journal article·2024-02

Influence of laser powder bed fusion process on microstructures and low cycle fatigue performance of Invar 36 alloy

Ye Zhou, Qidong Yang, Rongzheng Huang, Junhan Zhou, Kai Wei, Xujing Yang

Journal of Materials Science· Volume 59· Issue 7
Publisher page

Abstract

The laser powder bed fusion (LPBF) provides a promise process to additively manufacture the Invar 36 alloy, while inevitably generating defects, which significantly weaken the mechanical performances, especially the fatigue resistance. Herein, the Invar 36 alloy was fabricated by LPBF at different process parameters, and the defects, microstructure, mechanical, especially low cycle fatigue (LCF) behavior were systematically characterized and analyzed. Specifically, the insufficient laser energy density leads to solely a slight overlapping between adjacent molten pools, generating a large number of defects. Consequently, the Invar 36 alloy exhibits a poor LCF life (2732cycles), since it fails due to the multiple crack initiation and rapid accumulation of the defects. Besides, the numerous defects lead to a more susceptibility to the plastic strain, inducing the cyclic softening. In contrast, the adequate laser energy density ensures the sufficient overlapping and stable molten pools, resulting in only few pores and favorable microstructures. Accordingly, the fabricated Invar 36 alloy demonstrates the superior LCF life (122777cycles), benefiting from the single crack initiation and stable crack propagation. In addition, the cyclic deformation response shows the cyclic hardening followed by the cyclic softening, due to the formation of the dislocation blocking bands, subsequent dislocation rearrangement as well as the microcrack initiation and propagation.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. Ahadi A, Matsushita Y, Sawaguchi T, Sun Q, Tsuchiya K (2017) Origin of zero and negative thermal expansion in severely-deformed superelastic NiTi alloy. Acta Mater 124:79–92. https://doi.org/10.1016/j.actamat.2016.10.05410.1016/j.actamat.2016.10.054 ↗
2. Qiu C, Adkins NJE, Attallah MM (2016) Selective laser melting of Invar 36: Microstructure and properties. Acta Mater 103:382–395. https://doi.org/10.1016/j.actamat.2015.10.02010.1016/j.actamat.2015.10.020 ↗
3. Zheng JJ, Li CS, He S, Cai B, Song YL (2016) Microstructural and tensile behavior of Fe-36%Ni alloy after cryorolling and subsequent annealing. Mat Sci Eng A 670:275–279. https://doi.org/10.1016/j.msea.2016.06.00410.1016/j.msea.2016.06.004 ↗
4. Wei K, Yang QD, Ling B, Yang XJ, Xie HQ, Qu ZL, Fang DN (2020) Mechanical properties of Invar 36 alloy additively manufactured by selective laser melting. Mat Sci Eng A 772:138799. https://doi.org/10.1016/j.msea.2019.13879910.1016/j.msea.2019.138799 ↗
5. Wegener T, Brenne F, Fischer A, Möller T, Hauck C, Auernhammer S, Niendorf T (2020) On the structural integrity of Fe-36Ni Invar alloy processed by selective laser melting. Addit Manuf. https://doi.org/10.1016/j.addma.2020.10160310.1016/j.addma.2020.101603 ↗
6. Nagayama T, Yamamoto T, Nakamura T (2016) Thermal expansions and mechanical properties of electrodeposited Fe–Ni alloys in the Invar composition range. Electrochimi Acta 205:178–187. https://doi.org/10.1016/j.electacta.2016.04.08910.1016/j.electacta.2016.04.089 ↗
7. Yuan S, Chua CK, Zhou K (2019) 3D-printed mechanical metamaterials with high energy absorption. Adv Mater Technol-US. https://doi.org/10.1002/admt.20180041910.1002/admt.201800419 ↗
8. Askari M, Hutchins DA, Thomas PJ, Astolfi L, Watson RL, Abdi M, Ricci M, Laureti S, Nie L, Freear S, Wildman R, Tuck C, Clarke M, Woods E, Clare AT (2020) Additive manufacturing of metamaterials: a review. Addit Manuf 36:101562. https://doi.org/10.1016/j.addma.2020.10156210.1016/j.addma.2020.101562 ↗
9. Zhan X, Meng Y, Zhou J, Qi C, Zhang C, Gu D (2018) Quantitative research on microstructure and thermal physical mechanism in laser melting deposition for Invar alloy. J Manuf Process 31:221–231. https://doi.org/10.1016/j.jmapro.2017.11.01810.1016/j.jmapro.2017.11.018 ↗
10. Kim SH, Choi SG, Choi WK, Lee ES (2017) Surface characteristics of Invar alloy according to micro-pulse electrochemical machining. Mater Tehnol 51(5):745–749. https://doi.org/10.17222/mit.2016.187.10.17222/mit.2016.187 ↗
11. Yakout M, Elbestawi MA, Veldhuis SC (2018) A study of thermal expansion coefficients and microstructure during selective laser melting of Invar 36 and stainless steel 316L. Addit Manuf 24:405–418. https://doi.org/10.1016/j.addma.2018.09.03510.1016/j.addma.2018.09.035 ↗
12. Jasthi BK, Arbegast WJ, Howard SM (2009) Thermal Expansion Coefficient and Mechanical Properties of Friction Stir Welded Invar (Fe-36%Ni). J Mater Eng Perform 18(7):925–934. https://doi.org/10.1007/s11665-008-9320-710.1007/s11665-008-9320-7 ↗
13. Shen L, Wang X, Li Z, Wei K, Wang Z (2022) Elastic properties of an additive manufactured three-dimensional vertex-based hierarchical re-entrant structure. Mater Des 216:110527. https://doi.org/10.1016/j.matdes.2022.11052710.1016/j.matdes.2022.110527 ↗
14. Wang Z, Lei Z, Li Z, Yuan K, Wang X (2021) Mechanical reinforcement mechanism of a hierarchical Kagome honeycomb. Thin Wall Struct 167:108235. https://doi.org/10.1016/j.tws.2021.10823510.1016/j.tws.2021.108235 ↗
15. Herzog D, Seyda V, Wycisk E, Emmelmann C (2016) Additive manufacturing of metals. Acta Mater 117:371–392. https://doi.org/10.1016/j.actamat.2016.07.01910.1016/j.actamat.2016.07.019 ↗
16. Zhang YB, Yao S, Hong X, Wang ZG (2017) A modified Johnson-Cook model for 7N01 aluminum alloy under dynamic condition. J Cent South Univ 24(11):2550–2555. https://doi.org/10.1007/s11771-017-3668-510.1007/s11771-017-3668-5 ↗
17. Liu YR, Ding R, Han Y, Gao ZJ, Ma T, Wang H, Guo QY, Ma ZQ (2023) Preparation of high-performance SA508 Grade 3 steel by laser powder bed fusion: role of high cooling rate on microstructure and mechanical properties. J Mater Sci 58:5921–5932. https://doi.org/10.1007/s10853-023-08381-y10.1007/s10853-023-08381-y ↗
18. Liu K, Liu JL, Wang Z (2020) A damage threshold prediction model of CFRP panel by hail impact based on delamination mechanism. Eng Fract Mech 239:107282. https://doi.org/10.1016/j.engfracmech.2020.10728210.1016/j.engfracmech.2020.107282 ↗
19. Manlay MR, Garandet J, Bacchetta G, Soulier M, Flament C (2023) On the elaboration of composite AlSi7Mg0.6/SiC powders and parts by laser powder bed fusion. J Mater Sci 58:5269–5286. https://doi.org/10.1007/s10853-023-08249-110.1007/s10853-023-08249-1 ↗
20. Wang R, Gu D, Zhang H, Guo M (2022) High temperature oxidation behavior of laser powder bed fusion printed WC/Inconel 718 composites. J Mater Sci 57:14119–14134. https://doi.org/10.1007/s10853-022-07520-110.1007/s10853-022-07520-1 ↗
21. Yakout M, Cadamuro A, Elbestawi MA, Veldhuis SC (2017) The selection of process parameters in additive manufacturing for aerospace alloys. Int J Adv Manuf Tech 92:2081–2098. https://doi.org/10.1007/s00170-017-0280-710.1007/s00170-017-0280-7 ↗
22. Yakout M, Elbestawi MA, Veldhuis SC (2019) Density and mechanical properties in selective laser melting of Invar 36 and stainless steel 316L. J Mater Process Tech 266:397–420. https://doi.org/10.1016/j.jmatprotec.2018.11.00610.1016/j.jmatprotec.2018.11.006 ↗
23. Yakout M, Elbestawi M, Fang Q (2021) In-situ monitoring and detection of spatter agglomeration and delamination during laser-based powder bed fusion of Invar 36. Opt Laser Technol 136:106741. https://doi.org/10.1016/j.optlastec.2020.10674110.1016/j.optlastec.2020.106741 ↗
24. Harrison NJ, Todd I, Mumtaz K (2017) Thermal expansion coefficients in Invar processed by selective laser melting. J Mater Sci 52:10517–10525. https://doi.org/10.1007/s10853-017-1169-410.1007/s10853-017-1169-4 ↗
25. Asgari H, Salarian M, Ma H, Olubamiji A, Vlasea M (2018) On thermal expansion behavior of invar alloy fabricated by modulated laser powder bed fusion. Mater Des 160:895–905. https://doi.org/10.1016/j.matdes.2018.10.02510.1016/j.matdes.2018.10.025 ↗
26. Yang Q, Wei K, Yang X, Xie H, Qu Z, Fang D (2020) Microstructures and unique low thermal expansion of Invar 36 alloy fabricated by selective laser melting. Mater Charact 166:110409. https://doi.org/10.1016/j.matchar.2020.11040910.1016/j.matchar.2020.110409 ↗
27. Qiu C, Liu Y, Liu H (2021) Influence of addition of TiAl particles on microstructural and mechanical property development in Invar 36 processed by laser powder bed fusion. Addit Manuf 48:102457. https://doi.org/10.1016/j.addma.2021.10245710.1016/j.addma.2021.102457 ↗
28. Liu H, Pan X, Sun P, Liu Y, Qiu C (2022) Influence of addition of Ti particles and processing condition on microstructure and properties of selectively laser-melted invar 36 alloy. 3D Print Addit Manuf. https://doi.org/10.1089/3dp.2022.001610.1089/3dp.2022.0016 ↗
29. Oh DJ, Lee JM, Kim MH (2014) Fatigue strength assessment of Invar alloy weld joints using the notch stress approach. Eng Fail Anal 42:87–99. https://doi.org/10.1016/j.engfailanal.2014.04.00310.1016/j.engfailanal.2014.04.003 ↗
30. Oh DJ, Kim NK, Song SW, Kim YD, Kim MH (2018) Investigation of fatigue performance for new membrane-type LNG CCS at cryogenic temperature. Mar Struct 62:90–105. https://doi.org/10.1016/j.marstruc.2018.08.00510.1016/j.marstruc.2018.08.005 ↗
31. Vijayanandh R, Raj Kumar G, Senthil Kumar M, Karthick M, Ramganesh T (2016) Fatigue life estimation of aircraft engine compressor with suitable material selection (analytical approach for compressor lifetime). In: International conference on intelligent systems and control (ISCO), pp 1–5. https://doi.org/10.1109/ISCO.2016.772705510.1109/ISCO.2016.7727055 ↗
32. Zhang C, Zhou Y, Wei K, Yang Q, Zhou J, Zhou H, Zhang X, Yang X (2023) High cycle fatigue behaviour of Invar 36 alloy fabricated by laser powder bed fusion. Virtual Phys Prototy 18(1):e2190901. https://doi.org/10.1080/17452759.2023.219090110.1080/17452759.2023.2190901 ↗
33. Akgul B, Kul M, Erden F (2023) The puzzling thermal expansion behavior of invar alloys: a review on process-structure-property relationship. Crit Rev Solid State. https://doi.org/10.1080/10408436.2023.217097510.1080/10408436.2023.2170975 ↗
34. ASTM international, (2016) ASTM E8/E8M-16a: Standard Test Methods for Tension Testing of Metallic Materials. ASTM international
35. ASTM international, (2007) ASTM E466: standard practice for conducting force controlled constant amplitude axial fatigue tests of metallic materials. ASTM international
36. Leung CLA, Marussi S, Towrie M, Atwood RC, Withers PJ, Lee PD (2019) The effect of powder oxidation on defect formation in laser additive manufacturing. Acta Mater 166:294–305. https://doi.org/10.1016/j.actamat.2018.12.02710.1016/j.actamat.2018.12.027 ↗
37. Guo Q, Qu M, Escano LI, Hojjatzadeh SMH, Young Z, Fezzaa K, Chen L (2022) Revealing melt flow instabilities in laser powder bed fusion additive manufacturing of aluminum alloy via in-situ high-speed X-ray imaging. Int J Mach Tool Manu 175:103861. https://doi.org/10.1016/j.ijmachtools.2022.10386110.1016/j.ijmachtools.2022.103861 ↗
38. Khairallah SA, Anderson AT, Rubenchik A, King WE (2016) Laser powder-bed fusion additive manufacturing: physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones. Acta Mater 108:36–45. https://doi.org/10.1016/j.actamat.2016.02.01410.1016/j.actamat.2016.02.014 ↗
39. Liu W, Chen C, Shuai S, Zhao R, Liu L, Wang X, Hu T, Xuan W, Li C, Yu J (2020) Study of pore defect and mechanical properties in selective laser melted Ti6Al4V alloy based on X-ray computed tomography. Mat Sci Eng A 797:139981. https://doi.org/10.1016/j.msea.2020.13998110.1016/j.msea.2020.139981 ↗
40. Pham MS, Dovgyy B, Hooper PA, Gourlay CM, Piglione A (2020) The role of side-branching in microstructure development in laser powder-bed fusion. Nat Commun 11(1):749. https://doi.org/10.1038/s41467-020-14453-310.1038/s41467-020-14453-3 ↗
41. Ji Y, Dong C, Kong D, Li X (2020) Design materials based on simulation results of silicon induced segregation at AlSi10Mg interface fabricated by selective laser melting. J Mater Sci Technol 46:145–155. https://doi.org/10.1016/j.jmst.2020.01.03710.1016/j.jmst.2020.01.037 ↗
42. Chen C, Ma B, Liu B, He J, Xue H, Zuo Y, Li X (2019) Refinement mechanism and physical properties of arc melted invar alloy with different modifiers. Mater Chem Phys 227:138–147. https://doi.org/10.1016/j.matchemphys.2019.02.00610.1016/j.matchemphys.2019.02.006 ↗
43. Cui X, Zhang S, Wang C, Zhang CH, Chen J, Zhang JB (2020) Microstructure and fatigue behavior of a laser additive manufactured 12CrNi2 low alloy steel. Mat Sci Eng A 772:138685. https://doi.org/10.1016/j.msea.2019.13868510.1016/j.msea.2019.138685 ↗
44. Bayati P, Jahadakbar A, Barati M, Nematollahi M, Saint-Sulpice L, Haghshenas M, Chirani SA, Mahtabi MJ, Elahinia M (2020) Toward low and high cycle fatigue behavior of SLM-fabricated NiTi: considering the effect of build orientation and employing a self-heating approach. Int J Mech Sci 185:105878. https://doi.org/10.1016/j.ijmecsci.2020.10587810.1016/j.ijmecsci.2020.105878 ↗
45. Uzan NE, Shneck R, Yeheskel O, Frage N (2017) Fatigue of AlSi10Mg specimens fabricated by additive manufacturing selective laser melting (AM-SLM). Mat Sci Eng A 704:229–237. https://doi.org/10.1016/j.msea.2017.08.02710.1016/j.msea.2017.08.027 ↗
46. Sarkar S, Kumar CS, Kumar AN (2017) Effect of mean stresses on mode of failures and fatigue life of selective laser melted stainless steel. Mat Sci Eng A 700:92–106. https://doi.org/10.1016/j.msea.2017.05.11810.1016/j.msea.2017.05.118 ↗
47. Peng X, Wu S, Qian W, Bao J, Hu Y, Zhan Z, Guo G, Withers PJ (2022) The potency of defects on fatigue of additively manufactured metals. Int J Mech Sci 221:107185. https://doi.org/10.1016/j.ijmecsci.2022.10718510.1016/j.ijmecsci.2022.107185 ↗
48. Zhang Y, Li X, Yuan S, Sun R, Sakai T, Lashari MI, Hamid U, Li W (2022) High-cycle-fatigue properties of selective-laser-melted AlSi10Mg with multiple building directions. Int J Mech Sci 224:107336. https://doi.org/10.1016/j.ijmecsci.2022.10733610.1016/j.ijmecsci.2022.107336 ↗
49. Wang X, Xu CL, Zhai AS, Liu M, Huang X, Tian K, Luo XK, Liu CG, Tang ZH, Zhao ZY (2023) Effect of surface stress concentration control and surface material strengthening on the fatigue performance of shot-peened single-crystal superalloy. J Alloy Compd 933:167796. https://doi.org/10.1016/j.jallcom.2022.16779610.1016/j.jallcom.2022.167796 ↗
50. Edwards P, Ramulu M (2014) Fatigue performance evaluation of selective laser melted Ti–6Al–4V. Mat Sci Eng A 598:327–337. https://doi.org/10.1016/j.msea.2014.01.04110.1016/j.msea.2014.01.041 ↗
51. Li P, Warner D, Fatemi A, Phan N (2016) Critical assessment of the fatigue performance of additively manufactured Ti–6Al–4V and perspective for future research. Int J Fatigue 85:130–143. https://doi.org/10.1016/j.ijfatigue.2015.12.00310.1016/j.ijfatigue.2015.12.003 ↗
52. Järvenpää A, Jaskari M, Man J, Karjalainen LP (2017) Stability of grain-refined reversed structures in a 301LN austenitic stainless steel under cyclic loading. Mat Sci Eng A 703:280–292. https://doi.org/10.1016/j.msea.2017.07.03310.1016/j.msea.2017.07.033 ↗
53. Zhang Z, Koyama M, Wang MM, Tsuzaki K, Tasan CC, Noguchi H (2018) Microstructural mechanisms of fatigue crack non-propagation in TRIP-maraging steels. Int J Fatigue 113:126–136. https://doi.org/10.1016/j.ijfatigue.2018.04.01310.1016/j.ijfatigue.2018.04.013 ↗
54. Hilditch T, Beladi H, Hodgson P, Stanford N (2012) Role of microstructure in the low cycle fatigue of multi-phase steels. Mat Sci Eng A 534:288–296. https://doi.org/10.1016/j.msea.2011.11.07110.1016/j.msea.2011.11.071 ↗
55. Hilditch TB, Timokhina IB, Robertson LT, Pereloma EV, Hodgson PD (2009) Cyclic deformation of advanced high-strength steels: mechanical behavior and microstructural analysis. Metall Mater Trans A 40(2):342–353. https://doi.org/10.1007/s11661-008-9732-x10.1007/s11661-008-9732-x ↗
56. Maierhofer J, Pippan R, Gänser HP (2014) Modified NASGRO equation for physically short cracks. Int J Fatigue 59:200–207. https://doi.org/10.1016/j.ijfatigue.2013.08.01910.1016/j.ijfatigue.2013.08.019 ↗
57. Jiménez M, Ludwig W, Gonzalez D, Molina-Aldareguia JM (2019) The role of slip transfer at grain boundaries in the propagation of microstructurally short fatigue cracks in Ni-based superalloys. Scripta Mater 162:261–265. https://doi.org/10.1016/j.scriptamat.2018.11.00810.1016/j.scriptamat.2018.11.008 ↗
58. Bai C, Lan L, Xin R, Gao S, He B (2022) Microstructure evolution and cyclic deformation behavior of Ti-6Al-4 V alloy via electron beam melting during low cycle fatigue. Int J Fatigue 159:106784. https://doi.org/10.1016/j.ijfatigue.2022.10678410.1016/j.ijfatigue.2022.106784 ↗
59. Vinogradov A, Hashimoto S, Kopylov VI (2003) Enhanced strength and fatigue life of ultra-fine grain Fe–36Ni Invar alloy. Mat Sci Eng A 355(1–2):277–285. https://doi.org/10.1016/S0921-5093(03)00082-010.1016/S0921-5093(03)00082-0 ↗