202–2214. https://doi.org/10.1007/s10853-019-04049-810.1007/s10853-019-04049-8 ↗
28. Fisher JC (1949) Technical notes-measurement of interfacial tensions. Trans Metall Soc AIME 185:688
29. Zhu N, Wu Q, He Y, Lu X, Lin L, Hu P (2014) Effect of Ni on the stability of retained austenite and mechanical properties for TRIP steels containing vanadium. Steel Res Int 85:143–15410.1002/srin.201300098 ↗
30. De Sanctis M, Lovicu G, Valentini R, Dimatteo A, Ishak R, Migliaccio U, Montanari R, Pietrangeli E (2015) Microstructural features affecting tempering behavior of 16Cr-5Ni supermartensitic steel. Metall Mater Trans A 46:1878–188710.1007/s11661-015-2811-x ↗
31. Wu S, Wang D, Di X, Li C, Zhang Z, Zhou Z, Liu X (2019) Strength-toughness improvement of martensite-austenite dual phase deposited metals after austenite reversed treatment with short holding time. Mater Sci Eng A 755:57–6510.1016/j.msea.2019.03.125 ↗
32. Hsu TY (1985) An approximate approach for the calculation of Ms in iron-base alloys. J Mater Sci 20(1):23–3110.1007/BF00555894 ↗
33. Hutchinson B, Hagström J, Karlsson O, Lindell D, Tornberg M, Lindberg F, Thuvander M (2011) Microstructures and hardness of as-quenched martensites (0.1–0.5%C). Acta Mater 59:5845–585810.1016/j.actamat.2011.05.061 ↗
34. Luo ZC, Huang MX (2020) The role of interstitial carbon atoms on the strain-hardening rate of twinning-induced plasticity steels. Scr Mater 178:264–26810.1016/j.scriptamat.2019.11.047 ↗
35. Calcagnotto M, Ponge D, Demir E, Raabe D (2010) Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD. Mater Sci Eng A 527:2738–274610.1016/j.msea.2010.01.004 ↗
36. Morito S, Yoshida H, Maki T, Huang X (2006) Effect of block size on the strength of lath martensite in low carbon steels. Mater Sci Eng A 438–440:237–24010.1016/j.msea.2005.12.048 ↗