journal article·2007-03-07

Melt rheology and extrudate morphology studies of polystyrene/polybutadiene blends in the presence and absence of compatibilisers

Susan Joseph, A. R. R. Menon, Aju Joseph, Sabu Thomas

Journal of Materials Science· Volume 42· Issue 6
Publisher page

Abstract

Melt rheology and extrudate morphology of polystyrene (PS)/polybutadiene (PB) blends were studied with special reference to the effect of blend ratio and two different types of compatibilisers, the random copolymers and block copolymers. Uncompatibilized blends had viscosities approximately intermediate between those of the component polymers. In the case of uncompatibilized blends both positive and negative deviation was observed in the viscosity-composition curve at different shear rate range studied. The viscosity of the compatibilized blend was found to increase when a few percent of block copolymer was added. However, at high concentrations of the compatibiliser, the viscosity values leveled off. This is due to interfacial saturation. Morphological investigations indicated that the size of the dispersed phase initially decreased when a few percent of the block copolymer was added followed by a clear leveling off at higher concentration. However, the random copolymer was not an effective interface modifier in agreement with microscopy study. These experimental results supports the earlier investigations of solid state NMR studies on these blends (Polymer (2005) 46(22):9385).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Polymer crystallization and properties · Rheology and Fluid Dynamics Studies · Polymer Foaming and Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Paul DR (1978) In: Paul DR, Newman S (eds) Polymer blends. Academic Press, New York10.1016/B978-0-12-546802-2.50012-9 ↗
2. Paul DR (1986) In: Paul DR, Sperling LH (eds) Multicomponent polymer materials. The American Chemical Society, Washington D.C
3. Brydson JA (1981) Flow properties of polymer melts, Ch. 1, 2nd edn. George Godwin Limited, London
4. Utracki LA (1991) J Rheol 35:161510.1122/1.550248 ↗
5. Garcia D (1986) J Polym Sci Part B: Polym Phys 24:157710.1002/polb.1986.090240714 ↗
6. Utracki LA, Kamal MR (1982) Polym Eng Sci 26:9610.1002/pen.760220211 ↗
7. Utracki LA (1974) J Polym Sci Part B: Polym Phys 12:56310.1002/pol.1974.180120310 ↗
8. Utracki LA, Sammut P (1988) Polym Eng Sci 28:140510.1002/pen.760282110 ↗
9. Han CD (1981) Multiphase flow in polymer processing. Academic Press Inc., New York
10. Akthar S, Kuriakose B, De PP, De SK (1987) Plast Rubber Process Appl 7:11
11. Danesi S, Porter RS (1978) Polymer 19:44810.1016/0032-3861(78)90255-0 ↗
12. Vanoene H (1972) Colloid J Interface Sci 40:44810.1016/0021-9797(72)90355-4 ↗
13. Koshy AT, Kuriakose B, Thomas S, Premaletha CK, Varghese KT (1993) J Appl Polym Sci 49:90110.1002/app.1993.070490516 ↗
14. Oommen Z, Thomas S, Premaletha CK, Kuriakose B (1997) Polymer 38:561110.1016/S0032-3861(97)00120-1 ↗
15. Asaletha R, Groeninckx G, Kumaran MG, Thomas S (1998) J Appl Polym Sci 69:267310.1002/(SICI)1097-4628(19980926)69:13<2673::AID-APP18>3.0.CO;2-V ↗
16. Varghese H, Bhagawan SS, Thomas S, (1999) Polym-Plast Technol Eng 38:31910.1080/03602559909351581 ↗
17. George J, Ramamurthy K, Varughese KT, Thomas S (2000) J Polym Sci Part B: Polym Phys 38:110410.1002/(SICI)1099-0488(20000501)38:9<1104::AID-POLB2>3.0.CO;2-A ↗
18. Nair SV, Oommen Z, Thomas S (2002) J Appl Polym Sci 86:353710.1002/app.11159 ↗
19. Oommen Z, Zachariah SR, Thomas S, Groeninckx G, Moldenaers P, Mewis J (2004) J Appl Polym Sci 92(1):25210.1002/app.13652 ↗
20. Germain Y, Ernst B, Genelot O, Dhamani K (1994) J Rheol 3:68110.1122/1.550602 ↗
21. Joshi M, Maiti SN, Misra A (1992) J Appl Polym Sci 45:183710.1002/app.1992.070451018 ↗
22. Haddout A, Villoutreix G (2000) Int Polym Process 15:29110.3139/217.1599 ↗
23. Van Puyvelde P, Velankar S, Moldenaers P, (2001) Curr Opin Colloid Interface Sci 6:45710.1016/S1359-0294(01)00113-3 ↗
24. Jafari SH, Potschke P, Stephan M, Warth H, Alberts H (2002) Polymer 43:698510.1016/S0032-3861(02)00614-6 ↗
25. Brahimi B, Ait-Kadi A, Aiji A, Jeone R, Fayat R (1991) J Rheol 35:106910.1122/1.550166 ↗
26. Yu W, Bousmina M, Grmela M, Palierne JF, Zhou CX (2002) J Rheol 46:138110.1122/1.1517302 ↗
27. Chu LH, Guo SH, Chiu WY, Tseng HC (1993) J Appl Polym Sci 49:179110.1002/app.1993.070491010 ↗
28. Spiegelberg SH, Argon AS, Cohen RE (1994) J Appl Polym Sci 53:125110.1002/app.1994.070530912 ↗
29. Ju MY, Chen MY, Chang FC (2000) Macromol Chem and Phys 20:2298
30. Liao GX, Jian XA, Wang JY (2002) J Mat Sci Technol 18:561
31. Lim KY, Kim BC, Yoon KJ (2002) J Polym Sci Part B: Polym Phy 40:255210.1002/polb.10302 ↗
32. Sung YT, Han MS, Hyun JC, Kim WN, Lee HS (2003) Polymer 44:168110.1016/S0032-3861(02)00920-5 ↗
33. Colbeaux A, Fenouillot F, Gerard JF, Taha M, Wautier H (2005) J Appl Polym Sci 95:31210.1002/app.21226 ↗
34. Filipe S, Cidade MT, Wilhelm M, Maia JM (2006) J Appl Polym Sci 99(1): 34710.1002/app.22393 ↗
35. Gorton DT, Pendle TD (1981) NR Technol 12:1
36. Jannasch P, Wesslen B (1995) J Appl Polym Sci 58:75310.1002/app.1995.070580408 ↗
37. Giuliani GP, Sorta E, Bruzzone M (1972) Chim Ind 54:35
38. Ciesielska D, Liu P (2000) Kautschuk Gummi Kunststoffe 53:273
39. Hashin Z (1964) In: Reiner M, Abir S (eds) Second order effects in elasticity, plasticity and fluid dynamics. Mac Milan, New York
40. Sood R, Kulkarni MG, Dutta A, Mashelkar RA (1988) Polym Eng Sci 28:2010.1002/pen.760280105 ↗
41. Joseph S, Laupretre F, Negrell C, Thomas S (2005) Polymer 46(22):938510.1016/j.polymer.2005.07.053 ↗
42. Willis JM, Favis BD (1988) Polym Eng Sci 28:141610.1002/pen.760282111 ↗
43. Varughese KT (1990) J Appl Polym Sci 39:20510.1002/app.1990.070390201 ↗
44. Wu S (1987) Polym Eng Sci 27:33510.1002/pen.760270506 ↗
45. Avgeropoulos GN, Weissert FC, Biddison PH, Bohm GGA (1976) Rub Chem Technol 49:9310.5254/1.3534954 ↗
46. Chen J, Hahn PS, Slattery JC (1984) AIChE J 30(4):62210.1002/aic.690300413 ↗