journal article·2023-08

Simulative and experimental study of metal/polymer interfacial dynamic shear response

Ruizhi Zhang, Jiajin Li, Jijun Ding, Qinqin Wei, Guoqiang Luo, Baozhen Wang, Yi Sun, Jian Zhang, Qiang Shen

Journal of Materials Science· Volume 58· Issue 32
Publisher page

Abstract

The dynamic response experiment has been a difficult point of the metal/polymer interfacial bonding performance testing, in which the metal surface state and the loading condition are key independent variables that should be comprehensively investigated. This work investigates the effect of loading velocity and Al surface porosity on Al/PMMA interfacial dynamic shear bonding performance. Firstly, simulation is applied to predict dynamic response variation trends. Simulation results show that the maximum force (MF) has minor changes with initial bullet velocity (IBV), while the de-bonding displacement (DD) and interface failure work (IFW) decrease obviously with IBV. All three indicators increase smoothly with the area ratio of PMMA interlocks. In experiment, the result plots of the indicators are all discrete, but as a whole, the MF plots could not be distinguished by the variation of IBV, while the plots of DD and NW decrease with IBV, which are consistent with simulation. The dynamic response indicators obtained by simulation and experiment show similar variation trends with their respective independent variables at certain ranges (surface porosity: − 15–20%/dm2, area ratio: 0–0.33) and could be contrasted to evaluate the indicator value differences at full range. By further analysis within MF and DD indicators, the stability of the dynamic interfacial stiffness is discovered at their respective loading velocities, which is similar static loading in past work. The strengthening and weakening mechanisms of Al/PMMA interface are also inferred. This experiment–simulation combined work exhibits a systematic method to predict the dynamic response with the variation of the independent investigating variables at certain ranges, to evaluate the degree of deviation of the experimental plots from simulative ones and to help determine the porosity range where higher dynamic response would be obtained, which would be also applied to other metal/polymer layered system.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Mechanical Behavior of Composites · High-Velocity Impact and Material Behavior · Electronic Packaging and Soldering Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. Zhou Z, Gao X, Zhang Y (2022) Research progress on characterization and regulation of forming quality in laser joining of metal and polymer, and development trends of lightweight automotive applications. Metals (Basel) 12:166610.3390/met12101666 ↗
2. Lambiase F, Scipioni SI, Lee CJ et al (2021) A state-of-the-art review on advanced joining processes for metal-composite and metal-polymer hybrid structures. Materials (Basel) 14:1890. https://doi.org/10.3390/ma1408189010.3390/ma14081890 ↗
3. Annerfors C, Petersson S (2007) Nano molding technology on cosmetic aluminum parts in mobile phones. Division of Production and Materials Engineering, Lund
4. Kajihara Y, Takeuchi A, Kimura F (2023) Direct joining between nano-textured metal and non-crystalline polymer via heating and cooling injection molding. CIRP Ann 72:473–476. https://doi.org/10.1016/j.cirp.2023.04.00410.1016/j.cirp.2023.04.004 ↗
5. Jiao Y, Ma W (2022) Effect of the polymer on the joint strength of polymer/copper hybrids produced by nano-injection molding: comparison of polybutylene terephthalate and polyphenylene sulfide via experimental and computational methods. Mater Today Commun 33:104291. https://doi.org/10.1016/j.mtcomm.2022.10429110.1016/j.mtcomm.2022.104291 ↗
6. Cao D, Malakooti S, Kulkarni VN et al (2021) Nanoindentation measurement of core–skin interphase viscoelastic properties in a sandwich glass composite. Mech Time-Depend Mater 25:353–363. https://doi.org/10.1007/s11043-020-09448-y10.1007/s11043-020-09448-y ↗
7. Cao D, Malakooti S, Kulkarni VN et al (2022) The effect of resin uptake on the flexural properties of compression molded sandwich composites. Wind Energy 25:71–93. https://doi.org/10.1002/we.266110.1002/we.2661 ↗
8. Kuteneva SV, Gladkovsky SV, Vichuzhanin DI, Nedzvetsky PD (2022) Microstructure and properties of layered metal/rubber composites subjected to cyclic and impact loading. Compos Struct 285:115078. https://doi.org/10.1016/j.compstruct.2021.11507810.1016/j.compstruct.2021.115078 ↗
9. Caisso C, Dagorn N, Albouy W et al (2023) Experimental and numerical investigations of a soft projectile impact three-point bending (SPITPB) test for adhesion assessment under dynamic loading. Eur J Mech A Solids 101:105060. https://doi.org/10.1016/j.euromechsol.2023.10506010.1016/j.euromechsol.2023.105060 ↗
10. Wong EH, Rajoo R, Seah SKW et al (2008) Correlation studies for component level ball impact shear test and board level drop test. Microelectron Reliab 48:1069–1078. https://doi.org/10.1016/j.microrel.2008.04.00810.1016/j.microrel.2008.04.008 ↗
11. Santhanakrishnan Balakrishnan V, Obrosov A, Kuke F et al (2019) Influence of metal surface preparation on the flexural strength and impact damage behaviour of thermoplastic FRP reinforced metal laminate made by press forming. Compos Part B Eng 173:106883. https://doi.org/10.1016/j.compositesb.2019.05.09410.1016/j.compositesb.2019.05.094 ↗
12. Mehr ME, Aghamohammadi H, Abbandanak SNH et al (2019) Effects of applying a combination of surface treatments on the mechanical behavior of basalt fiber metal laminates. Int J Adhes Adhes 92:133–141. https://doi.org/10.1016/j.ijadhadh.2019.04.01510.1016/j.ijadhadh.2019.04.015 ↗
13. Brugo TM, Croccolo D, De Agostinis M et al (2023) On the impact strength of adhesive bonded pin-and-collar joints. Int J Adhes Adhes 122:103334. https://doi.org/10.1016/j.ijadhadh.2023.10333410.1016/j.ijadhadh.2023.103334 ↗
14. Yildiz S, Chiu J, Delale F, Elvin N (2022) Characterization of adhesive joints under ballistic shear impact. Int J Adhes Adhes 113:103035. https://doi.org/10.1016/j.ijadhadh.2021.10303510.1016/j.ijadhadh.2021.103035 ↗
15. Li J, Cheng P, Zhang R et al (2022) Easy characterization of the etched Al5052 surfaces and its distinctive data correlation with the Al5052/PMMA bonding performance. Mater Today Commun 32:103983. https://doi.org/10.1016/j.mtcomm.2022.10398310.1016/j.mtcomm.2022.103983 ↗
16. Huang H, Sun M, Wei X et al (2021) Effect of interfacial nanostructures on shear strength of Al-PPS joints fabricated via injection moulding method combined with anodising. Surf Coat Technol 428:127896. https://doi.org/10.1016/j.surfcoat.2021.12789610.1016/j.surfcoat.2021.127896 ↗
17. Balordi M, Cammi A, Santucci de Magistris G, Chemelli C (2019) Role of micrometric roughness on anti-ice properties and durability of hierarchical super-hydrophobic aluminum surfaces. Surf Coat Technol 374:549–556. https://doi.org/10.1016/j.surfcoat.2019.06.00110.1016/j.surfcoat.2019.06.001 ↗
18. Afzali N, Taghvaei E, Moosavi A (2020) A novel and cost-effective method for fabrication of a durable superhydrophobic aluminum surface with self-cleaning properties. Nanotechnology 31:465708. https://doi.org/10.1088/1361-6528/abad5c10.1088/1361-6528/abad5c ↗
19. Peng J, Chen B, Wang Z et al (2020) Surface coordination layer passivates oxidation of copper. Nature 586:390–394. https://doi.org/10.1038/s41586-020-2783-x10.1038/s41586-020-2783-x ↗
20. Cao Q, Guo R, Yang F et al (2021) Research on surface treatment and interfacial bonding technology of copper–polymer direct molding process. Materials (Basel) 14:2712. https://doi.org/10.3390/ma1411271210.3390/ma14112712 ↗
21. Xu D, Yang W, Li X et al (2020) Surface nanostructure and wettability inducing high bonding strength of polyphenylene sulfide-aluminum composite structure. Appl Surf Sci 515:145996. https://doi.org/10.1016/j.apsusc.2020.14599610.1016/j.apsusc.2020.145996 ↗
22. Yang Y, Zhao J, Zhang S et al (2021) Determination of fracture toughness of an adhesive in civil engineering and interfacial damage analysis of carbon fiber reinforced polymer–steel structure bonded joints. Proc Inst Mech Eng Part L J Mater Des Appl 235:2423–2440. https://doi.org/10.1177/1464420721102138510.1177/14644207211021385 ↗
23. Shaikh Mohammad Meiabadi MS, Kazerooni A, Moradi M, Torkamany MJ (2020) Laser assisted joining of St12 to polycarbonate: experimental study and numerical simulation. Optik (Stuttg) 208:164151. https://doi.org/10.1016/j.ijleo.2019.16415110.1016/j.ijleo.2019.164151 ↗
24. Kaiser I, Tan KT (2020) Damage and strength analysis of carbon fiber reinforced polymer and titanium tubular-lap joint using hybrid adhesive design. Int J Adhes Adhes 103:102710. https://doi.org/10.1016/j.ijadhadh.2020.10271010.1016/j.ijadhadh.2020.102710 ↗
25. Ma F, Chen S, Han L et al (2019) Experimental and numerical investigation on the strength of polymer-metal hybrid with laser assisted metal surface treatment. J Adhes Sci Technol 33:1112–1129. https://doi.org/10.1080/01694243.2019.158288810.1080/01694243.2019.1582888 ↗
26. Wang X, Xu T, de Andrade MJ, Rampalli I, Cao D, Haque M, Roy S, Baughman RH, Lu H (2021) The interfacial shear strength of carbon nanotube sheet modified carbon fiber composites. In: Challenges in mechanics of time dependent materials, pp 25–3210.1007/978-3-030-59542-5_4 ↗
27. Carbas RJC, Marques EAS, da Silva LFM (2021) The influence of epoxy adhesive toughness on the strength of hybrid laminate adhesive joints. Appl Adhes Sci 9:1–14. https://doi.org/10.1186/s40563-020-00132-510.1186/s40563-020-00132-5 ↗
28. Hirsch F, Natkowski E, Kästner M (2021) Modeling and simulation of interface failure in metal-composite hybrids. Compos Sci Technol 214:108965. https://doi.org/10.1016/j.compscitech.2021.10896510.1016/j.compscitech.2021.108965 ↗
29. Della PA, Mariani S, Rovitto M et al (2023) Leadframe-epoxy moulding compound adhesion: a micromechanics-driven investigation. In: 2023 24th international conference on thermal, mechanical and multi-physics simulation and experiments in microelectronics and microsystems, EuroSimE 2023, pp 1–7. https://doi.org/10.1109/EuroSimE56861.2023.1010079210.1109/EuroSimE56861.2023.10100792 ↗
30. Kim S, Kim A, Yoo D et al (2021) Enhancement of steel sandwich sheet adhesion using mechanical interlocking structures formed by electrochemical etching. Langmuir 37:6702–6710. https://doi.org/10.1021/acs.langmuir.1c0060110.1021/acs.langmuir.1c00601 ↗
31. Kojima T, Kimura Y, Arikawa S, Notomi M (2021) Evaluation of dynamic fracture toughness of a bonded bi-material interface subject to high-strain-rate shearing using digital image correlation. Eng Fract Mech 241:107391. https://doi.org/10.1016/j.engfracmech.2020.10739110.1016/j.engfracmech.2020.107391 ↗
32. Pu C, Yang X, Zhao H et al (2021) Numerical investigation on crack propagation and coalescence induced by dual-borehole blasting. Int J Impact Eng 157:103983. https://doi.org/10.1016/j.ijimpeng.2021.10398310.1016/j.ijimpeng.2021.103983 ↗
33. Li J, Ding J, Wei J et al (2023) Dynamic response of metal/polymer bilayer composite with optimized surface porosity by experiment and simulation. J Mater Res Technol 24:1626–1637. https://doi.org/10.1016/j.jmrt.2023.03.09710.1016/j.jmrt.2023.03.097 ↗
34. Du Y, Pei P, Suo T, Gao G (2023) Large deformation mechanical behavior and constitutive modeling of oriented PMMA. Int J Mech Sci 257:108520. https://doi.org/10.1016/j.ijmecsci.2023.10852010.1016/j.ijmecsci.2023.108520 ↗
35. Zhang B, Liu Y, Yu H et al (2022) A visco-elastoplastic constitutive model of aircraft polymethylmethacrylate related to strain rate and temperature. Chin J Aeronaut 36:435–445. https://doi.org/10.1016/j.cja.2022.09.00510.1016/j.cja.2022.09.005 ↗
36. Pu C, Yang X, Zhao H et al (2022) Numerical study on crack propagation under explosive loads. Acta Mech Sin 38:421376. https://doi.org/10.1007/s10409-021-09036-x10.1007/s10409-021-09036-x ↗
37. Rudawska A (2019) Surface treatment in bonding technology, chapter 4: degreasing. Elsevier, Amsterdam
38. Joshi S, Fahrenholtz WG, OKeefe MJ (2011) Effect of alkaline cleaning and activation on aluminum alloy 7075–T6. Appl Surf Sci 257:1859–1863. https://doi.org/10.1016/j.apsusc.2010.08.12610.1016/j.apsusc.2010.08.126 ↗
39. Kajihara Y, Tamura Y, Kimura F et al (2018) Joining strength dependence on molding conditions and surface textures in blast-assisted metal-polymer direct joining. CIRP Ann 67:591–594. https://doi.org/10.1016/j.cirp.2018.04.11210.1016/j.cirp.2018.04.112 ↗
40. Zhang X, Ma Q, Dai Y et al (2018) Effects of surface treatments and bonding types on the interfacial behavior of fiber metal laminate based on magnesium alloy. Appl Surf Sci 427:897–906. https://doi.org/10.1016/j.apsusc.2017.09.02410.1016/j.apsusc.2017.09.024 ↗
41. Zhao S, Kimura F, Yamaguchi E et al (2020) Manufacturing aluminum/polybutylene terephthalate direct joints by using hot water–treated aluminum via injection molding. Int J Adv Manuf Technol 107:4637–4644. https://doi.org/10.1007/s00170-020-05364-010.1007/s00170-020-05364-0 ↗
42. Foley RT (1986) Localized corrosion of aluminum alloys: a review. Corrosion 42:277–288. https://doi.org/10.5006/1.358490510.5006/1.3584905 ↗
43. Li J, Liu Z, Zhang R et al (2021) Surface treatment and solvent co-assisted easy direct bonding of polymer/metal. Mater Des 204:109641. https://doi.org/10.1016/j.matdes.2021.10964110.1016/j.matdes.2021.109641 ↗
44. Gu T, Wang Z (2022) A strain rate-dependent cohesive zone model for shear failure of hat-shaped specimens under impact. Eng Fract Mech 259:108145. https://doi.org/10.1016/j.engfracmech.2021.10814510.1016/j.engfracmech.2021.108145 ↗
45. Xu Z, Ding X, Zhang W, Huang F (2017) A novel method in dynamic shear testing of bulk materials using the traditional SHPB technique. Int J Impact Eng 101:90–104. https://doi.org/10.1016/j.ijimpeng.2016.11.01210.1016/j.ijimpeng.2016.11.012 ↗
46. Wang H, Ren C, Wan Y et al (2019) Experimental study on fracture process of sintered Nd–Fe–B magnets during dynamic Brazilian tests. J Magn Magn Mater 471:200–208. https://doi.org/10.1016/j.jmmm.2018.09.08310.1016/j.jmmm.2018.09.083 ↗
47. Acharya S, Mukhopadhyay AK (2014) High strain rate compressive behavior of PMMA. Polym Bull 71:133–149. https://doi.org/10.1007/s00289-013-1050-910.1007/s00289-013-1050-9 ↗
48. Wang J, Zhang Z, Shi R et al (2020) Impact of nanoscale roughness on heat transport across the solid-solid interface. Adv Mater Interfaces 7:1–7. https://doi.org/10.1002/admi.20190158210.1002/admi.201901582 ↗
49. Chen Y, Zhang C (2014) Role of surface roughness on thermal conductance at liquid–solid interfaces. Int J Heat Mass Transf 78:624–629. https://doi.org/10.1016/j.ijheatmasstransfer.2014.07.00510.1016/j.ijheatmasstransfer.2014.07.005 ↗