journal article·2014-01

Kinetic model study of moisture sorption–desorption–resorption in triangular-shaped vinyl ester filler/epoxy composites

Bryan B. Pajarito, Masatoshi Kubouchi

Journal of Materials Science· Volume 49· Issue 2
Publisher page

Abstract

A phenomenological diffusion model was used to study and describe moisture sorption–desorption–resorption kinetics in triangular-shaped vinyl ester filler/epoxy composites at 80 °C. The model was derived to predict the experimental anomalous weight gain behaviors of epoxy composites during moisture sorption and resorption, and estimate the degree of material degradation and loss observed as negative weight change during desorption. To verify the applicability of the model, acid anhydride–cured epoxy composites were prepared at varied alignment (parallel or staggered), spacing (1 or 5 mm), and orientation (pointed or flat) of triangular-shaped vinyl ester fillers. Moisture sorption–desorption–resorption experiment was performed by immersion of specimens in deionized water for 1200 h, followed by vacuum drying for 300 h, and water reimmersion for 300 h. The parameters of the model were calculated from nonlinear regression of percent weight change versus time experimental data. The model was found to be in good agreement with the weight change kinetic curves of all specimens. Results of three-way analysis of variance of model parameters showed the degree of material degradation and moisture diffusion coefficients during sorption, desorption, and resorption to be significantly affected by triangular-shaped filler alignment, spacing, and orientation. Using staggered over parallel alignment and 5-mm over 1-mm spacing decreased material degradation and moisture transport rate during desorption in composites. Increasing the spacing from 1 to 5 mm decreased moisture diffusion during sorption. Orienting the fillers from pointed to flat decreased moisture diffusion during resorption. Effect of interaction of filler spacing and orientation was also found to be statistically significant on the diffusion rate during sorption.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Epoxy Resin Curing Processes · Polymer Nanocomposites and Properties · Mechanical Behavior of Composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. Moggridge GD, Lape NK, Yang C, Cussler EL (2003) Prog Org Coat 46:23110.1016/S0300-9440(02)00180-7 ↗
2. Lape NK, Nuxoll EE, Cussler EL (2004) J Membr Sci 236:2910.1016/j.memsci.2003.12.026 ↗
3. Chen X, Papathanasiou TD (2007) J Plast Film Sheet 23:31910.1177/8756087907088437 ↗
4. Cussler EL (2007) Diffus Fund 6:72
5. Yang C, Smyrl W, Cussler EL (2004) J Membr Sci 231:110.1016/j.memsci.2003.09.022 ↗
6. Falla W, Mulski M, Cussler EL (1996) J Membr Sci 119:12910.1016/0376-7388(96)00106-8 ↗
7. DeRocher J, Gettelfinger B, Wang J, Nuxoll E, Cussler EL (2005) J Membr Sci 254:2110.1016/j.memsci.2004.12.025 ↗
8. Cussler EL, Hughes S, Ward W, Aris R (1988) J Membr Sci 38:16110.1016/S0376-7388(00)80877-7 ↗
9. Fredrickson G, Bicerano J (1999) J Chem Phys 110:218110.1063/1.477829 ↗
10. Brydges W, Gulati S, Baum G (1975) J Mater Sci 10:2044. doi: 10.1007/BF0055748210.1007/BF00557482 ↗
11. Swannack C, Cox C, Liakos A, Hirt D (2005) J Membr Sci 263:4710.1016/j.memsci.2005.04.023 ↗
12. Eitzmann D, Melkote R, Cussler EL (1996) AIChE J 42:210.1002/aic.690420103 ↗
13. Ly Y, Cheng Y (1997) J Membr Sci 133:20710.1016/S0376-7388(97)00085-9 ↗
14. White J, Cussler EL (2006) J Membr Sci 278:22510.1016/j.memsci.2005.10.059 ↗
15. Pajarito BB, Kubouchi M, Tomita H, Sakai T (2012) Mater Sci Technol Jpn 49:32
16. Pajarito BB, Kubouchi M, Sakai T, Aoki S (2012) J Soc Mater Sci Jpn 10:86010.2472/jsms.61.860 ↗
17. Pajarito BB, Kubouchi M, Aoki S (2012) Adv Compos Lett 21:13710.1177/096369351202100601 ↗
18. Lin YC, Chen X (2005) Polymer 46:1199410.1016/j.polymer.2005.10.002 ↗
19. Fan XJ, Lee SWR, Han Q (2009) Microelectron Reliab 49:86110.1016/j.microrel.2009.03.006 ↗
20. Yur’ev SV, Lushchik VV (1975) Mater Sci 10:5010.1007/BF00715486 ↗
21. Crank J (1975) The mathematics of diffusion. Clarendon, Oxford
22. Pomerantsev AL (2005) J Appl Polym Sci 96:110210.1002/app.21540 ↗
23. Long FA, Richman D (1960) J Am Chem Soc 82:51310.1021/ja01488a002 ↗
24. Berens AR, Hopfenberg HB (1978) Polymer 19:48910.1016/0032-3861(78)90269-0 ↗
25. De Wilde WP, Shopov PJ (1994) Compos Struct 27:24310.1016/0263-8223(94)90085-X ↗
26. Weitsman YJ, Guo YJ (2002) Compos Sci Technol 62:88910.1016/S0266-3538(02)00032-5 ↗
27. Weitsman YJ (2006) Compos Part A 37:61710.1016/j.compositesa.2005.05.022 ↗
28. Weitsman YJ (2012) Fluid effects in polymers and polymeric composites. Springer, New York10.1007/978-1-4614-1059-1 ↗
29. Mubashar A, Ashcroft IA, Critchlow GW, Crocombe AD (2009) J Adhesion 85:71110.1080/00218460902997224 ↗
30. Lee S, Rockett TJ (1992) Polymer 33:369110.1016/0032-3861(92)90657-I ↗
31. Alvarez V, Vazquez A, de la Osa O (2007) J Compos Mater 41:127510.1177/0021998306067311 ↗
32. Lazic ZR (2004) Design of experiments in chemical engineering. WILEY-VCH Verlag GmbH & Co, KGaA10.1002/3527604162 ↗
33. Sorrentino A, Tortora M, Vittoria V (2006) J Polym Sci Pol Phys 44:26510.1002/polb.20684 ↗
34. Choudalakis G, Gotsis AD (2009) Eur Polym J 45:96710.1016/j.eurpolymj.2009.01.027 ↗