journal article·2026-07Open access

Study of Zn–Ag alloys prepared via powder metallurgy

V. Čákyová, R. Gorejová, M. Kupková, M. Džupon, T. Sopčák, M. Faberová, K. Ozaltin, M. Strečková, R. Oriňaková

Journal of Materials Science· Volume 61· Issue 27

Abstract

Abstract Orthopaedic biomaterials require a balance between mechanical integrity and controlled degradation. Among biodegradable metals, magnesium-based alloys degrade too rapidly, leading to premature loss of mechanical support, whereas iron-based alloys exhibit slow degradation and high stiffness, which may limit their clinical applicability. In contrast, zinc-based materials offer a more favourable combination of moderate corrosion rate and mechanical properties closer to natural bone. However, the relatively low mechanical strength of pure zinc remains a critical limitation, highlighting the need for effective alloying and processing strategies. In this context, the incorporation of silver represents a promising approach to enhance both the mechanical strength and antibacterial performance of zinc. Despite this potential, the combined effect of composition and processing route, particularly cost-effective techniques such as powder metallurgy, on the structural and functional behaviour of Zn-Ag systems remains insufficiently understood. In this study, binary alloys Zn-xAg ( x = 2.0, 4.0, 6.0 wt% Ag) and pure Zn were prepared using powder metallurgy. The structure, corrosion behaviour, surface morphology, and wettability were evaluated. The highest corrosion rate of 0.353 mm year −1 was observed for the pure Zn sample. Atomic force microscopy revealed that the surface of pure zinc was the smoothest, while the roughness of Zn-Ag alloys increased with silver content. X-ray diffraction analysis confirmed the presence of intermetallic phases. Furthermore, contact angle measurements indicated slightly hydrophilic surfaces, which could promote cell adhesion. These findings demonstrate that Zn-Ag alloys processed via powder metallurgy represent a promising strategy for tailoring the mechanical and functional performance of zinc-based implants.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Material Properties and Applications · Metallurgy and Material Science

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (100+)

Show source-provided references
1. Liu Y, Du T, Qiao A, Mu Y, Yang H (2022) Zinc-based biodegradable materials for orthopaedic internal fixation. J Funct Biomater.13(4) https://doi.org/10.3390/jfb1304016410.3390/jfb13040164 ↗
2. Suzuki H, Imajo Y, Funaba M, Ikeda H, Nishida N, Sakai T (2023) Current concepts of biomaterial scaffolds and regenerative therapy for spinal cord injury. Int J Mol Sci.24(4) https://doi.org/10.3390/ijms2403252810.3390/ijms24032528 ↗
3. Bandyopadhyay A, Mitra I, Goodman SB, Kumar M, Bose S (2023) Improving biocompatibility for next generation of metallic implants. Prog Mater Sci.33 https://doi.org/10.1016/j.pmatsci.2022.10105310.1016/j.pmatsci.2022.101053 ↗
4. Thanigaivel S, Priya AK, Balakrishnan D, Dutta K, Rajendran S, Soto-Moscoso M (2022) Insight on recent development in metallic biomaterials: strategies involving synthesis, types and surface modification for advanced therapeutic and biomedical applications. Biochem Eng J. 87 https://doi.org/10.1016/j.bej.2022.10852210.1016/j.bej.2022.108522 ↗
5. Cui YW, Wang L, Zhang LC (2024) Towards load-bearing biomedical titanium-based alloys: from essential requirements to future developments. Prog Mater Sci. 144 https://doi.org/10.1016/j.pmatsci.2024.10127710.1016/j.pmatsci.2024.101277 ↗
6. Guo C, Ding T, Cheng Y, Zheng J, Fang X, Feng Z (2025) The rational design, biofunctionalization and biological properties of orthopedic porous titanium implants: a review. Front Bioeng Biotechnol. 13 https://doi.org/10.3389/fbioe.2025.154867510.3389/fbioe.2025.1548675 ↗
7. Pattanayak S et al (2025) Additive manufacturing of 316 L stainless steel orthopedic implant with improved in vitro hemocompatibility and hydrophilicity for osteoinduction in Wistar rat model. Biomater Adv.175 https://doi.org/10.1016/j.bioadv.2025.21432210.1016/j.bioadv.2025.214322 ↗
8. Ronin D, Boyer J, Alban N, Natoli RM, Johnson A, Kjellerup BV (2022) Current and novel diagnostics for orthopedic implant biofilm infections: a review.130(2)59-81 APMIS. https://doi.org/10.1111/apm.1319710.1111/apm.13197 ↗
9. Lu Y, Cai WJ, Ren Z, Han P (2022) The role of staphylococcal biofilm on the surface of implants in orthopedic infection. Microorganisms. 9(4) https://doi.org/10.3390/microorganisms1010190910.3390/microorganisms10101909 ↗
10. Heye P et al (2022) Making hardware removal unnecessary by using resorbable implants for osteosynthesis in children. Children.9(4) https://doi.org/10.3390/children904047110.3390/children9040471 ↗
11. Chandra G, Pandey A (2020) Biodegradable bone implants in orthopedic applications: a review. Biocybern Biomed Eng. 40(2)596-610 https://doi.org/10.1016/j.bbe.2020.02.00310.1016/j.bbe.2020.02.003 ↗
12. Wang P, Gong Y, Zhou G, Ren W, Wang X (2023) Biodegradable implants for internal fixation of fractures and accelerated bone regeneration. ACS Omega.8(31)27920-27931 https://doi.org/10.1021/acsomega.3c0272710.1021/acsomega.3c02727 ↗
13. Zheng YF, Gu XN, Witte F (2014) Biodegradable metals. Mater Sci Eng R Rep. 77(1)34 https://doi.org/10.1016/j.mser.2014.01.00110.1016/j.mser.2014.01.001 ↗
14. Gorejová R et al (2020) In vitro corrosion behavior of biodegradable iron foams with polymeric coating. Materials 13(1):184. https://doi.org/10.3390/ma1301018410.3390/ma13010184 ↗
15. Gutiérrez Púa LDC, Rincón Montenegro JC, Fonseca Reyes AM, Zambrano Rodríguez H, Paredes Méndez VN (2023) Biomaterials for orthopedic applications and techniques to improve corrosion resistance and mechanical properties for magnesium alloy: a review. J Mater Sci.58:3879-3908 https://doi.org/10.1007/s10853-023-08237-510.1007/s10853-023-08237-5 ↗
16. Akinwekomi AD, Akhtar F (2023) Tunability of mechanical and biodegradation properties of zinc-based biomaterial with calcium micronutrient alloying. J Mech Behav Biomed Mater.40 https://doi.org/10.1016/j.jmbbm.2023.10572410.1016/j.jmbbm.2023.105724 ↗
17. Čákyová V et al (2024) Biodegradable iron-based foams prepared by the space holder technique using urea. J Appl Electrochem 54(3):625–634. https://doi.org/10.1007/s10800-023-01993-x10.1007/s10800-023-01993-x ↗
18. Li P et al (2024) Zinc based biodegradable metals for bone repair and regeneration: bioactivity and molecular mechanisms. Mater Today Bio. 25 https://doi.org/10.1016/j.mtbio.2023.10093210.1016/j.mtbio.2023.100932 ↗
19. Chen S et al (2024) Methods for improving the properties of zinc for the application of biodegradable vascular stents. Biomater Adv. 156 https://doi.org/10.1016/j.bioadv.2023.21369310.1016/j.bioadv.2023.213693 ↗
20. Chen K, Gu X, Zheng Y (2024) Feasibility, challenges and future prospects of biodegradable zinc alloys as orthopedic internal fixation implants. Smart Mater Manuf.2 https://doi.org/10.1016/j.smmf.2023.10004210.1016/j.smmf.2023.100042 ↗
21. Kaveh M, Badrossamay M, Foroozmehr E, Kharaziha M (2025) Biodegradability, biocompatibility, and mechanical behavior of additively manufactured zinc scaffolds. J Mech Behav Biomed Mater.163 https://doi.org/10.1016/j.jmbbm.2024.10686810.1016/j.jmbbm.2024.106868 ↗
22. El-Agawany NI, Kaamoush MIA (2023) Role of zinc as an essential microelement for algal growth and concerns about its potential environmental risks. Environ Sci Pollut Res 30(28):71900–71911. https://doi.org/10.1007/s11356-022-20536-z10.1007/s11356-022-20536-z ↗
23. Sekar P, S N, Desai V (2021) Recent progress in in vivo studies and clinical applications of magnesium based biodegradable implants—a review. J Magnesium Alloys.9(4)1174-1163 https://doi.org/10.1016/j.jma.2020.11.00110.1016/j.jma.2020.11.001 ↗
24. Kafri A, Ovadia S, Yosafovich-Doitch G, Aghion E (2018) In vivo performances of pure Zn and Zn–Fe alloy as biodegradable implants. J Mater Sci Mater Med.29 https://doi.org/10.1007/s10856-018-6096-710.1007/s10856-018-6096-7 ↗
25. Badhe RV, Akinfosile O, Bijukumar D, Barba M, Mathew MT (2021) Systemic toxicity eliciting metal ion levels from metallic implants and orthopedic devices—a mini review. Toxicol Lett.350:213-224 https://doi.org/10.1016/j.toxlet.2021.07.00410.1016/j.toxlet.2021.07.004 ↗
26. Qin Y et al (2022) Additive manufacturing of Zn-Mg alloy porous scaffolds with enhanced osseointegration: in vitro and in vivo studies. Acta Biomater 145:403–415. https://doi.org/10.1016/j.actbio.2022.03.05510.1016/j.actbio.2022.03.055 ↗
27. Su Y et al (2022) Improved mechanical, degradation, and biological performances of Zn–Fe alloys as bioresorbable implants. Bioact Mater 17:334–343. https://doi.org/10.1016/j.bioactmat.2021.12.03010.1016/j.bioactmat.2021.12.030 ↗
28. Qiao H, Li Q, Zhang J, Yang J, Han C, Dong Z (2025) Investigation on the microstructure, mechanical performances, in vitro degradation behavior and biocompatibility of biodegradable Zn-0.5Sr alloy by Li alloying and extruded deformation. Mater Chem Phys. 338 https://doi.org/10.1016/j.matchemphys.2025.13066410.1016/j.matchemphys.2025.130664 ↗
29. Tang Y et al (2025) Zn-Mn-Mg alloy with superior mechanical properties and antibacterial performance. Adv Compos Hybrid Mater. 8(1) https://doi.org/10.1007/s42114-024-01071-610.1007/s42114-024-01071-6 ↗
30. Chen HT, Shi ZZ, Liu XF (2020) Microstructure and mechanical properties of extruded and caliber rolled biodegradable Zn-0.8Mn-0.4Ag alloy with high ductility. Mater Sci Eng A.770 https://doi.org/10.1016/j.msea.2019.13854310.1016/j.msea.2019.138543 ↗
31. Li XM, Shi ZZ, Zhang JY, Zhou C, Wang LN (2025) 380 MPa-30% grade biodegradable Zn-Mn-Mg-Ca alloy: bimodal grain structure, large work-hardening strain, and enhanced biocompatibility. Acta Biomater 193:584–603. https://doi.org/10.1016/j.actbio.2024.12.05010.1016/j.actbio.2024.12.050 ↗
32. Sun H et al (2025) Spatiotemporal regulation of the bone immune microenvironment via a ‘Zn2+-quercetin’ hierarchical delivery system for bone regeneration. Regen Biomater. 12 https://doi.org/10.1093/rb/rbaf00610.1093/rb/rbaf006 ↗
33. Shearier ER et al (2016) In vitro cytotoxicity, adhesion, and proliferation of human vascular cells exposed to zinc. ACS Biomater Sci Eng 2(4):634–642. https://doi.org/10.1021/acsbiomaterials.6b0003510.1021/acsbiomaterials.6b00035 ↗
34. Wojtas D et al (2024) Verifying the cytotoxicity of a biodegradable zinc alloy with nanodiamond sensors. Biomater Adv. 162 https://doi.org/10.1016/j.bioadv.2024.21392710.1016/j.bioadv.2024.213927 ↗
35. Galib RH, Sharif A (2016) Development of Zn-Mg alloys as a degradable biomaterial. C Int Publ Adv Alloys Compd 1(1):1–7. https://doi.org/10.7726/aac.2016.100110.7726/aac.2016.1001 ↗
36. Jiang J, Qian Y, Huang H, Niu J, Yuan G (2022) Biodegradable Zn-Cu-Mn alloy with suitable mechanical performance and in vitro degradation behavior as a promising candidate for vascular stents. Biomater Adv.133 https://doi.org/10.1016/j.msec.2022.11265210.1016/j.msec.2022.112652 ↗
37. Niu K, Zhang D, Qi F, Lin J, Dai Y (2024) Achieving high strength and antibacterial Zn−4Ag−Mn alloy with homogenous corrosion behavior via high-pressure solid solution. Trans Nonferrous Met Soc China 34(7):2231–2244. https://doi.org/10.1016/S1003-6326(24)66537-410.1016/S1003-6326(24)66537-4 ↗
38. Caligari Conti M, Mallia B, Sinagra E, Schembri Wismayer P, Buhagiar J, Vella D (2019) The effect of alloying elements on the properties of pressed and non-pressed biodegradable Fe–Mn–Ag powder metallurgy alloys. Heliyon.5(9) https://doi.org/10.1016/j.heliyon.2019.e0252210.1016/j.heliyon.2019.e02522 ↗
39. Yuan W, Xia D, Wu S, Zheng Y, Guan Z, Rau JV (2022) A review on current research status of the surface modification of Zn-based biodegradable metals. Bioact Mater.7:192-216 https://doi.org/10.1016/j.bioactmat.2021.05.01810.1016/j.bioactmat.2021.05.018 ↗
40. Xie Y, Zhao L, Zhang Z, Wang X, Wang R, Cui C (2018) Fabrication and properties of porous Zn-Ag alloy scaffolds as biodegradable materials. Mater Chem Phys 219:433–443. https://doi.org/10.1016/j.matchemphys.2018.08.02310.1016/j.matchemphys.2018.08.023 ↗
41. Shuai C, Xue L, Gao C, Yang Y, Peng S, Zhang Y (2018) Selective laser melting of Zn–Ag alloys for bone repair: microstructure, mechanical properties and degradation behaviour. Virtual and Physical Prototyping 13(3):146–154. https://doi.org/10.1080/17452759.2018.145899110.1080/17452759.2018.1458991 ↗
42. Qu X et al (2021) Zinc alloy-based bone internal fixation screw with antibacterial and anti-osteolytic properties. Bioact Mater 6(12):4607–4624. https://doi.org/10.1016/j.bioactmat.2021.05.02310.1016/j.bioactmat.2021.05.023 ↗
43. Ke B et al (2021) Powder metallurgy of high-entropy alloys and related composites: a short review. Int J Miner Metall Mater. 28:931-943 https://doi.org/10.1007/s12613-020-2221-y10.1007/s12613-020-2221-y ↗
44. Sharma SK et al (2025) Significance of the powder metallurgy approach and its processing parameters on the mechanical behavior of magnesium-based materials. Nanomaterials. 15(2) https://doi.org/10.3390/nano1502009210.3390/nano15020092 ↗
45. Sharma SK, Saxena KK (2022) An outlook on the influence on mechanical properties of AZ31 reinforced with graphene nanoparticles using powder metallurgy technique for biomedical application. Mater Today Proc 56:2278–2287. https://doi.org/10.1016/j.matpr.2021.11.62710.1016/j.matpr.2021.11.627 ↗
46. Torralba JM, Campos M (2014) Toward high performance in Powder Metallurgy. Centro Nacional de Investigaciones Metalurgicas. https://doi.org/10.3989/revmetalm.01710.3989/revmetalm.017 ↗
47. Froes FH, Pickens JR (1984) Powder metallurgy of light metal alloys for demanding applications. JOM 36(1):14–2810.1007/BF03339911 ↗
48. ISO (2006) ISO 3369:2006 - Impermeable sintered metal materials and hardmetals - Determination of density, Geneva, Switzerland: International Organization for Standardization, International Organization for Standaritization (ISO)
49. Wei S, Ma JX, Xu L, Gu XS, Ma XL (2020) Biodegradable materials for bone defect repair. Mil Med Res.7 https://doi.org/10.1186/s40779-020-00280-610.1186/s40779-020-00280-6 ↗
50. “Corrosion of metals and alloys-Removal of corrosion products from corrosion test specimens Corrosion des métaux et alliages-Élimination des produits de corrosion sur les éprouvettes d’essai de corrosion INTERNATIONAL STANDARD ISO 8407,” 2021. [Online]. Available: www.iso.org
51. “Standard Test Method for Dynamic Young’s Modulus, Shear Modulus, and Poisson’s Ratio by Impulse Excitation of Vibration 1.”
52. Hu X, Wang T, Li F, Mao X (2023) Surface modifications of biomaterials in different applied fields. RSC Adv.13(30)20495-20511 https://doi.org/10.1039/d3ra02248j10.1039/d3ra02248j ↗
53. Rahmati M, Silva EA, Reseland JE, Heyward CA, Haugen HJ (2020) Biological responses to physicochemical properties of biomaterial surface. Chem Soc Rev. 49(15)5178-5224 https://doi.org/10.1039/d0cs00103a10.1039/d0cs00103a ↗
54. bin A. Fadzil AF, Pramanik A, Basak AK, Prakash C, Shankar S (2022) Role of surface quality on biocompatibility of implants - a review. Ann 3D Print Med. 8 https://doi.org/10.1016/j.stlm.2022.10008210.1016/j.stlm.2022.100082 ↗
55. Vallés G, Gil-Garay E, Munuera L, Vilaboa N (2008) Modulation of the cross-talk between macrophages and osteoblasts by titanium-based particles. Biomaterials 29(15):2326–2335. https://doi.org/10.1016/j.biomaterials.2008.02.01110.1016/j.biomaterials.2008.02.011 ↗
56. Martinez MAF et al (2020) Surface roughness of titanium disks influences the adhesion, proliferation and differentiation of osteogenic properties derived from human. Int J Implant Dent.6(1) https://doi.org/10.1186/s40729-020-00243-510.1186/s40729-020-00243-5 ↗
57. Wang Q et al (2020) Multi-scale surface treatments of titanium implants for rapid osseointegration: a review. Nanomaterials. 13(6)1-27 https://doi.org/10.3390/nano1006124410.3390/nano10061244 ↗
58. Liu Y, Rath B, Tingart M, Eschweiler J (2020) Role of implants surface modification in osseointegration: a systematic review. J Biomed Mater Res A. 108(3)470-484 https://doi.org/10.1002/jbm.a.3682910.1002/jbm.a.36829 ↗
59. Meirelles L, Arvidsson A, Andersson M, Kjellin P, Albrektsson T, Wennerberg A (2008) Nano hydroxyapatite structures influence early bone formation. J Biomed Mater Res A 87(2):299–307. https://doi.org/10.1002/jbm.a.3174410.1002/jbm.a.31744 ↗
60. Jagtap RN, Ambre AH (2006) Overview literature on atomic force microscopy (AFM): Basics and its important applications for polymer characterization. Indian J Eng Mater Sci 13(4):368
61. Wang K, Taylor KG, Ma L (2021) Advancing the application of atomic force microscopy (AFM) to the characterization and quantification of geological material properties. Int J Coal Geol. https://doi.org/10.1016/j.coal.2021.10385210.1016/j.coal.2021.103852 ↗
62. Roesner M, Zankovic S, Kovacs A, Benner M, Barkhoff R, Seidenstuecker M (2023) Biocompatibility assessment of Zinc alloys as a new potential material for bioabsorbable implants for osteosynthesis. Materials.16(15) https://doi.org/10.3390/ma1615522410.3390/ma16155224 ↗
63. Wątroba M et al (2023) In vitro cytocompatibility and antibacterial studies on biodegradable Zn alloys supplemented by a critical assessment of direct contact cytotoxicity assay. J Biomed Mater Res B Appl Biomater 111(2):241–260. https://doi.org/10.1002/jbm.b.3514710.1002/jbm.b.35147 ↗
64. Andrukhov O et al (2016) Proliferation, behavior, and differentiation of osteoblasts on surfaces of different microroughness. Dent Mater 32(11):1374–1384. https://doi.org/10.1016/j.dental.2016.08.21710.1016/j.dental.2016.08.217 ↗
65. Qasim I, Mumtaz M, Nadeem K, Abbas SQ (2016) Zinc nanoparticles at intercrystallite sites of (Cu0.5Tl0.5)Ba2Ca3Cu4O12-δ superconductor. J Nanomater. https://doi.org/10.1155/2016/978179010.1155/2016/9781790 ↗
66. Khatibi AD, Chandrika K, Mostafapour FK, Sajadi AA, Balarak D (2021) Photocatalytic degradation of Naphthalene by UV/Zno: kinetics, influencing factors and mechanisms. Orient J Chem 37(1):65–70. https://doi.org/10.13005/ojc/37010810.13005/ojc/370108 ↗
67. Mandal M, Moon AP, Sangal S, Mondal K (2014) Nanoporous Ag template from partially sintered Ag-Zn compact by dezincification. Bull Mater Sci 37(6):1353–136710.1007/s12034-014-0083-5 ↗
68. Zhang Y, Gao G, Qian Q, Cui D (2012) Chloroplasts-mediated biosynthesis of nanoscale Au-Ag alloy for 2-butanone assay based on electrochemical sensor. Nanoscale Res Lett. 7 https://doi.org/10.1186/1556-276X-7-47510.1186/1556-276X-7-475 ↗
69. Gnanamuthu RM et al (2024) Influence of crystalline Zn-Ag nanoalloy electrodeposits on their anti-corrosion and hardness performance in engineering applications. Ionics (Kiel) 30(8):4845–4852. https://doi.org/10.1007/s11581-024-05600-710.1007/s11581-024-05600-7 ↗
70. Elliott BM, Sung K, Miller CE (2015) FT-IR spectra of 18O-, and 13C-enriched CO2 in the ν3 region: high accuracy frequency calibration and spectroscopic constants for 16O12C18O, 18O12C18O, and 16O13C16O. J Mol Spectrosc 312:78–86. https://doi.org/10.1016/j.jms.2015.02.00710.1016/j.jms.2015.02.007 ↗
71. Gorejová R, Ozaltin K, Šišoláková I, Kupková M, Sáha P, Oriňaková R (2023) Fucoidan- and Ciprofloxacin-doped plasma-activated polymer coatings on biodegradable zinc: hemocompatibility and drug release. ACS Omega 8(47):44850–44860. https://doi.org/10.1021/acsomega.3c0604810.1021/acsomega.3c06048 ↗
72. Mohamed MA, Jaafar J, Ismail AF, Othman MHD, Rahman MA (2017) Fourier Transform Infrared (FTIR) spectroscopy. In: Membrane characterization, Elsevier Inc., pp 3–29. https://doi.org/10.1016/B978-0-444-63776-5.00001-210.1016/B978-0-444-63776-5.00001-2 ↗
73. Chakarova K, Drenchev N, Hadjiivanov K (2012) FTIR evidence of different bonding of methane to OH groups on H-ZSM-5, HY, and SiO 2. J Phys Chem C 116(32):17101–17109. https://doi.org/10.1021/jp305259210.1021/jp3052592 ↗
74. George M, Pandey AK, Abd Rahim N, Tyagi VV, Shahabuddin S, Saidur R (2020) A novel polyaniline (PANI)/ paraffin wax nano composite phase change material: superior transition heat storage capacity, thermal conductivity and thermal reliability. Sol Energy 204:448–458. https://doi.org/10.1016/j.solener.2020.04.08710.1016/j.solener.2020.04.087 ↗
75. Gunasekaran S, Anbalagan G, Pandi S (2006) Raman and infrared spectra of carbonates of calcite structure. J Raman Spectrosc 37(9):892–899. https://doi.org/10.1002/jrs.151810.1002/jrs.1518 ↗
76. Hoffmann J, Jensen CU, Rosendahl LA (2016) Co-processing potential of HTL bio-crude at petroleum refineries - Part 1: Fractional distillation and characterization. Fuel 165:526–535. https://doi.org/10.1016/j.fuel.2015.10.09410.1016/j.fuel.2015.10.094 ↗
77. Liu X et al (2013) Understanding the factors that control the formation and morphology of Zn5 (OH)8 (NO3)2 · 2 H 2O through hydrothermal route. J Nanomater. https://doi.org/10.1155/2013/93837010.1155/2013/938370 ↗
78. Rouchon V et al (2012) Raman and FTIR spectroscopy applied to the conservation report of paleontological collections: identification of Raman and FTIR signatures of several iron sulfate species such as Ferrinatrite and Sideronatrite. J Raman Spectrosc 43(9):1265–1274. https://doi.org/10.1002/jrs.404110.1002/jrs.4041 ↗
79. Valdez S, Ascencio JA, Meneses A, Casolco SR (2014) Redox reactions values of AlZn + Ag eutectoid chemical composition. J Mater Sci Chem Eng 02(08):12–16. https://doi.org/10.4236/msce.2014.2800310.4236/msce.2014.28003 ↗
80. Chen Y et al (2016) Comparative corrosion behavior of Zn with Fe and Mg in the course of immersion degradation in phosphate buffered saline. Corros Sci 111:541–555. https://doi.org/10.1016/j.corsci.2016.05.03910.1016/j.corsci.2016.05.039 ↗
81. Furko M, Jiang Y, Wilkins T, Balázsi C (2016) Development and characterization of silver and zinc doped bioceramic layer on metallic implant materials for orthopedic application. Ceram Int 42(4):4924–4931. https://doi.org/10.1016/j.ceramint.2015.12.00610.1016/j.ceramint.2015.12.006 ↗
82. Zhang S et al (2010) Research on an Mg-Zn alloy as a degradable biomaterial. Acta Biomater 6(2):626–640. https://doi.org/10.1016/j.actbio.2009.06.02810.1016/j.actbio.2009.06.028 ↗
83. García-Mintegui C et al (2024) Dual peptide functionalization of Zn alloys to enhance endothelialization for cardiovascular applications. Appl Surf Sci. 645 https://doi.org/10.1016/j.apsusc.2023.15890010.1016/j.apsusc.2023.158900 ↗
84. Aggarwal D, Kumar V, Sharma S (2022) Drug-loaded biomaterials for orthopedic applications: a review. J Controlled Release 344:113–133. https://doi.org/10.1016/j.jconrel.2022.02.02910.1016/j.jconrel.2022.02.029 ↗
85. Li P et al (2018) Mechanical characteristics, in vitro degradation, cytotoxicity, and antibacterial evaluation of Zn-4.0Ag alloy as a biodegradable material. Int J Mol Sci.21(6) https://doi.org/10.3390/ijms1903075510.3390/ijms19030755 ↗
86. Xiao X, Liu E, Shao J, Ge S (2021) Advances on biodegradable zinc-silver-based alloys for biomedical applications. J Appl Biomater Funct Mater 19:22808000211062410. https://doi.org/10.1177/2280800021106240710.1177/22808000211062407 ↗
87. Hori K, Matsumoto S (2010) Bacterial adhesion: from mechanism to control. Biochem Eng J 48(3):424–434. https://doi.org/10.1016/j.bej.2009.11.01410.1016/j.bej.2009.11.014 ↗
88. Scarano A, Tari Rexhep S, Leo L, Lorusso F (2022) Wettability of implant surfaces: blood vs autologous platelet liquid (APL). J Mech Behav Biomed Mater. 126 https://doi.org/10.1016/j.jmbbm.2021.10477310.1016/j.jmbbm.2021.104773 ↗
89. Pantaroto HN et al (2021) Sputtered crystalline TiO2 film drives improved surface properties of titanium-based biomedical implants. Mater Sci Eng C Mater Biol Appl. 119 https://doi.org/10.1016/j.msec.2020.11163810.1016/j.msec.2020.111638 ↗
90. Cui H, Wang W, Shi L, Song W, Wang S (2020) Superwettable surface engineering in controlling cell adhesion for emerging bioapplications. Small Methods 4(12):2000573. https://doi.org/10.1002/smtd.20200057310.1002/smtd.202000573 ↗
91. Yuan Y, Hays MP, Hardwidge PR, Kim J (2017) Surface characteristics influencing bacterial adhesion to polymeric substrates. RSC Adv 7(23):14254–14261. https://doi.org/10.1039/c7ra01571b10.1039/c7ra01571b ↗
92. Tamada Y, Ikada Y (1993) Effect of preadsorbed proteins on cell adhesion to polymer surfaces. J Colloid Interface Sci 155(2):334–339. https://doi.org/10.1006/jcis.1993.104410.1006/jcis.1993.1044 ↗
93. Jin X et al (2024) In vitro and in vivo studies on biodegradable Zn porous scaffolds with a drug-loaded coating for the treatment of infected bone defect. Mater Today Bio. 24 https://doi.org/10.1016/j.mtbio.2023.10088510.1016/j.mtbio.2023.100885 ↗
94. Qiang HF et al (2022) Development of biodegradable Zn-Mn-Li and CaP coatings on Zn-Mn-Li alloys and cytocompatibility evaluation for bone graft. Front Bioeng Biotechnol. 10 https://doi.org/10.3389/fbioe.2022.101309710.3389/fbioe.2022.1013097 ↗
95. Tong X et al (2024) In vitro and in vivo studies of a biodegradable Zn-4Ag-0.1Sc alloy with high strength-elongation product, cytocompatibility, osteogenic differentiation, and anti-infection properties for guided bone-regeneration membrane applications. Chem Eng J. 493 https://doi.org/10.1016/j.cej.2024.15276310.1016/j.cej.2024.152763 ↗
96. Zhu Y, Goh C, Shrestha A (2021) Biomaterial properties modulating bone regeneration. Macromol Biosci 21(4):2000365. https://doi.org/10.1002/mabi.20200036510.1002/mabi.202000365 ↗
97. Chandra G, Pandey A (2021) Design approaches and challenges for biodegradable bone implants: a review. Expert Rev Med Devices 18(7):629–647. https://doi.org/10.1080/17434440.2021.193587510.1080/17434440.2021.1935875 ↗
98. Tong X et al (2018) Microstructure, mechanical properties, biocompatibility, and in vitro corrosion and degradation behavior of a new Zn–5Ge alloy for biodegradable implant materials. Acta Biomater 82:197–204. https://doi.org/10.1016/j.actbio.2018.10.01510.1016/j.actbio.2018.10.015 ↗
99. Li HF et al (2015) Development of biodegradable Zn-1X binary alloys with nutrient alloying elements Mg, Ca and Sr. Sci Rep. 5 https://doi.org/10.1038/srep1071910.1038/srep10719 ↗
100. Sikora-Jasinska M, Mostaed E, Mostaed A, Beanland R, Mantovani D, Vedani M (2017) Fabrication, mechanical properties and in vitro degradation behavior of newly developed Zn Ag alloys for degradable implant applications. Mater Sci Eng C Mater Biol Appl 77:1170–1181. https://doi.org/10.1016/j.msec.2017.04.02310.1016/j.msec.2017.04.023 ↗