journal article·2021-06

The effect of thickness on the performance of (K1/4Ta3/4)xSn1-xO2-based humidity sensor

X. J. Xie, R. J. Si, J. Zheng, C. C. Wang

Journal of Materials Science· Volume 56· Issue 16
Publisher page

Abstract

In this paper, (K1/4Ta3/4)xSn1-xO2 (KTSO, with x = 0, 0.01, 0.02, and 0.05) powders were prepared by solid-state reaction method and used as materials for humidity sensing. The method of saturated salt solution is used to study the sensing performances of the KTSO sensors in the relative humidity (RH) range of 12%–94%. The results show that the sensor based on x = 0.05 sample with the thickness is 62.41 μm and shows the best performances, including a high humidity response of 74.39 pF/%RH, fast recovery time of 5 s (within 5 min), good stability and repeatability. In addition, we found that the humidity response can be easily adjusted by a small dc bias. Oxygen vacancy and ion defects are believed to be the key factors of humidity sensing effect related to doping level; a series of structural coefficients, such as crystallite size, specific surface area, and micro-strain stress, are argued to the factors of the effect related to thickness.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Gas Sensing Nanomaterials and Sensors · Analytical Chemistry and Sensors · Acoustic Wave Resonator Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. Kano S, Kim K, Fujii M (2017) Fast-response and flexible nanocrystal-based humidity sensor for monitoring human respiration and water evaporation on skin. ACS Sensors 2:828–83310.1021/acssensors.7b00199 ↗
2. Kulwicki BM (1991) Humidity sensors. J Am Ceram Soc 74:697–70810.1111/j.1151-2916.1991.tb06911.x ↗
3. Blank TA, Eksperiandova LP, Belikov KN (2018) Recent trends of ceramic humidity sensors development: a review. Sens Actuators B Chem 228:416–44210.1016/j.snb.2016.01.015 ↗
4. Chen Z, Lu Z (2005) Humidity sensors: a review of materials and mechanisms. Sens Lett 3:274–29510.1166/sl.2005.045 ↗
5. Sikarwar S, Yadav BC (2015) Opto-electronic humidity sensor: a review. Sens Actuators A Phys 233:54–7010.1016/j.sna.2015.05.007 ↗
6. Lee CY, Lee GB (2005) Humidity sensors: a review. Sens Lett 3:1–1510.1166/sl.2005.001 ↗
7. Farahani H, Wagiran R, Hamidon MN (2014) Humidity sensors principle, mechanism, and fabrication technologies: a comprehensive review. Sensors 14:7881–793910.3390/s140507881 ↗
8. Zhao YL, Yang B, Liu JQ (2018) Effect of interdigital electrode gap on the performance of SnO2-modified MoS2 capacitive humidity sensor. Sens Actuators B Chem 271:256–26310.1016/j.snb.2018.05.084 ↗
9. Takeda S (1999) Electrode structure and heat treatment effects on stabilization of capacitive humidity sensor with plasma-polymerized thin film. Jpn J Appl Phys 38:90910.1143/JJAP.38.909 ↗
10. Bearzotti A (2008) Influence of metal electrodes on the response of humidity sensors coated with mesoporous silica. J Phys D Appl Phys 41:01510510.1088/0022-3727/41/1/015105 ↗
11. Ahn HY, Kim JG, Gong MS (2012) Preparation of flexible resistive humidity sensors with different electrode gaps by screen printing and their humidity-sensing properties. Macromol Res 20:174–18010.1007/s13233-012-0085-3 ↗
12. Roslan NA, Bakar AA, Bawazeer TM, Alsoufi MS, Alsenany N, Majid WHA, Supangat A (2019) Enhancing the performance of vanadyl phthalocyanine-based humidity sensor by varying the thickness. Sens Actuators B Chem 279:148–15610.1016/j.snb.2018.09.109 ↗
13. Pongampai S, Pengpad P, Meananeatra R, Atiwongsangthong N, Muanghlua R (2020 8th) Study of nitride thickness on sensitivity IDEs humidity sensor based on graphene oxide sensing. International Electrical Engineering Congress (iEECON).10.1109/iEECON48109.2020.229557 ↗
14. Le XH, Liu YH, Peng L, Pang JT, Xu Z, Gao C, Xie J (2019) Surface acoustic wave humidity sensors based on uniform and thickness controllable graphene oxide thin films formed by surface tension. Microsyst Nanoeng 5:3610.1038/s41378-019-0075-0 ↗
15. Lo Presti D, Massaroni C, Piemonte V, Saccomandie P, D’Amato R, Caponero MA, Schena E (2019) Agar-coated fiber bragg grating sensor for relative humidity measurements: influence of coating thickness and polymer concentration. IEEE Sensors J 19:3335–334210.1109/JSEN.2019.2892900 ↗
16. Dipak LG, Sandeep AA, Balasaheb MP, Sanjaykumar ND, Ratan YB (2018) Effect of film thickness on humidity sensing of spray deposited TiO2 thin films. Mater Res Express 6:02640210.1088/2053-1591/aae970 ↗
17. Mathew J, Semenova Y, Farrell G (2013) Effect of coating thickness on the sensitivity of a humidity sensor based on an Agarose coated photonic crystal fiber interferometer. Opt Express 21:6313–632010.1364/OE.21.006313 ↗
18. Ghosal S, Dutta K, Bhattacharyya P (2020) Understanding the improved vapor sensor device performance of dual surface engineered WO3 nanospheres using semi-quantitative energy band model. IEEE Electr Device Lett 41:912–91510.1109/LED.2020.2991085 ↗
19. Torres DL, Elosua C, Villatoro J, Zubia J, Rothhardt M, Schuster K, Arregui FJ (2017) Enhancing sensitivity of photonic crystal fiber interferometric humidity sensor by the thickness of SnO2 thin films. Sens Actuators B Chem 251:1059–106710.1016/j.snb.2017.05.125 ↗
20. KhijwaniaIII SK, Srinivasan KL, Prasad SJ (2005) Performance optimized optical fiber sensor for humidity measurement. Opt Eng 44:03440110.1117/1.1870753 ↗
21. Liang JG, Kim ES, Wang C, Cho MY, Oh JM, Kim NY (2018) Thickness effects of aerosol deposited hygroscopic films on ultra-sensitive humidity sensors. Sens Actuators B Chem 265:632–64310.1016/j.snb.2018.03.093 ↗
22. Si RJ, Li TY, Sun J, Wang J, Wang ST, Zhu GB, Wang CC (2019) Humidity sensing behavior and its influence on the dielectric properties of (In+Nb) co-doped TiO2 ceramics. J Mater Sci 54:14645–1465310.1007/s10853-019-03945-3 ↗
23. Li TY, Si RJ, Sun J, Wang ST, Wang J, Ahmed R, Zhu GB, Wang CC (2019) Giant and controllable humidity sensitivity achieved in (Na+Nb) co-doped rutile TiO2. Sens Actuators B Chem 293:151–15810.1016/j.snb.2019.05.019 ↗
24. Wang J, Guo YM, Wang ST, Tong L, Sun J, Zhu GB, Wang CC (2019) The effect of humidity on the dielectric properties of (In+Nb) co-doped SnO2 ceramics. J Eur Ceram Soc 39:323–32910.1016/j.jeurceramsoc.2018.09.040 ↗
25. Wang D, Lou YL, Wang R, Wang PP, Zheng XJ, Zhang Y, Jiang N (2015) Humidity sensor based on Ga2O3 nanorods doped with Na+ and K+ from GaN powder. Ceram Int 41:14790–1479710.1016/j.ceramint.2015.07.211 ↗
26. Li H, Fan HQ, Liu ZY, Zhang JH, Wen Y, Lu JC, Jiang XB, Chen GY (2018) Highly sensitive humidity sensor based on lithium stabilized Na-β"-alumina: dc and ac analysis. Sens Actuators B Chem 255:1445–145410.1016/j.snb.2017.08.137 ↗
27. Chen J, Li Y, Wang Y, Yun J, Cao D (2004) Preparation and characterization of zinc sulfide nanoparticles under high-gravity environment. Mat Res Bull 39:185–19410.1016/j.materresbull.2003.10.017 ↗
28. Zhang J, Xiao X, Nan J (2010) Hydrothermal-hydrolysis synthesis and photocatalytic properties of nano TiO2 with an adjustable crystalline size. J Hazardous Mat 176:617–62210.1016/j.jhazmat.2009.11.074 ↗
29. Al-Sehemi AG, Al-Assiri MS, Kalam A, Zafar Q, Azmer MI, Sulaiman K, Ahmad Z (2016) Sensing performance optimization by tuning surface morphology of organic (D-π-A) dye based humidity sensor. Sens Actuators B Chem 231:30–3710.1016/j.snb.2016.03.004 ↗
30. Azmer MI, Ahmad Z, Sulaiman K, Touati F, Bawazeer TM, Alsoufi MS (2017) VOPcPhO:P3HT composite micro-structures with nano-porous surface morphology. Appl Surf Sci 399:426–43110.1016/j.apsusc.2016.12.103 ↗
31. Zhang Y, Wu J, Zhang Y, Guo W, Ruan S (2014) Characterization and humidity sensing properties of the sensor based on Na2Ti3O7 nanotubes. J Nanosci Nanotechnol 14:4303–430710.1166/jnn.2014.8038 ↗
32. Wu J, Sun YM, Wu Z, Li X, Wang N, Tao K, Wang GP (2019) Carbon nanocoil-based fast-response and flexible humidity sensor for multifunctional applications. ACS Appl Mater Interfaces 11:4242–425110.1021/acsami.8b18599 ↗
33. Agarwal S, Sharma GL (2002) Humidity sensing properties of (Ba, Sr)TiO3 thin films grown by hydrothermai-electrochemical method. Sens Actuators B Chem 8:205–21110.1016/S0925-4005(02)00109-0 ↗
34. Tao B, Zhang J, Miao F, Li H, Wan L, Wang Y (2009) Capacitive humidity sensors based on Ni/SiNWs nanocomposites. Sens Actuators B Chem 136:144–15010.1016/j.snb.2008.10.039 ↗
35. Si RJ, Xie XJ, Li TY, Zheng J, Cheng C, Wang CC (2020) TiO2/NaNbO3 heterojunction for boosted humidity sensing ability. Sens Actuators B Chem 309:12780310.1016/j.snb.2020.127803 ↗
36. Li TY, Si RJ, Sun J, Wang ST, Wang J, Zhu GB, Wang CC (2019) Giant and controllable humidity sensitivity achieved in (Na+Nb) co-doped rutile TiO2. Sens Actuators B Chem 29:151–15810.1016/j.snb.2019.05.019 ↗
37. Wang CC, Yang F, Wen J, Liu GZ, Lu HB (2007) Enhanced tunability due to interfacial polarization in La0.7Sr0.3MnO3/BaTiO3 multilayers. Appl Phys Lett 90:19290410.1063/1.2737368 ↗
38. Tse MY, Wei XH, Hao JH (2016) High-performance colossal permittivity materials of (Nb+Er) co-doped TiO2 for large capacitors and high-energy-density storage devices. Phys Chem Chem Phys 18:24270–2427710.1039/C6CP02236G ↗
39. Ni W, Ye JL, Guo YM, Cheng C, Lin ZQ, Li YD, Wang H, Yu Y, Li QJ, Huang SG (2017) Decisive role of mixed-valence structure in colossal dielectric constant of LaFeO3. J Am Ceram Soc 100:3042–304910.1111/jace.14860 ↗
40. Li ZW, Luo X, Wu WJ, Wu JG (2017) Niobium and divalent-modified titanium dioxide ceramics: colossal permittivity and composition design. J Am Ceram Soc 100:3004–301210.1111/jace.14850 ↗
41. Park JY, Lee YJ, Jun KW, Beag JO, Yim DJ (2006) Chemical synthesis and characterization of highly oil dispersed MgO nanoparticles. J Ind Eng Chem 12:882–887
42. Gupta P, Ganguli T, Švec P, Sinha AK, Gupta A, Švec SP, Singh MN, Reddy VR, Deb SK (2013) Effect of Co addition on the atomic ordering of FeCo-phase in nanocrystalline Fe81-xCoxNb7B12 alloys (x = 20.25, 27, 40.5, 54, 60.75): an anomalous diffraction and Mössbauer study. J Appl Phys 114:08351610.1063/1.4819398 ↗
43. Nakaruk A, Ragazzon D, Sorrell CC (2010) Anatase-rutile transformation through high-temperature annealing of titania films produced by ultrasonic spray pyrolysis. Thin Solid Films 518:3735–374210.1016/j.tsf.2009.10.109 ↗
44. Bushroa AR, Rahbari RG, Muhamad MR (2012) Approximation of crystallite size and microstrain via XRD line broadening analysis in TiSiN thin films. Vacuum 86:1107–111210.1016/j.vacuum.2011.10.011 ↗
45. Augustin A, Udupa KP, Udaya BK (2016) Crystallite size measurement and micro-strain analysis of electrodeposited copper thin film using Williamson-Hall method. AIP Conf Proc 1728:02049210.1063/1.4946543 ↗