A study of surface fracture in paste extrusion using signal processing
Source abstract
Abstract
Gross circumferential fracture (GCF) is a surface defect sometimes observed during the extrusion of particulate pastes. In this study particular attention was paid to the frequency of fracture in pastes undergoing ram extrusion through dies with circular, square and rectangular slot cross section. Three methods for estimating the fracture frequency were employed. The first was determined from the observed fracture periodicity, the second was determined from the application of short time Fourier transformation (STFT) techniques to the pressure signal measured at the die plate and the third was the application of the geometrical result first reported by Domanti and Bridgwater (2000). All were found to be in agreement within experimental error where failure was observed. In some materials the fracture frequency was still observed in the frequency domain after fracture ceased in the extrudate, indicating the existence of a flow instability in the paste: if the extrudate was smooth throughout the process STFT detected no peak. Fracture was more pronounced with short dies and/or where the paste experienced high wall shear stress. Square dies were more prone to fracture than circular dies (corner effects) and the fracture spacing could be related directly to the hydraulic diameter. Rectangular slot dies were more prone to irregular fracture. It was shown that lowering the die wall friction by using Teflon-lined dies reduced the propensity of the paste to fracture for all die geometries tested.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Metallurgy and Material Forming · Powder Metallurgy Techniques and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. P. J. HARRISON, J. M. NEWTON and R. C. ROWE, J. Pharm. Pharmacol. 37 (1985) 81.10.1111/j.2042-7158.1985.tb05011.x ↗
2. A. T. J. DOMANTI and J. BRIDGWATER, Chem. Enging. Res. Des. 78(A) (2000) 68.10.1205/026387600526898 ↗
3. A. T. J. DOMANTI, D. J. HORROBIN and J. BRIDGWATER, Int. J. Mech. Sci. 44 (2002) 1381.10.1016/S0020-7403(02)00047-4 ↗
4. H. LL. D. PUGH and A. H. LOW, J. Inst. Met. 93 (1964) 201.
5. G. SORNBERGER and J. C. QUANTIN, J. Non-Newtonian Fluid Mech. 23 (1987) 123.10.1016/0377-0257(87)80014-9 ↗
6. Y. W. INN, R. J. FISHER and M. T. SHAW, Rheologica. Acta 37 (1998) 6.
7. R. P. G. RUTGERS and M. R. MACKLEY, J. Non-N. Fluid. Mech. 98 (2-3), (2001) 185.10.1016/S0377-0257(01)00103-3 ↗
8. O. L. KULIKOV and K. HORNUNG, J. Non-Newtonian Fluid Mech. 98 (2001) 107.10.1016/S0377-0257(01)00105-7 ↗
9. R. A. DIMILIA and J. S. REED, J. Amer. Ceram. Soc. 66(9) (1983) 667.10.1111/j.1151-2916.1983.tb10619.x ↗
10. J. J. BENBOW and J. BRIDGWATER, in “Paste Flow and Extrusion” (Clarendon Press, Oxford, 1993).
11. A. D. U. S. AMARASINGHE and D. I. WILSON, Chem. Enging. Res. Des. 76(A) (1998) 3.10.1205/026387698524523 ↗
12. Y. CHEN, A. S. BURBIDGE and J. BRIDGWATER, J. Amer. Ceram. Soc. 80 (7) (1998) 1841.10.1111/j.1151-2916.1997.tb03059.x ↗
13. S. P. T. SANDERS-HEWETT and D. J. DAVIES, Part IIB Research Project Reports, Department of Chemical Engineering, University of Cambridge, 2003.
14. A. CHEYNE, J. BARNES and D. I. WILSON, J. Food Enging. 66, 1.
15. O. L. KULIKOV and K. HORNUNG, J. Non-N. Fluid Mech. 107 (2002) 133.10.1016/S0377-0257(02)00145-3 ↗
16. G. Y. ONODA and L. L. HENCH, in “Ceramic Processing Before Firing” (John Wiley & Sons, NY, 1978).
17. A. D. U. S.Amarasinghe, Interpretation of paste extrusion data, PhD Dissertation, University of Cambridge, 1998.10.1205/026387698524523 ↗
18. Mathworks, Matlab Version 5.3, 1999.
19. S. MALLAT, in “A Wavelet Tour of Signal Processing” (Academic Press, 1998).10.1016/B978-012466606-1/50008-8 ↗
20. B. D. RUSSELL, S. BLACKBURN, D. I. WILSON and J. LASENBY, Application of On-Line Signal Processing to Paste Extrusion Data, submitted to IEEE Trans. Ind. App., 2004.
21. G. L. BRETTHORST, in “Bayesian Spectrum Analysis and Parameter Estimation” (Springer-Verlag, 1989).10.1007/978-1-4684-9399-3 ↗
22. J. J. K., Ó RUANAIDH and W.F. FITZGERALD, in “Numerical Bayesian Methods Applied to Signal Processing” (Springer, 1996).10.1007/978-1-4612-0717-7 ↗
23. J. P., BENTHAM and W. T KOITER, Asymptotic Approximations to Crack Problems, in “Methods of analysis and solutions of crack problems”, edited by G.C. Sih, (Noordhoff International Publishing, Leyden, 1973).10.1007/978-94-017-2260-5 ↗
24. S. BLACKBURN, A. S. BURBIDGE and H. MILLS, A Critical Assessment of the Benbow Approach to Describing the Extrusion of Highly Concentrated Particulate Suspensions and Pastes, Proc. XIIIth International Congress on Rheology, Cambridge, Paper 4-139-141, 2000.