Recrystallization-accelerated precipitation, structural evolution, and residual stress relaxation in nanostructured Al–Cu–Li alloy: an in situ microbeam synchrotron high-energy X-ray diffraction study
Source abstract
Abstract
Multidimensional synchrotron high-energy microbeam diffraction was applied to a nanostructured Al–1.1Cu–6.8Li–0.8X alloy (at%; X contains a total of minor elements) upon a constant heating ramp from room temperature to 830 K. Crystallography of a T1 precursor intermetallic as well as the T2 phase has been identified. Radial and azimuthal reciprocal space dimensions have been analyzed to determine Laue–Bragg interferences and their orientational statistics. The residual stress and texture determine the initial nanostructure of an ultrafine-grained cubic close-packed solid solution. While stress relaxes first, precipitation of precursor T1 sets in before any recrystallization, leading to nanoscale plate-shaped precipitates in the nanograins. Inherent with the onset of recrystallization, the T2 phase appears and grows by transformation from T1 and further precipitation from the matrix. At higher temperatures, T2 slowly dissolves again, while recrystallization ends and sluggish grain growth occurs in the two-phase field. The latter is accelerated toward the disappearance of T2 and becomes unhindered once the phase is fully dissolved. All these events mark anomalies in the curves for total lattice strain, small-momentum-transfer signals, and peak widths. The morphology of reflections on the Debye–Scherrer rings allows for determining grain sizes, which have been validated by electron microscopy and diffraction.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (64)
Show source-provided references
1. Muddle BC, Ringer SP, Polmear IJ (1994) High strength microalloyed aluminium alloys. Trans Mater Res Soc Jpn 19:999–1023. https://doi.org/10.1016/B978-1-4832-8382-1.50177-410.1016/B978-1-4832-8382-1.50177-4 ↗
2. Nie JF, Muddle BC (1998) Microstructural design of high-strength aluminum alloys. J Phase Equilibria 19:543–551. https://doi.org/10.1361/10549719877034173410.1361/105497198770341734 ↗
3. Gao X, Nie JF, Muddle BC (1998) Secondary hardening in 2090 (Al–Cu–Li) alloy. In: Proceedings of the 6th international conference on aluminum alloys. The Japan Institute of Light Metals, Toyohashi, pp 651–656
4. Rioja RJ, Ludwiczak EA (1986) Identification of metastable phases in Al-Cu-Li alloy (2090). In: Proceedings of the third international aluminium-lithium conference. The Institute of Metals, London, Oxford, pp 471–482
5. Prasad KS, Prasad NE, Gokhale AA (2014) Microstructure and Precipitate Characteristics of Aluminum–Lithium Alloys. In: Eswara Prasad N, Gokhale AA, Wanhill RJH (eds) Aluminum-lithium Alloys. Butterworth-Heinemann, Boston, pp 99–13710.1016/B978-0-12-401698-9.00004-5 ↗
6. Ma J, Liu X, Yan D, Rong L (2023) A novel GP-Li precursor and the correlated precipitation behaviors in Al-Cu-Li alloys with different Cu/Li ratio. Acta Mater 243:118442. https://doi.org/10.1016/j.actamat.2022.11844210.1016/j.actamat.2022.118442 ↗
7. Wang K, Zhang C, Cheng Z, Zhao H, Meng Z, Chen L, Zhao G (2024) Dynamic evolution of the T1 phase and its effect on continuous dynamic recrystallization in Al–Cu–Li alloys. Int J Plast 175:103948. https://doi.org/10.1016/j.ijplas.2024.10394810.1016/j.ijplas.2024.103948 ↗
8. Bartges C, Tosten MH, Howell PR, Ryba ER (1987) A combined single crystal x-ray diffraction and electron diffraction study of the T2phase in Al-Li-Cu alloys. J Mater Sci 22:1663–1669. https://doi.org/10.1007/BF0113238910.1007/BF01132389 ↗
9. Dénoyer F, Heger G, Lambert M, Lang JM, Sainfort P (1987) X-ray diffraction study on uniformly oriented quasicrystals. J Phys 48:1357–1361. https://doi.org/10.1051/jphys:01987004808013570010.1051/jphys:019870048080135700 ↗
10. Pauling L (1987) So-called icosahedral and decagonal quasicrystals are twins of an 820-atom cubic crystal. Phys Rev Lett 58:365–368. https://doi.org/10.1103/PhysRevLett.58.36510.1103/PhysRevLett.58.365 ↗
11. Chen R, Wang H, Sun Z, He B (2022) Study of icosahedral quasi-crystalline phase T2-Al6CuLi3 and transformation in 2A97 Al-Li alloy fabricated by laser additive manufacturing. Mater Lett 316:132014. https://doi.org/10.1016/j.matlet.2022.13201410.1016/j.matlet.2022.132014 ↗
12. Gao Z, Liu JZ, Chen JH, Duan SY, Liu ZR, Ming WQ, Wu CL (2015) Formation mechanism of precipitate T1 in AlCuLi alloys. J Alloys Compd 624:22–26. https://doi.org/10.1016/j.jallcom.2014.10.20810.1016/j.jallcom.2014.10.208 ↗
13. Gao Z, Chen J-H, Duan S-Y, Yang X-B, Wu C-L (2016) Complex precipitation sequences of Al-Cu-Li-(Mg) alloys characterized in relation to thermal ageing processes. Acta Metall Sin Engl Lett 29:94–103. https://doi.org/10.1007/s40195-016-0366-510.1007/s40195-016-0366-5 ↗
14. Liss K-D, Han J-K, Blankenburg M, Lienert U, Harjo S, Kawasaki T, Xu P, Yukutake E, Kawasaki M (2024) Recrystallization of bulk nanostructured magnesium alloy az31 after severe plastic deformation: an in situ diffraction study. J Mater Sci 59:5831–5853. https://doi.org/10.1007/s10853-023-09250-410.1007/s10853-023-09250-4 ↗
15. Kawasaki M (2014) Different models of hardness evolution in ultrafine-grained materials processed by high-pressure torsion. J Mater Sci 49:18–34. https://doi.org/10.1007/s10853-013-7687-910.1007/s10853-013-7687-9 ↗
16. Valiev RZ, Alexandrov IV, Kawasaki M, Langdon TG (2024) Ultrafine-grained materials. In: Ultrafine-grained materials: the minerals, metals & materials series. Springer, Cham.10.1007/978-3-031-31729-3 ↗
17. Edalati K, Ahmed AQ, Akrami S, Ameyama K, Aptukov V, Asfandiyarov RN, Ashida M, Astanin V, Bachmaier A, Beloshenko V et al (2024) Severe plastic deformation for producing superfunctional ultrafine-grained and heterostructured materials: an interdisciplinary review. J. Alloys Compd. 1002:174667. https://doi.org/10.1016/j.jallcom.2024.17466710.1016/j.jallcom.2024.174667 ↗
18. Han J-K, Liss K-D, Langdon TG, Jang J, Kawasaki M (2020) Mechanical properties and structural stability of a bulk nanostructured metastable aluminum-magnesium system. Mater Sci Eng A 796:140050. https://doi.org/10.1016/j.msea.2020.14005010.1016/j.msea.2020.140050 ↗
19. Han J-K, Sugimoto K, Kawasaki M, Liss K-D (2022) Strain-dependent phase transformation mapping of diffusion-bonded nanocrystalline aluminum-magnesium by high-energy synchrotron x-rays. Mater Lett 321:132414. https://doi.org/10.1016/j.matlet.2022.13241410.1016/j.matlet.2022.132414 ↗
20. Li X, Dippenaar RJ, Han J-K, Kawasaki M, Liss K-D (2019) Phase transformation and structure evolution of a Ti-45Al-7.5Nb alloy processed by high-pressure torsion. J. Alloys Compd. 787:1149–1157. https://doi.org/10.1016/j.jallcom.2019.02.17410.1016/j.jallcom.2019.02.174 ↗
21. Scheriau S, Zhang Z, Kleber S, Pippan R (2011) Deformation mechanisms of a modified 316L austenitic steel subjected to high pressure torsion. Mater Sci Eng A 528:2776–2786. https://doi.org/10.1016/j.msea.2010.12.02310.1016/j.msea.2010.12.023 ↗
22. Kawasaki M, Han J-K, Liu X, Onuki Y, Kuzminova YO, Evlashin SA, Pesin AM, Zhilyaev AP, Liss K-D (2022) In situ heating neutron and x-ray diffraction analyses for revealing structural evolution during postprinting treatments of additive-manufactured 316L stainless steel. Adv Eng Mater 24:2270017. https://doi.org/10.1002/adem.20227001710.1002/adem.202270017 ↗
23. Hung PT, Kawasaki M, Han J-K, Szabó Á, Lábár JL, Hegedűs Z, Gubicza J (2022) Thermal stability of nanocrystalline CoCrFeNi multi-principal element alloy: effect of the degree of severe plastic deformation. Intermetallics 142:107445. https://doi.org/10.1016/j.intermet.2021.10744510.1016/j.intermet.2021.107445 ↗
24. Liu X, Han J-K, Onuki Y, Kuzminova YO, Evlashin SA, Kawasaki M, Liss K-D (2023) In situ neutron diffraction investigating microstructure and texture evolution upon heating of nanostructured CoCrFeNi high-entropy alloy. Adv Eng Mater 25:2201256. https://doi.org/10.1002/adem.20220125610.1002/adem.202201256 ↗
25. Schuh B, Mendez-Martin F, Völker B, George EP, Clemens H, Pippan R, Hohenwarter A (2015) Mechanical properties, microstructure and thermal stability of a nanocrystalline CoCrFeMnNi high-entropy alloy after severe plastic deformation. Acta Mater 96:258–268. https://doi.org/10.1016/j.actamat.2015.06.02510.1016/j.actamat.2015.06.025 ↗
26. Maier-Kiener V, Schuh B, George EP, Clemens H, Hohenwarter A (2017) Nanoindentation testing as a powerful screening tool for assessing phase stability of nanocrystalline high-entropy alloys. Mater Des 115:479–485. https://doi.org/10.1016/j.matdes.2016.11.05510.1016/j.matdes.2016.11.055 ↗
27. Gubicza J (2020) Annealing-induced hardening in ultrafine-grained and nanocrystalline materials. Adv Eng Mater 22:1900507. https://doi.org/10.1002/adem.20190050710.1002/adem.201900507 ↗
28. Van Smaalen S, Meetsma A, De Boer JL, Bronsveld PM (1990) refinement of the crystal structure of hexagonal Al2CuLi. J Solid State Chem 85:293–298. https://doi.org/10.1016/S0022-4596(05)80086-610.1016/S0022-4596(05)80086-6 ↗
29. Pauling L (1988) Icosahedral quasicrystals as twins of cubic crystals containing large icosahedral clusters of atoms: the 1012-atom primitive cubic structure of Al6CuLi3, the C-phase Al37Cu3Li21Mg3, and GaMg2Zn3. Proc Natl Acad Sci 85:3666–3669. https://doi.org/10.1073/pnas.85.11.366610.1073/pnas.85.11.3666 ↗
30. Heiney PA, Bancel PA, Horn PM (1987) Comment on “so-called icosahedral and decagonal quasicrystals are twins of an 820-atom cubic crystal’’. Phys Rev Lett 59:2119–2119. https://doi.org/10.1103/PhysRevLett.59.211910.1103/PhysRevLett.59.2119 ↗
31. Li C, Li X, Zhang Y, Wen K, Yan L, Li Y, Li Y, Yu M, Gao G, Yan H et al (2025) Effect of Cu/Li ratio on mechanical properties and corrosion behavior of Sc-containing Al-Cu-Li alloys. Materials 18:2254. https://doi.org/10.3390/ma1810225410.3390/ma18102254 ↗
32. Kishio K, Brittain JO (1979) Defect structure of β-LiAl. J Phys Chem Solids 40:933–940. https://doi.org/10.1016/0022-3697(79)90121-510.1016/0022-3697(79)90121-5 ↗
33. Petschke D, Lotter F, Staab TEM (2019) Revisiting the crystal structure of the equilibrium S (Al2CuMg) phase in Al–Cu–Mg alloys using x-ray absorption spectroscopy (XAFS). Materialia 6:100341. https://doi.org/10.1016/j.mtla.2019.10034110.1016/j.mtla.2019.100341 ↗
34. Schueller RD, Sachdev AK, Wawner FE (1992) Identification of a cubic precipitate observed in an Al-4.3 Cu-2MgSiC cast composite. Scripta metallurgica et materialia 27(5):617–622. https://doi.org/10.1016/0956-716X(92)90350-N10.1016/0956-716X(92)90350-N ↗
35. Jiang B, Li S, Cao F, Song R, Yi X (2022) A new Al5Cu6(Li,Mg)2 cubic phase in an Al–Cu–Li–Mg–X alloy. Mater Charact 189:111971. https://doi.org/10.1016/j.matchar.2022.11197110.1016/j.matchar.2022.111971 ↗
36. Pan Z, Zheng Z, Liao Z, Li S (2010) New cubic precipitate in Al–3.5Cu–1.0Li–0.5In (Wt%) Alloy. Mater. Lett. 64:942–944. https://doi.org/10.1016/j.matlet.2010.01.06610.1016/j.matlet.2010.01.066 ↗
37. Pavlyuk V, Dmytriv G, Tarasiuk I, Pauly H, Ehrenberg H (2008) Li8Cu12+xAl6−x (x = 1.16): a new structure type related to laves phases. Acta Crystallogr. C 64:i15–i17. https://doi.org/10.1107/S010827010706598510.1107/S0108270107065985 ↗
38. Aluminium Lithium Alloy 2099 Aluminium. Available online. https://www.smithshp.com/shp-2099-ultimate.htm. Accessed 30 July 2025
39. Beygelzimer Y, Filippov A, Estrin Y (2023) ‘Turbulent’ shear flow of solids under high-pressure Torsion. Philos Mag 103:1017–1028. https://doi.org/10.1080/14786435.2023.218068110.1080/14786435.2023.2180681 ↗
40. Hughes DA, Hansen N (1997) High angle boundaries formed by grain subdivision mechanisms. Acta Mater 45:3871–3886. https://doi.org/10.1016/S1359-6454(97)00027-X10.1016/S1359-6454(97)00027-X ↗
41. Kim DH, Hutchison JL, Cantor B (1990) Deviation from icosahedral symmetry in rapidly solidified Al6Cu(Li, Mg)3 icosahedral phase. Philos Mag A 61:167–192. https://doi.org/10.1080/0141861900823493410.1080/01418619008234934 ↗
42. Starke EA (1991) Plastic behavior of Al–Li–X alloys. University of Virginia, Charlottesville
43. Liss K-D, Bartels A, Schreyer A, Clemens H (2003) High-energy x-rays: a tool for advanced bulk investigations in materials science and physics. Textures Microstruct 35:219–252. https://doi.org/10.1080/0730330031000163495210.1080/07303300310001634952 ↗
44. Hattori T, Saitoh H, Kaneko H, Okajima Y, Aoki K, Utsumi W (2006) Does bulk metallic glass of elemental Zr and Ti exist? Phys Rev Lett 96:255504. https://doi.org/10.1103/PhysRevLett.96.25550410.1103/PhysRevLett.96.255504 ↗
45. Kim K, Zhou B-C, Wolverton C (2018) First-principles study of crystal structure and stability of T1 precipitates in Al–Li–Cu alloys. Acta Mater 145:337–346. https://doi.org/10.1016/j.actamat.2017.12.01310.1016/j.actamat.2017.12.013 ↗
46. Huang JC, Ardell AJ (1987) Crystal structure and stability of T1, precipitates in aged Al–Li–Cu alloys. Mater Sci Technol 3:176–188. https://doi.org/10.1179/mst.1987.3.3.17610.1179/mst.1987.3.3.176 ↗
47. Howe JM, Lee J, Vasudévan AK (1988) Structure and deformation behavior o fT1 precipitate plates in an Al–2Li–1Cu alloy. Metall Trans A 19:2911–2920. https://doi.org/10.1007/BF0264771710.1007/BF02647717 ↗
48. Donnadieu P, Shao Y, De Geuser F, Botton GA, Lazar S, Cheynet M, de Boissieu M, Deschamps A (2011) Atomic structure of T1 precipitates in Al–Li–Cu alloys revisited with HAADF-STEM imaging and small-angle x-ray scattering. Acta Mater 59:462–472. https://doi.org/10.1016/j.actamat.2010.09.04410.1016/j.actamat.2010.09.044 ↗
49. Dwyer C, Weyland M, Chang LY, Muddle BC (2011) Combined electron beam imaging and Ab initio modeling of T1 precipitates in Al–Li–Cu alloys. Appl Phys Lett 98:201909. https://doi.org/10.1063/1.359017110.1063/1.3590171 ↗
50. Agustianingrum MP, Verma SK, Petschke D, Lotter F, Staab TEM, Tang S, Cao L, Zulfikar N, Cho H, Listyawan TA et al (2024) Revisiting precipitates in Al-Cu-Li alloys: experiments and first-principles calculations of thermodynamic stability of Al2CuLi(T1) precipitate. J Alloys Compd 991:174495. https://doi.org/10.1016/j.jallcom.2024.17449510.1016/j.jallcom.2024.174495 ↗
51. Lee I, Bhatta L, Xu D, Blankenburg M, Lienert U, Liss K-D, Kawasaki M (2025) Defect-driven relaxation of nanostructured Cu examined by in situ heating high-energy synchrotron x-ray microbeam diffraction. J Alloys Compd. 1028:180599. https://doi.org/10.1016/j.jallcom.2025.18059910.1016/j.jallcom.2025.180599 ↗
52. Li X, Dippenaar R, Shiro A, Shobu T, Higo Y, Reid M, Suzuki H, Akita K, Funakoshi K-I, Liss K-D (2018) Lattice parameter evolution during heating of Ti-45Al-7.5Nb-0.25/0.5C alloys under atmospheric and high pressures. Intermetallics 102:120–131. https://doi.org/10.1016/j.intermet.2018.08.01110.1016/j.intermet.2018.08.011 ↗
53. Liss K-D, Bartels A, Clemens H, Bystrzanowski S, Stark A, Buslaps T, Schimansky F-P, Gerling R, Scheu C, Schreyer A (2006) Recrystallization and phase transitions in a gamma-TiAl-based alloy as observed by ex situ and in situ high-energy x-ray diffraction. Acta Mater 54:3721–3735. https://doi.org/10.1016/j.actamat.2006.04.00410.1016/j.actamat.2006.04.004 ↗
54. Yan K, Liss K-D, Garbe U, Daniels J, Kirstein O, Li H, Dippenaar R (2009) From single grains to texture. Adv Eng Mater 11:771–773. https://doi.org/10.1002/adem.20090016310.1002/adem.200900163 ↗
55. Liss K-D, Garbe U, Li H, Schambron T, Almer JD, Yan K (2009) In situ observation of dynamic recrystallization in the bulk of zirconium alloy. Adv Eng Mater 11:637–640. https://doi.org/10.1002/adem.20090009410.1002/adem.200900094 ↗
56. Liss K-D, Schmoelzer T, Yan K, Reid M, Peel M, Dippenaar R, Clemens H (2009) In situ study of dynamic recrystallization and hot deformation behavior of a multiphase titanium aluminide alloy. J Appl Phys 106:113526. https://doi.org/10.1063/1.326617710.1063/1.3266177 ↗
57. Liss K-D, Yan K (2010) Thermo-mechanical processing in a synchrotron beam. Mater Sci Eng Struct Mater Prop Microstruct Process 528:11–27. https://doi.org/10.1016/j.msea.2010.06.01710.1016/j.msea.2010.06.017 ↗
58. Han J-K, Liu X, Lee I, Kuzminova YO, Evlashin SA, Liss K-D, Kawasaki M (2021) Structural evolution during nanostructuring of additive manufactured 316L stainless steel by high-pressure Torsion. Mater Lett 302:130364. https://doi.org/10.1016/j.matlet.2021.13036410.1016/j.matlet.2021.130364 ↗
59. Hidnert P (1924) Thermal expansion of aluminum and various important aluminum alloys. Sci Pap Bur Stand 19:697–731. https://doi.org/10.6028/nbsscipaper.17910.6028/nbsscipaper.179 ↗
60. Liss K-D, Harjo S, Kawasaki T, Aizawa K, Xu PG (2021) Anisotropic thermal lattice expansion and crystallographic structure of strontium aluminide within Al–10Sr alloy as measured by in-situ neutron diffraction. J Alloys Compd 869:159232. https://doi.org/10.1016/j.jallcom.2021.15923210.1016/j.jallcom.2021.159232 ↗
61. Liss K-D, Qu D, Yan K, Reid M (2013) Variability of Poisson’s ratio and enhanced ductility in amorphous metal. Adv Eng Mater 15:347–351. https://doi.org/10.1002/adem.20120021610.1002/adem.201200216 ↗
62. Yang X, Wang J, Zhang M, Zhang C, Xue C, Guo Y, Liu X (2021) Achieving high strength and ductility of Al–Cu–Li alloy via creep aging treatment with different pre-strain levels. Mater Today Commun 29:102898. https://doi.org/10.1016/j.mtcomm.2021.10289810.1016/j.mtcomm.2021.102898 ↗
63. Uesugi T, Higashi K (2013) First-principles studies on lattice constants and local lattice distortions in solid solution aluminum alloys. Comput Mater Sci 67:1–10. https://doi.org/10.1016/j.commatsci.2012.08.03710.1016/j.commatsci.2012.08.037 ↗
64. Yan K, Carr DG, Kabra S, Reid M, Studer A, Harrison RP, Dippenaar R, Liss K-D (2011) In situ characterization of lattice structure evolution during phase transformation of Zr–2.5Nb. Adv. Eng. Mater. 13:882–886. https://doi.org/10.1002/adem.20100035010.1002/adem.201000350 ↗