Ultrafine-grained nickel refined by dislocation activities at intermediate strain rate impact: deformation microstructure and mechanical properties
Source abstract
Abstract
This article presents an application of the impact-induced deformation in effective grain refinement in polycrystalline nickel. Ultrafine-grained microstructure was processed by means of Dynamic Plastic Deformation at room temperature using a falling impactor with a maximum impact velocity of 10 m s−1. The commercially pure (98.4 wt%) starting material was characterised by a coarse-grained (~25 μm) microstructure. Electron backscattering diffraction and transmission electron microscopy studies showed that the initial equiaxed grains evolved into a laminar structure of submicron size narrow domains delineated by high-angle grain boundaries. The texture after deformation exhibits preferential orientations including a strong 〈220〉 fibre texture. The mechanical behaviour under quasi-static compression at room temperature and at a strain rate of 2 × 10−3 s−1 was investigated in directions parallel and perpendicular to the impact axis. Stress–strain responses showed an increased yield strength (440–520 MPa) compared with the initial state (90 MPa). The strain-hardening behaviour was found to strongly depend on the orientation of the compression axis.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · High-Velocity Impact and Material Behavior · Powder Metallurgy Techniques and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Gleiter H (1989) Prog Mater Sci 33:223. doi: 10.1016/0079-6425(89)90001-710.1016/0079-6425(89)90001-7 ↗
2. Gleiter H (1992) Nanostruct Mater 1:1. doi: 10.1016/0965-9773(92)90045-Y10.1016/0965-9773(92)90045-Y ↗
3. Gleiter H (1995) Nanostruct Mater 6:3. doi: 10.1016/0965-9773(95)00025-910.1016/0965-9773(95)00025-9 ↗
4. Zener C, Hollomon JH (1944) J Appl Phys 15:22. doi: 10.1063/1.170736310.1063/1.1707363 ↗
5. Li YS et al (2009) Acta Mater 57:761. doi: 10.1016/j.actamat.2008.10.02110.1016/j.actamat.2008.10.021 ↗
6. Huang F et al (2011) J Mater Sci Technol 27(1):1. doi: 10.1016/S1005-0302(11)60017-010.1016/S1005-0302(11)60017-0 ↗
7. Ito Y, Horita Z (2009) Mater Sci Eng A 503:32. doi: 10.1016/j.msea.2008.03.05510.1016/j.msea.2008.03.055 ↗
8. Sun PL et al (2000) Mater Sci Eng A 283:82. doi: 10.1016/S0921-5093(99)00800-X10.1016/S0921-5093(99)00800-X ↗
9. Hebesberger T et al (2005) Acta Mater 53:393. doi: 10.1016/j.actamat.2004.09.04310.1016/j.actamat.2004.09.043 ↗
10. Dobatkin SV et al (2007) Mater Sci Eng A 462:132. doi: 10.1016/j.msea.2006.04.15610.1016/j.msea.2006.04.156 ↗
11. Li YS et al (2008) Acta Mater 56:230. doi: 10.1016/j.actamat.2007.09.02010.1016/j.actamat.2007.09.020 ↗
12. Zhao WS et al (2005) Scr Mater 53:745. doi: 10.1016/j.scriptamat.2005.05.02210.1016/j.scriptamat.2005.05.022 ↗
13. Abdul-Latif A et al (2009) Int J Mech Sci 51:797. doi: 10.1016/j.ijmecsci.2009.09.00510.1016/j.ijmecsci.2009.09.005 ↗
14. Ribárik G, Gubicza J, Ungár T (2004) Mater Sci Eng A 387–389:343. doi: 10.1016/j.msea.2004.01.08910.1016/j.msea.2004.01.089 ↗
15. Balogh L, Ribárik G, Ungár T (2006) J Appl Phys 100:023512. doi: 10.1063/1.221619510.1063/1.2216195 ↗
16. Hughes DA, Hansen N (1997) Acta Mater 45(9):3871. doi: 10.1016/S1359-6454(97)00027-X10.1016/S1359-6454(97)00027-X ↗
17. Hughes DA, Hansen N (2000) Acta Mater 48:2985. doi: 10.1016/S1359-6454(00)00082-310.1016/S1359-6454(00)00082-3 ↗
18. Hughes DA (2002) Scr Mater 47:697. doi: 10.1016/S1359-6462(02)00186-010.1016/S1359-6462(02)00186-0 ↗
19. Dirras G et al (2010) Phys Status Solidi A 207(10):2233. doi: 10.1002/pssa.20102609310.1002/pssa.201026093 ↗
20. Zhilyaev AP, Gubicza J, Nurislamova G et al (2003) Phys Status Solidi A 198:263. doi: 10.1002/pssa.20030660810.1002/pssa.200306608 ↗
21. Setman DE et al (2008) Mater Sci Eng A 493:116. doi: 10.1016/j.msea.2007.06.09310.1016/j.msea.2007.06.093 ↗
22. Krasilnikov N, Lojkowski W, Pakiela Z, Valiev R (2005) Mater Sci Eng A 397:330. doi: 10.1016/j.msea.2005.03.00110.1016/j.msea.2005.03.001 ↗
23. Keller C, Hug E (2008) Mater Lett 62:1718. doi: 10.1016/j.matlet.2007.09.06910.1016/j.matlet.2007.09.069 ↗
24. Thompson AW (1977) In: Thompson AW (ed) Work hardening in tension and fatigue. TMS-AIME, New York
25. Gubicza J et al (2009) J Alloys Compd 483:271. doi: 10.1016/j.jallcom.2008.07.20010.1016/j.jallcom.2008.07.200 ↗