journal article·2010-08

The influence of salt fog exposure on the fatigue performance of Alclad 6xxx aluminum alloys laser beam welded joints

A. T. Kermanidis, A. D. Zervaki, G. N. Haidemenopoulos, Sp. G. Pantelakis

Journal of Materials Science· Volume 45· Issue 16
Publisher page

Abstract

Laser welding is increasingly used for the fabrication of lightweight and cost-effective integral stiff- ened panels in modern civil aircraft. As these structures age in service, the issue of the effect of corrosion on their damage tolerance requires attention. In this work, labora- tory data on the influence of salt fog corrosion on the fatigue behavior of cladded 6156 T4 aluminum alloy laser welded specimens are presented. The experimental inves- tigation was performed on 6156 T4 laser butt welded sheets. Prior to fatigue testing the welded joints were exposed to laboratory salt fog corrosion exposure for 720 h. The results showed that the clad layer offers suffi- cient corrosion protection both on base metal and the weld. Fatigue testing was followed by standard metallographic analysis in order to identify fatigue crack initiation sites. Crack initiation is located in all welded samples near the weld reinforcement which induces a significant stress concentration. Localized corrosion attack of the clad layer, in the form of pitting corrosion, creates an additional stress concentration which accelerates crack initiation leading to shorter fatigue life relative to the uncorroded samples. The potency of small corrosion pits to act as stress concentra- tion sites has been assessed analytically. The above results indicate that despite the general corrosion protection offered by the clad layer, the localized attack described above leads to inferior fatigue performance, a fact that should be taken under consideration in the design and maintenance of these structures.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fatigue and fracture mechanics · Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Kermanidis AT, Zervaki AD, Haidemenopoulos GN, Pantelakis SpG (2010) Mater Des 31:4210.1016/j.matdes.2009.07.020 ↗
2. Zhang Da-Q, Li J, Joo H, Lee K (2009) Corros Sci 51:139910.1016/j.corsci.2009.03.030 ↗
3. Petroyiannis PV, Pantelakis SpG, Haidemenopoulos GN (2005) Theor Appl Fract Mech 44:7010.1016/j.tafmec.2005.05.006 ↗
4. Velterop L (18–22 May 2003) Phosphoric sulphuric acid anodising: an alternative for chromic acid anodising in aerospace applications? NLR Report,NLR-TP-2003-210. National Aerospace Laboratory NLR, Structures Technology Department, Aluminum Surface Science and Technology, in Bonn, Germany
5. Davis JR (ed) (1993) ASM speciality handbook: aluminum and aluminum alloys. ASM International, OH, USA
6. Simulation Based Corrosion Management (SICOM) EU funded Project, FP6 Contract No. 030804, 2007–2010
7. Karlashov AV, Tokarev VP, Batov AP (1965) Fiziko-chimicheskaya Mekhanika Materialov 1(6):707
8. Genkin JM (1996) PhD thesis, Department of Materials Science and Engineering, Massachusetts Institute of Technology
9. Duquesnay DL, Underhill PR, Britt HJ (2005) Fatigue Fract Eng Mater Struct 28:38110.1111/j.1460-2695.2005.00869.x ↗
10. Merati A (2005) Int J Fatigue 27:3310.1016/j.ijfatigue.2004.06.010 ↗
11. Bray GH et al (1997) In: Van Der Sluys WA, Piascik RS, Zawierucha R (eds) Effects of the environment on the initiation of crack growth ASTM STP 1298. American Society for Testing and Materials, PA, USA, pp 89–10310.1520/STP19955S ↗
12. Chubb JP, Morad TA, Hockenhull BS, Bristow JW (1995) Int J Fatigue 17(1):4910.1016/0142-1123(95)93050-C ↗
13. Kermanidis AT, Petroyiannis PV, Pantelakis SpG (2005) Theor Appl Fract Mech 43:12110.1016/j.tafmec.2004.12.008 ↗
14. Wang QY, Kawagoishi N, Chen Q (2003) Scripta Mater 49:71110.1016/S1359-6462(03)00365-8 ↗
15. Jones K, Hoeppner DW (2006) Corros Sci 48:310910.1016/j.corsci.2005.11.008 ↗
16. ASTM E466-82 (1994) Annual book of ASTM standards, metals—test methods and analytical procedures, Section 3, vol 03.01, Metals-mechanical testing; elevated low-temperature tests; metallography. ASTM, PA, USA
17. ASTM Β117-94 (1995) Annual book of ASTM standards, metals—test methods and analytical procedures, section 3, vol 03.02, wear and erosion; metal corrosion. ASTM, PA, USA
18. ASTM G1-90 (2000) Standard practice for preparing, cleaning, and evaluating corrosion test specimens. American Society for Testing and Materials, PA, USA
19. Zervaki AD, Haidemenopoulos GN (2007) Weld J 86:211
20. Masubuchi K (1980) Analysis of welded structures. Pergamon, Elmsford, NY
21. Brandt U, Lehrke H-P, Sonsino CM, Radaj D (1999) Anwendung des Kergrundkonzeptes für die schwingfeste Bemessung von Schweißverbindungen aus Aluminumknetlegierungen. Fraunhofer-Institut fuer Betriebsfestigkeit (LBF), Darmstadt (Final-Report)
22. Lehrke H-P (1999) Berechnung von formzahlen fuer Schweißverbindungen Konstruktion 51(1/2):47
23. Ushirokawa O, Nakayama E (1983) Stress concentration factor at welded joints. Ishikawaj ima-Harima Gihou (Technical Report) 23(4) (in Japanese)
24. Cole AG, Brown AFC (1958) J R Aeronaut Soc 62:59710.1017/S0368393100069339 ↗
25. Petroyiannis PV, Kermanidis AlTh, Kamoutsi E, Pantelakis SpG, Bontozoglou V, Haidemenopoulos GN (2005) Fatigue Fract Eng Mater Struct 28:56510.1111/j.1460-2695.2005.00900.x ↗
26. Pantelakis SpG, Haidemenopoulos GN (2002) In: Proceedings of the 4th international conference on new challenges in mesomechanics, Aalborg University, Denmark