journal article·2022-01

Effect of silicon powder-modified tabular alumina aggregates on the mechanical properties and microstructures of carbon-bonded alumina refractories

Xiaoyuan Han, Kai Shi, Shihang Ma, Yi Xia, Yang Liu, Jianzhao Shang

Journal of Materials Science· Volume 57· Issue 2
Publisher page

Abstract

Carbon-bonded alumina (Al2O3–C) refractories were fabricated using unmodified (3–1, 1–0, and 0.045 mm) and Si powder-modified tabular alumina aggregates (3–1 mm) as raw materials, in addition to Si powder, ultra-fine α–Al2O3 powder, and carbon black as fines, and a thermosetting phenolic resin as the binder. The microstructures and phase compositions of the samples were analyzed by scanning electron microscopy and X-ray diffraction. After the mixing and wearing test, the Si powder-modified tabular alumina aggregates exhibited a low Si powder dropping ratio, thereby meeting the requirements to prepare Al2O3–C refractories. The addition of Si powder-modified tabular alumina aggregates to the material had little effect on the thermal shock resistance of the Al2O3–C refractory and was beneficial to improving the cold modulus of rupture of the material. Since the surface of the added modified aggregate was not dense, diffusion and mass transfer were promoted during the oxidation process, thereby leading to a slight decrease in the oxidation resistance of the material. The introduction of Si powder-modified tabular alumina aggregates increased the amount of Si powder particles surrounding the aggregates, resulting in the in situ generation of additional SiC fibers during high temperature heat treatment. Ultimately, this strengthened the interfacial bonding between the matrix and the aggregates. In addition, compared with the hot modulus of rupture (HMOR) of sample S0 (containing 50 wt.% tabular alumina aggregates), the HMOR of sample S2 (containing 51 wt.% modified tabular alumina aggregates with 1 wt.% Si powder coating) was 30% higher.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Advanced materials and composites · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. Zhong XC (2008) Progress in research and development of refractory oxide-nonoxide composites. China’s Refract 17:1–5. https://doi.org/10.3969/j.issn.1004-4493.2008.02.00110.3969/j.issn.1004-4493.2008.02.001 ↗
2. Shi K, Xia Y (2018) Evolution of material systems of slide gates for steelmaking. Refractories 52:230–236. https://doi.org/10.3969/j.issn.1001-1935.2018.03.01910.3969/j.issn.1001-1935.2018.03.019 ↗
3. Ban JJ, Zhou CJ, Feng L, Jia QL, Liu XH, Hu JH (2020) Preparation and application of ZrB2–SiCw composite powder for corrosion resistance improvement in Al2O3–ZrO2–C slide plate materials. Ceram Int 46:9817–9825. https://doi.org/10.1016/j.ceramint.2019.12.25510.1016/j.ceramint.2019.12.255 ↗
4. Shi K, Zhong XC (2007) Properties and application of Al–Si metal bonded Al2O3–C slide plate. Refractories 41:205–207. https://doi.org/10.3969/j.issn.1001-1935.2007.03.01210.3969/j.issn.1001-1935.2007.03.012 ↗
5. Gu Q, Ma T, Zhao F, Jia QL, Liu XX, Liu GQ, Li HX (2020) Enhancement of the thermal shock resistance of MgO–C slide plate materials with the addition of Nano–ZrO2 modified magnesia aggregates. J Alloys Compd 847:156339. https://doi.org/10.1016/j.jallcom.2020.15633910.1016/j.jallcom.2020.156339 ↗
6. Wang QG, Li YW, Sang SB, Jin SL (2018) Enhanced mechanical properties of Al2O3–C refractories with silicon hybridized expanded graphite. Mater Sci Eng A 709:160–171. https://doi.org/10.1016/j.msea.2017.10.04610.1016/j.msea.2017.10.046 ↗
7. Behera SK, Mishra B (2015) Strengthening of Al2O3–C slide gate plate refractories with expanded graphite. Ceram Int A 41:4254–4259. https://doi.org/10.1016/j.ceramint.2014.11.09210.1016/j.ceramint.2014.11.092 ↗
8. Liao N, Li YW, Sang SB (2017) Effects of silicon and microsilica additive on microstructure and mechanical properties of Al2O3–C multi-walled carbon nanotubes refractories. J Chinese Ceram Soc 45:433–440
9. Wan QF, Yin HF, Tang Y, Yuan HD, Ren XH, Gao K, Xin YL, Liu YC (2015) Effect of aggregate on aggregate/spinel matrix bonding interface and mechanical performance of lightweight spinel-bonded refractory. Ceram Int A 46:18362–18365. https://doi.org/10.1016/j.ceramint.2020.04.09510.1016/j.ceramint.2020.04.095 ↗
10. Wang HF, Bi YB, Zhou NS, Zhang HJ (2016) Preparation and strength of SiC refractories with in situ beta-SiC whiskers as bonding phase. Ceram Int A 42:727–733. https://doi.org/10.1016/j.ceramint.2015.08.17210.1016/j.ceramint.2015.08.172 ↗
11. Zhu BQ, Zhu YN, Lin XC, Zhao F (2013) Effect of ceramic bonding phases on the thermo-mechanical properties of Al2O3–C refractories. Ceram Int 39:6069–6076. https://doi.org/10.1016/j.ceramint.2013.01.02410.1016/j.ceramint.2013.01.024 ↗
12. Chen XY, Zhang Q, Zhou Y, Qin YM, Liu XH, Jia QL (2018) Synthesis of bamboo-like 3C–SiC nanowires with good luminescent property via nano–ZrO2 catalyzed chemical vapor deposition technique. Ceram Int 44:22890–22896. https://doi.org/10.1016/j.ceramint.2013.01.02410.1016/j.ceramint.2013.01.024 ↗
13. Liu ZL, Deng CJ, Yu C, Wang X, Ding J, Zhu HX (2018) Preparation of in situ grown silicon carbide whiskers onto graphite for application in Al2O3–C refractories. Ceram Int 44:13944–13950. https://doi.org/10.1016/j.ceramint.2018.04.24310.1016/j.ceramint.2018.04.243 ↗
14. Deng X, Li XC, Zhu BQ, Chen PG (2015) In-situ synthesis mechanism of plate-shaped β–SiAlON and its effect on Al2O3–C refractory properties. Ceram Int 41:14376–14382. https://doi.org/10.1016/j.ceramint.2018.04.24310.1016/j.ceramint.2018.04.243 ↗
15. Yin CF, Li XC, Chen PG, Zhu BQ (2019) Thermo-mechanical properties of Al2O3–C refractories with in situ synthesized non-oxide bonding phases. Ceram Int 45:7427–7436. https://doi.org/10.1016/j.ceramint.2019.01.03210.1016/j.ceramint.2019.01.032 ↗
16. Ma SH, Shi K, Xia Y (2020) Effect of modified tabular alumina aggregates on mechanical properties and microstructure of Al2O3–Al–C material. Ceram Int 46:9773–9779. https://doi.org/10.1016/j.ceramint.2019.12.24910.1016/j.ceramint.2019.12.249 ↗
17. GB/T 2997–2015 (2015) Test method for bulk density,apparent porosity and true porosity of dense shaped refractory products. https://d.wanfangdata.com.cn/standard/ChRTdGFuZGFyZE5ld1MyMDIxMDkwMhIOR0IvVCAyOTk3LTIwMTUaCGRzZDc0bWUx
18. GB/T 3001–2017 (2017) Refractory products-Determination of modulus of rupture at ambient temperature. https://d.wanfangdata.com.cn/standard/ChRTdGFuZGFyZE5ld1MyMDIxMDkwMhIOR0IvVCAzMDAxLTIwMTcaCHQ5cXBybGRn
19. GB/T 3002–2017 (2017) Refractory products-Determination of modules of rupture at elevated temperatures. https://d.wanfangdata.com.cn/standard/ChRTdGFuZGFyZE5ld1MyMDIxMDkwMhIOR0IvVCAzMDAyLTIwMTcaCHZ3eDNvNjFp
20. Chen ZY (2005) Chemical thermodynamics of refractories. Metallurgical Industry Press, Beijing
21. Yamaguchi A (1993) Practical thermodynamics and its application in high temperature ceramics. Wuhan Industrial University Press, Wuhan
22. Wu J, Bu NJ, Li HB, Zhen Q (2017) Effect of B4C on the properties and microstructure of Al2O3–SiC–C based trough castable refractories. Ceram Int 43:1402–1409. https://doi.org/10.1016/j.ceramint.2016.10.10110.1016/j.ceramint.2016.10.101 ↗
23. Zhang ZY, Yan W, Li N, Schafföner S, Zhou WY, Chen Z, Wei JW (2020) Mullite-corundum gas-permeable refractories reinforced by in-situ formed SiC whiskers. Ceram Int 46:25155–25163. https://doi.org/10.1016/j.ceramint.2020.06.30210.1016/j.ceramint.2020.06.302 ↗
24. An JC, Ge TZ, Xu EX, Zhao F, Liu XH (2019) Preparation and properties of mullite-SiC-O’-SiAlON composites for application in cement kiln. Ceram Int 46:15456–15463. https://doi.org/10.1016/j.ceramint.2020.03.09010.1016/j.ceramint.2020.03.090 ↗