journal article·2016-05

The effect of ceramic synthesis conditions on the electrochemical properties of Li2Ti3O7

P. Díaz-Carrasco, P. C. Miscow Ferreira, O. Dolotko, J. C. Pérez-Flores, U. Amador, A. Kuhn, F. García-Alvarado

Journal of Materials Science· Volume 51· Issue 9
Publisher page

Abstract

Different ceramic synthesis conditions of ramsdellite Li2Ti3O7 have been investigated in order to determine the influence on the electrochemical performances as the negative electrode of lithium-ion batteries. Lithium source, thermal pretreatment, synthesis temperature, and time of reactions were the analyzed conditions. A convenient and cheap reagent like Li2CO3 treated with TiO2 at high temperature (1250 °C) for very short time (2 h) provides a reliable active material. When tested versus lithium, the initial specific capacity (150 mAh g−1) is lower than that of ceramic samples prepared at lower temperature or for longer treatment times (ca. 170 mAh g−1). The lower initial capacity is attributed to the large particle size obtained at high temperature. However, advantageously the capacity retention of the former is superior. Thus, 115 mAh g−1 at C/20 rate is fairly kept (77 % retention) after 100 cycles. The better cyclability of samples prepared at high temperature (with large particle size) is likely due to lower surface reactivity that compensates the lower initial discharge capacity when cycling. A compromise between high initial capacity and capacity retention must be reached when using Li2Ti3O7 as a battery electrode. The good behavior of the optimized material is shown by testing it against commercial LiCoO2 as the positive electrode. The high capacity (ca. 135 mAh g−1) and outstanding cyclability observed prove that optimized ramsdellite may be effectively used as a long-life negative electrode material.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advancements in Battery Materials · Advanced Battery Materials and Technologies · Extraction and Separation Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (55)

Show source-provided references
1. Etacheri V, Marom R, Elazari R, Salitra G, Aurbach D (2011) Challenges in the development of advanced li-ion batteries. Energy Environ Sci 4(9):3243–3262. doi: 10.1039/c1ee01598b10.1039/c1ee01598b ↗
2. Yang ZG, Choi D, Kerisit S, Rosso KM, Wang DH, Zhang J, Graff G, Liu J (2009) Nanostructures and lithium electrochemical reactivity of lithium titanites and titanium oxides: a review. J Power Sources 192(2):588–598. doi: 10.1016/j.jpowsour.2009.02.03810.1016/j.jpowsour.2009.02.038 ↗
3. Ohzuku T, Ueda A, Yamamoto N (1995) Zero-strain insertion material of Li[Li1/3Ti5/3]O4 for rechargeable lithium cells. J Electrochem Soc 142(5):1431–1435. doi: 10.1149/1.204859210.1149/1.2048592 ↗
4. Zhu G-N, Wang Y-G, Xia Y-Y (2012) Ti-based compounds as anode materials for li-ion batteries. Energy Environ Sci 5(5):6652–6667. doi: 10.1039/c2ee03410g10.1039/c2ee03410g ↗
5. Kyeremateng NA (2014) Self-organised TiO2 nanotubes for 2D or 3D li-ion microbatteries. Chemelectrochem 1(9):1442–1466. doi: 10.1002/celc.20140210910.1002/celc.201402109 ↗
6. Aravindan V, Lee Y-S, Madhavi S (2015) Research progress on negative electrodes for practical li-ion batteries: beyond carbonaceous anodes. Adv Energy Mater 5(13). Article: 1402225. doi: 10.1002/aenm.20140222510.1002/aenm.201402225 ↗
7. Yoshio M, Wang HY, Fukuda K, Umeno T, Abe T, Ogumi Z (2004) Improvement of natural graphite as a lithium-ion battery anode material, from raw flake to carbon-coated sphere. J Mater Chem 14(11):1754–1758. doi: 10.1039/b316702j10.1039/b316702j ↗
8. Park K-S, Benayad A, Kang D-J, Doo S-G (2008) Nitridation-driven conductive Li4Ti5O12 for lithium ion batteries. J Am Chem Soc 130(45):14930–14931. doi: 10.1021/ja806104n10.1021/ja806104n ↗
9. Yoshio M, Wang HY, Fukuda K (2003) Spherical carbon-coated natural graphite as a lithium-ion battery-anode material. Angew Chem Int Ed 42(35):4203–4206. doi: 10.1002/anie.20035120310.1002/anie.200351203 ↗
10. Yoshio M, Wang HY, Fukuda K, Hara Y, Adachi Y (2000) Effect of carbon coating on electrochemical performance of treated natural graphite as lithium-ion battery anode material. J Electrochem Soc 147(4):1245–1250. doi: 10.1149/1.139334410.1149/1.1393344 ↗
11. Aravindan V, Lee Y-S, Yazami R, Madhavi S (2015) TiO2 polymorphs in ‘rocking-chair’ li-ion batteries. Mater Today 18(6):345–351. doi: 10.1016/j.mattod.2015.02.01510.1016/j.mattod.2015.02.015 ↗
12. Zachauchristiansen B, West K, Jacobsen T, Atlung S (1988) Lithium insertion in different TiO2 modifications. Solid State Ion 28:1176–1182. doi: 10.1016/0167-2738(88)90352-910.1016/0167-2738(88)90352-9 ↗
13. Ohzuku T, Kodama T, Hirai T (1985) Electrochemistry of anatase titanium-dioxide in lithium nonaqueous cells. J Power Sources 14(1–3):153–166. doi: 10.1016/0378-7753(85)88026-510.1016/0378-7753(85)88026-5 ↗
14. Brohan L, Marchand R (1983) Physical properties of bronze MxTiO2(B). Solid State Ion 9–10:419–42410.1016/0167-2738(83)90269-2 ↗
15. Gutierrez-Florez MT, Kuhn A, Garcia-Alvarado F (1999) Lithium intercalation in KxTi8O16 compounds. Int J Inorg Mater 1(1):117–12110.1016/S1463-0176(99)00018-6 ↗
16. Garcia-Alvarado F, de Dompablo M, Moran E, Gutierrez MT, Kuhn A, Varez A (1999) New electrode materials for lithium rechargeable batteries. J Power Sources 82:85–8910.1016/S0378-7753(98)00205-5 ↗
17. Kuhn A, Amandi R, Garcia-Alvarado F (2001) Electrochemical lithium insertion in TiO2 with the ramsdellite structure. J Power Sources 92(1–2):221–22710.1016/S0378-7753(00)00530-9 ↗
18. Kim C, Buonsanti R, Yaylian R, Milliron DJ, Cabana J (2013) Carbon-free TiO2 battery electrodes enabled by morphological control at the nanoscale. Adv Energy Mater 3(10):1286–1291. doi: 10.1002/aenm.20130026410.1002/aenm.201300264 ↗
19. Cozzoli PD, Kornowski A, Weller H (2003) Low-temperature synthesis of soluble and processable organic-capped anatase TiO2 nanorods. J Am Chem Soc 125(47):14539–14548. doi: 10.1021/ja036505h10.1021/ja036505h ↗
20. Buonsanti R, Pick TE, Krins N, Richardson TJ, Helms BA, Milliron DJ (2012) Assembly of ligand-stripped nanocrystals into precisely controlled mesoporous architectures. Nano Lett 12(7):3872–3877. doi: 10.1021/nl302206s10.1021/nl302206s ↗
21. Dinh C-T, Nguyen T-D, Kleitz F, Do T-O (2009) Shape-controlled synthesis of highly crystalline titania nanocrystals. ACS Nano 3(11):3737–3743. doi: 10.1021/nn900940p10.1021/nn900940p ↗
22. Myung S-T, Kikuchi M, Yoon CS, Yashiro H, Kim S-J, Sun Y-K, Scrosati B (2013) Black anatase titania enabling ultra high cycling rates for rechargeable lithium batteries. Energy Environ Sci 6(9):2609–2614. doi: 10.1039/c3ee41960f10.1039/c3ee41960f ↗
23. Ren Y, Liu Z, Pourpoint F, Armstrong AR, Grey CP, Bruce PG (2012) Nanoparticulate TiO2(B): an anode for lithium-ion batteries. Angew Chem Int Ed 51(9):2164–2167. doi: 10.1002/anie.20110830010.1002/anie.201108300 ↗
24. Armstrong AR, Armstrong G, Canales J, Garcia R, Bruce PG (2005) Lithium-ion intercalation into TiO2-B nanowires. Adv Mater 17(7):862–875. doi: 10.1002/adma.20040079510.1002/adma.200400795 ↗
25. Armstrong AR, Armstrong G, Canales J, Bruce PG (2005) TiO2-B nanowires as negative electrodes for rechargeable lithium batteries. J Power Sources 146(1–2):501–506. doi: 10.1016/j.jpowsour.2005.03.05710.1016/j.jpowsour.2005.03.057 ↗
26. Armstrong AR, Armstrong G, Canales J, Bruce PG (2004) TiO2-B nanowires. Angew Chem Int Ed 43(17):2286–2288. doi: 10.1002/anie.20035357110.1002/anie.200353571 ↗
27. Inaba M, Oba Y, Niina F, Murota Y, Ogino Y, Tasaka A, Hirota K (2009) TiO2(B) as a promising high potential negative electrode for large-size lithium-ion batteries. J Power Sources 189(1):580–584. doi: 10.1016/j.jpowsour.2008.10.00110.1016/j.jpowsour.2008.10.001 ↗
28. Saito M, Murota Y, Takagi M, Tajima M, Asao T, Inoue H, Tasaka A, Inaba M (2012) Improvement of the reversible capacity of TiO2(B) high potential negative electrode. J Electrochem Soc 159(1):A49–A54. doi: 10.1149/2.051201jes10.1149/2.051201jes ↗
29. de Dompablo M, Moran E, Varez A, GarciaAlvarado F (1997) Electrochemical lithium intercalation in Li2Ti3O7-ramsdellite structure. Mater Res Bull 32(8):993–100110.1016/S0025-5408(97)00080-9 ↗
30. Pérez-Flores JC, Kuhn A, García-Alvarado F (2011) Synthesis, structure and electrochemical li insertion behaviour of Li2Ti6O13 with the Na2Ti6O13 tunnel-structure. J Power Sources 196(3):1378–1385. doi: 10.1016/j.jpowsour.2010.08.10610.1016/j.jpowsour.2010.08.106 ↗
31. Dominko R, Baudrin E, Umek P, Arcon D, Gaberscek M, Jamnik J (2006) Reversible lithium insertion into Na2Ti6O13 structure. Electrochem Commun 8(4):673–67710.1016/j.elecom.2006.02.017 ↗
32. de Dompablo M, Varez A, Garcia-Alvarado F (2000) Structural study of electrochemically obtained Li2+xTi3O7. J Solid State Chem 153(1):132–13910.1006/jssc.2000.8762 ↗
33. Tsubone D, Hosoda T, Igarashi K, Shimizu T (1994) Synthesis and Thermal Expansion of Lithium Trititanate with Ramsdellite Type-Structure. Nippon Seramikkusu Kyokai Gakujutsu Ronbunshi. J Ceram Soc Japan 102(6):541–54510.2109/jcersj.102.541 ↗
34. Izquierdo G, West AR (1980) Phase equilibria in the system Li2O-TiO2. Mater Res Bull 15(11):1655–166010.1016/0025-5408(80)90248-2 ↗
35. Abrahams I, Bruce PG, David WIF, West AR (1989) Refinement of the lithium distribution in Li2Ti3O7 using high-resolution powder neutron diffraction. J Solid State Chem 78(1):170–177. doi: 10.1016/0022-4596(89)90141-210.1016/0022-4596(89)90141-2 ↗
36. Chen CJ, Greenblatt M (1985) Lithium insertion into Li2Ti3O7. Mater Res Bull 20(11):1347–135210.1016/0025-5408(85)90128-X ↗
37. Garnier S, Bohnke C, Bohnke O, Fourquet JL (1996) Electrochemical intercalation of lithium into the ramsdellite-type structure of Li2Ti3O7. Solid State Ion 83(3–4):323–332. doi: 10.1016/0167-2738(96)00002-110.1016/0167-2738(96)00002-1 ↗
38. Bohnke C, Fourquet JL, Randrianantoandro N, Brousse T, Crosnier O (2002) Electrochemical insertion of lithium into the ramsdellite-type oxide Li2Ti3O7: influence of the Li2Ti3O7 particle size. J Solid State Electrochem 6(6):403–411. doi: 10.1007/s10008010024310.1007/s100080100243 ↗
39. Cho W, Kashiwagi T, Ra W, Nakayama M, Wakihara M, Kobayashi Y, Miyashiro H (2009) Relationship between electrochemical behavior and Li/vacancy arrangement in ramsdellite type Li2+xTi3O7. Electrochim Acta 54(6):1842–1850. doi: 10.1016/j.electacta.2008.10.02110.1016/j.electacta.2008.10.021 ↗
40. Cho W, Park MS, Kim JH, Kim YJ (2012) Interfacial reaction between electrode and electrolyte for a ramsdellite type Li2+xTi3O7 anode material during lithium insertion. Electrochim Acta 63:263–268. doi: 10.1016/j.electacta.2011.12.09310.1016/j.electacta.2011.12.093 ↗
41. Chen F, Li RG, Hou M, Liu L, Wang R, Deng ZH (2005) Preparation and characterization of ramsdellite Li2Ti3O7 as an anode material for asymmetric supercapacitors. Electrochim Acta 51(1):61–65. doi: 10.1016/j.electacta.2005.03.04710.1016/j.electacta.2005.03.047 ↗
42. Ogihara T, Kodera T (2013) Synthesis of Li2Ti3O7 anode materials by ultrasonic spray pyrolysis and their electrochemical properties. Materials 6(6):2285–2294. doi: 10.3390/ma606228510.3390/ma6062285 ↗
43. Rietveld HM (1969) A profile refinement method for nuclear and magnetic structures. J Appl Crystallogr 2:65–7110.1107/S0021889869006558 ↗
44. Rodriguez Carvajal J (1993) Recent advances in magnetic-structure determination by neutron powder diffraction. Physica B 192(1–2):55–6910.1016/0921-4526(93)90108-I ↗
45. Sears VF (1992) Neutron scattering lengths and cross sections. Neutron News 3:29–3710.1080/10448639208218770 ↗
46. Momma K, Izumi F (2011) VESTA 3 for three-dimensional visualization of crystal, volumetric and morphology data. J Appl Crystallogr 44:1272–1276. doi: 10.1107/s002188981103897010.1107/S0021889811038970 ↗
47. Orera A, Azcondo MT, Garcia-Alvarado F, Sanz J, Sobrados I, Rodriguez-Carvajal J, Amador U (2009) Insight into ramsdellite Li2Ti3O7 and its proton-exchange derivative. Inorg Chem 48(16):7659–766610.1021/ic900398j ↗
48. Morosin B, Mikkelsen JC (1979) Crystal-structure of the Li + Ion conductor dilithium trititanate, Li2ti3o7. Acta Crystallogr Sect B 35(APR):798–80010.1107/S0567740879004921 ↗
49. Gover RKB, Irvine JTS, Finch AA (1997) Transformation of LiTi2O4 from spinel to ramsdellite on heating. J Solid State Chem 132(2):382–38810.1006/jssc.1997.7479 ↗
50. Gover RKB, Irvine JTS (1998) A new solid solution series linking LiTi2O4 and Li2Ti3O7 ramsdellites: a combined X-ray and neutron study. J Solid State Chem 141(2):365–372. doi: 10.1006/jssc.1998.794810.1006/jssc.1998.7948 ↗
51. He Y-B, Li B, Liu M, Zhang C, Lv W, Yang C, Li J, Du H, Zhang B, Yang Q-H, Kim J-K, Kang F (2012) Gassing in Li4Ti5O12-based batteries and its remedy. Sci Rep 2. Article number: 913. http://www.nature.com/srep/2012/121203/srep00913/abs/srep00913.html#supplementary-information10.1038/srep00913 ↗
52. Reimers JN, Dahn JR (1992) Electrochemical and insitu x-ray-diffraction studies of lithium intercalation in LiXCoO2. J Electrochem Soc 139(8):2091–2097. doi: 10.1149/1.222118410.1149/1.2221184 ↗
53. Ohzuku T, Ueda A (1994) Solid-state redox reactions of LiCoO2 (R(3)OVER-BAR-M) for 4 volt secondary lithium cells. J Electrochem Soc 141(11):2972–2977. doi: 10.1149/1.205926710.1149/1.2059267 ↗
54. Zou MJ, Yoshio M, Gopukumar S, Yamaki J (2004) Synthesis and electrochemical performance of high voltage cycling (LiMCoO2)-Co-0.05-O-0.95 as cathode material for lithium rechargeable cells. Electrochem Solid State Lett 7(7):A176–A17910.1149/1.1738423 ↗
55. Amatucci GG, Tarascon JM, Klein LC (1996) CoO2, the end member of the LixCoO2 solid solution. J Electrochem Soc 143(3):1114–1123. doi: 10.1149/1.183659410.1149/1.1836594 ↗