journal article·2014-04

Crystallization and microstructure of metastable water quenched nanostructured 8 mol% yttria-stabilized zirconia using the solution precursor plasma spray method

Mirela A. Dragan, Peter Strutt, Radenka Maric

Journal of Materials Science· Volume 49· Issue 8
Publisher page

Abstract

A t′ tetragonally structured metastable 8 mol% yttria-stabilized zirconia (8 mol% YSZ) nanomaterial was synthesized by means of solution thermal plasma spray with water quenching of reacted species. Synthesis of the 8 mol% YSZ powder involved vaporization of a liquid precursor injected into a plasma jet where individual droplets, depending on their trajectory within the plasma, experienced varied thermal histories. Thus, not all the material produced underwent a complete gel → glass → nanocrystalline transformation sequence. Consequently, the collected powder contained a proportion of gel and glass (amorphous) state material. Additionally, the powder contained nano-scale and small micron-scale rapidly solidified 8 mol% YSZ particles. Following thermal treatment, the gel and the amorphous content transformed to produce (i) densely packed nanograin and (ii) chain-like nanograin aggregates. The nanograin aggregates are suggestive of a strong, yet short-range intergranular attraction, as predicted in computer simulation studies presented in the literature. Interestingly, this mixed morphology powder, after compaction and heat treatment at 1400 °C for 2 h, transformed into 98 % dense material with a homogeneous 200–500 nm grain size. For generating 8 mol% YSZ, the solution precursor plasma spray method offers a high synthesis rate using a low-cost precursor to produce powder that can be consolidated into morphologically homogeneous bulk nanomaterial.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Catalytic Processes in Materials Science · Electronic and Structural Properties of Oxides

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (63)

Show source-provided references
1. Schlichting KW, Padture NP, Klemens PG (2001) Thermal conductivity of dense and porous yttria-stabilized zirconia. J Mater Sci 36:3003–3010. doi: 10.1023/A:101797092431210.1023/A:1017970924312 ↗
2. Lima RS, Kucuk A, Berndt CC (2001) Integrity of nanostructured partially stabilized zirconia after plasma spray processing. Mater Sci Eng A 313:75–8210.1016/S0921-5093(01)01146-7 ↗
3. Lima RS, Marple BR (2007) Thermal spray coatings engineered from nanostructured ceramic agglomerated powders for structural, thermal barrier and biomedical applications: a review. J Therm Spray Technol 16:41–64
4. Minh NQ, Takahashi T (1995) Science and technology of ceramic fuel cells. Elsevier, Amsterdam
5. Huang J, Xie F, Wang C, Mao Z (2012) Development of solid oxide fuel cell materials for intermediate-to-low temperature operation. Int J Hydrogen Energy 37:877–88310.1016/j.ijhydene.2011.04.030 ↗
6. He B, Zhao L, Song S, Jiang Z, Xia C (2011) Ni–Sm2O3 cermet anodes for intermediate-temperature solid oxide fuel cells with stabilized zirconia electrolytes. Int J Hydrogen Energy 36:5589–559410.1016/j.ijhydene.2011.01.148 ↗
7. Gruner HT, Tannenberger H (1994) SOFC elements by vacuum-plasma-spraying (VPS). In: Proceedings of 1st European solid oxide fuel cell conference, Lucerne, Switzerland, vol 2, pp 611–616
8. Wang Z, Ghosh D, Hui R, Bogdanovic N, Tang Z, Yick S, Xie Y, Maric R, Ghosh D (2007) Plasma spray synthesis of ultra-fine YSZ powder. J Power Sources 170:145–14910.1016/j.jpowsour.2007.04.024 ↗
9. Martin PJ, Netterfield RP, Saity WG (1984) Modification of the optical and structure properties of dielectric ZrO2 films by ion-assisted deposition. J Appl Phys 67:4872–4880
10. Stamper K, Greve DW, Schlesinger TE (1991) Deposition of textured yittria-stabilized ZrO2 film on oxidized silicon. J Appl Phys 70:2046–205110.1063/1.349464 ↗
11. Wachsman ED, Lee KT (2011) Lowering the temperature of solid oxide fuel cells. Science 334:935–93910.1126/science.1204090 ↗
12. Maric R, Roller J, Neagu R (2011) Flame-based technologies and reactive spray deposition technology for low temperature solid oxide fuel cells: technical and economic aspects. J Therm Spray Technol 20:696–71810.1007/s11666-011-9645-x ↗
13. Duwez P, Brown HF, Odell F (1951) The zirconia–yttria system. J Electrochem Soc 98:356–36210.1149/1.2778219 ↗
14. Scott HG (1975) Phase relationships in the zirconia–yttria system. J Mater Sci 10:1527–1535. doi: 10.1007/BF0103185310.1007/BF01031853 ↗
15. Stubican VS, Hink RC, Ray SP (1978) Phase equilibria and ordering in the system ZrO2–Y2O3. J Am Ceram Soc 61:17–2110.1111/j.1151-2916.1978.tb09220.x ↗
16. Suzuki Y (1995) Phase transition temperature of fluorite-type ZrO2–Y2O3 solid solutions containing 8–44 mol% Y2O3. Solid State Ion 81:211–21610.1016/0167-2738(95)00186-A ↗
17. Yashima M, Kakihana M, Yoshimura M (1996) Metastable-stable phase diagrams in the zirconia-containing systems utilized in solid-oxide fuel cell application. Solid State Ion 86–88:1131–114910.1016/0167-2738(96)00386-4 ↗
18. Chevalier J, Gremillard L, Virkar AV, Clarke DR (2009) The tetragonal–monoclinic transition in zirconia: lessons learned and future trends. J Am Ceram Soc 92:1901–192010.1111/j.1551-2916.2009.03278.x ↗
19. Fabrichnaya O, Wang C, Zinkevich M, Levi CG, Aldinger F (2005) Phase equilibria and thermodynamic properties of the ZrO2–GdO1.5–YO1.5 system. J Phase Equilib Diffus 26:591–60410.1007/s11669-005-0004-9 ↗
20. Mercer C, Williams JR, Clarke DR, Evans AG (2007) On a ferroelastic mechanism governing the toughness of metastable tetragonal-prime (t’) yttria-stabilized zirconia. Proc R Soc A 463:1393–140810.1098/rspa.2007.1829 ↗
21. Strutt PR, Kear BH, Boland RF (2000) U.S. Patent 6,447,848
22. Padture NP, Schlichting KW, Bhatia T, Ozturk A, Cetegen B, Jordan EH, Gell M, Jiang S, Xiao TD, Strutt PR, Garcí E, Miranzo P, Osendi MI (2001) Towards durable thermal barrier coatings with novel microstructures deposited by solution-precursor plasma spray. Acta Mater 49:2251–225710.1016/S1359-6454(01)00130-6 ↗
23. Gell M, Jordan EH, Teicholz M, Cetegen BM, Padture NP, Xie L, Chen D, Ma X, Roth J (2007) Thermal barrier coatings made by the solution precursor plasma spray process. J Therm Spray Technol 17:124–13510.1007/s11666-007-9141-5 ↗
24. Xie L, Ma X, Jordan EH, Padture NP, Xiao DT, Gell M (2003) Identification of coating deposition mechanisms in the solution precursor plasma spray process using model spray experiments. Mater Sci Eng A 362:204–21210.1016/S0921-5093(03)00617-8 ↗
25. Ozturk A, Cetegen M (2004) Modeling of plasma assisted formation of precipitates in zirconium containing liquid precursor droplets. Mater Sci Eng A 384:331–35110.1016/S0921-5093(04)00870-6 ↗
26. Xie L, Jordan EH, Gell M (2004) Phase and microstructural stability of precursor plasma sprayed thermal barrier coatings. Mater Sci Eng A 381:189–19510.1016/j.msea.2004.04.042 ↗
27. Xie L, Ma X, Jordan EH et al (2004) Deposition of thermal barrier coatings using solution precursor plasma spray process. J Mater Sci 39:1636–1639. doi: 10.1023/B:JMSC.0000016163.81534.19
28. Basu S, Cetegen BM (2007) Modeling of thermophysical processes in liquid ceramic precursor droplets injected into a plasma jet. Int J Heat Mass Trans 50:3278–329010.1016/j.ijheatmasstransfer.2007.01.036 ↗
29. Tarasi F, Medraj M, Dolatabadi A et al (2013) Enhancement of amorphous phase formation in alumina: YSZ coatings deposited by suspension plasma spray process. Surf Coat Technol 220:191–19810.1016/j.surfcoat.2012.10.054 ↗
30. Govindarajan S, Dusane RO, Joshi SV (2011) In situ particle generation and splat formation during solution precursor plasma spraying of yttria-stabilized zirconia coatings. J Am Ceram Soc 94:4191–419910.1111/j.1551-2916.2011.04773.x ↗
31. Hui R, Wang Z, Kesler O et al (2007) Thermal plasma spraying for SOFCs: applications, potential advantages, and challenges. J Power Sources 170:308–32310.1016/j.jpowsour.2007.03.075 ↗
32. Stover D, Hathiramani D, Vaben R, Damai RJ (2006) Plasma-sprayed components for SOFC applications. Surf Coat Technol 201:2002–200510.1016/j.surfcoat.2006.04.039 ↗
33. Viazzi C, Bonino J, Ansart F, Barnabe A (2008) Structural study of metastable tetragonal YSZ powders produced via a sol–gel route. J Alloys Compd 452:377–38310.1016/j.jallcom.2006.10.155 ↗
34. Will J, Mitterdorfer A, Kleinlogel C et al (2000) Fabrication of thin electrolytes for second generation solid oxide fuel cells. Solid State Ion 131:79–9610.1016/S0167-2738(00)00624-X ↗
35. Papet P, Lebars N, Baumard J et al (1989) Transparent monolithic zirconia gels: effects of acetylacetone content on gelation. J Mater Sci 24:3850–3854. doi: 10.1007/BF0116894610.1007/BF01168946 ↗
36. Zhou X, Shukla V, Cannon W, Kear B (2003) Metastable phase formation in plasma-sprayed ZrO2 (Y2O3)–Al2O3. J Am Ceram Soc 86:1415–142010.1111/j.1151-2916.2003.tb03485.x ↗
37. Scherrer B, Heiroth S, Hafner R et al (2011) Crystallization and microstructure of yttria-stabilized-zirconia thin films deposited by spray pyrolysis. Adv Funct Mater 21:3967–397510.1002/adfm.201101268 ↗
38. Perednis D, Wilhelm O, Pratsinis S, Gauckler L (2005) Morphology and deposition of thin yttria-stabilized zirconia films using spray pyrolysis. Thin Solid Films 474:84–9510.1016/j.tsf.2004.08.014 ↗
39. Berghaus OJ, Legoux JG, Moreau C et al (2008) Suspension HVOF spraying of reduced temperature solid oxide fuel cell electrolytes. J Therm Spray Technol 17:700–70710.1007/s11666-008-9249-2 ↗
40. Maric R, Furusaki K, Nishijima D, Neagu R (2011) Thin film low temperature solid oxide: fuel cell (LTSOFC) by reactive spray deposition technology. ECS Trans 35:473–48110.1149/1.3570023 ↗
41. Maric R, Fukui T, Ohara S et al (2000) Powder prepared by spray pyrolysis as an electrode material for solid oxide fuel cells. J Mater Sci 35:1397–1404. doi: 10.1023/A:100475472923110.1023/A:1004754729231 ↗
42. Miller RA, Smialek JL, Garlick RG (1981) Science and technology of zirconia. In: Hewer AH, Hob LW (eds) Advances in ceramics. American Ceramic Society, Columbus, pp 241–253
43. Yashima M, Sasaki S, Kakihama M et al (1994) Oxygen-induced structural change of the tetragonal phase around the tetragonal–cubic phase-boundary in ZrO2–YO1.5 solid-solutions. Acta Crystallogr Sect B 50:663–67210.1107/S0108768194006257 ↗
44. Krogstad JA, Lepple M, Gao Y et al (2011) Effect of yttria content on the zirconia unit cell parameter. J Am Ceram Soc 94:4548–455510.1111/j.1551-2916.2011.04862.x ↗
45. Virkar A, Matsumoto R (1986) Ferroelastic domain switching as a toughening mechanism in tetragonal zirconia. J Am Ceram Soc 69:C224–C22610.1111/j.1151-2916.1986.tb07341.x ↗
46. Salje EKH (2013) Ferroelastic materials. Ann Rev Mater Res 42:265–28310.1146/annurev-matsci-070511-155022 ↗
47. Baither D, Baufeld B, Messerschmidt U et al (1997) Ferroelasticity of t’-zirconia 1. High-voltage electron microscopy studies of the microstructure in polydomain tetragonal zirconia. J Am Ceram Soc 80:1691–169810.1111/j.1151-2916.1997.tb03040.x ↗
48. Baufeld B, Baither D, Messerschmidt U et al (1997) Ferroelasticity of t’-zirconia: in-situ straining in a high-voltage electron microscope. J Am Ceram Soc 80:1699–170310.1111/j.1151-2916.1997.tb03041.x ↗
49. Maher RC (2012) Raman spectroscopy for solid oxide fuel cells. In: Yarwood J, Douthwaite R, Duckett S (eds) Spectroscopic properties of inorganic and organometallic compounds: techniques, materials and applications. The Royal Society of Chemistry, UK, pp 84–12210.1039/9781849734899-00084 ↗
50. Kisi EH, Howard CJ (1998) Crystal structures of zirconium phases and their inter-relation. Key Eng Mater 153–154:1–3610.4028/www.scientific.net/KEM.153-154.1 ↗
51. Yashima M, Ohtake K, Arashi H, Kakihana M, Yoshimura M (1993) Determination of cubic–tetragonal phase boundary in Zr1−X Y X O2−X/2 solid solutions by Raman spectroscopy. J Appl Phys 74:760310.1063/1.354989 ↗
52. Fadda G, Zanzotto G, Colombo L (2010) First-principles study of the effect of pressure on the five zirconia polymorphs. II. Static dielectric properties and Raman spectra. Phys Rev B 82:06410610.1103/PhysRevB.82.064106 ↗
53. Heiroth S, Lippert T, Wokaun A, Döbeli M, Rupp JLM, Scherrer B, Gauckler LJ (2010) Yttria-stabilized zirconia thin films by pulsed laser deposition: microstructural and compositional control. J Eur Ceram Soc 30:489–49510.1016/j.jeurceramsoc.2009.06.012 ↗
54. Howard CJ, Hunter BA, Kim D (1998) Oxygen position and bond lengths from lattice parameters in tetragonal zirconias. J Am Ceram Soc 81:241–24310.1111/j.1151-2916.1998.tb02324.x ↗
55. Lu P, Weitz D (2013) Colloidal particles: crystals, glasses, and gels. Annu Rev Cond Mat Phys 4:217–23310.1146/annurev-conmatphys-030212-184213 ↗
56. Wolde PR, Frenkel D (1999) Homogeneous nucleation and the Ostwald step. Phys Chem Chem Phys 1:2191–219610.1039/a809346f ↗
57. Gruner H, Tannenberger H (1994) US Patent 5,328,779 A, 12 July 199410.1038/nbt0494-328a ↗
58. Henne R (2007) Solid oxide fuel cells: a challenge for plasma deposition processes. J Thermo Spray Technol 16:381–40310.1007/s11666-007-9053-4 ↗
59. Rupp JLM, Scherrer B, Gauckler LJ (2010) Engineering disorder in precipitation-based nano-scaled metal oxide thin films. Phys Chem Chem Phys 12:11114–1112410.1039/b920971a ↗
60. van der Sluis P, Hezemans A, Kroon J (1991) Computer knowledge base for crystallization. J Cryst Growth 108:719–72710.1016/0022-0248(91)90252-Z ↗
61. Gorbitz CH, Hersleth HP (2000) On the inclusion of solvent molecules in the crystal structures of organic compounds. Acta Crystallogr Sect B 56:526–53410.1107/S0108768100000501 ↗
62. Kang HS, Kang YC, Koo HY et al (2006) Nano-sized ceria particles prepared by spray pyrolysis using polymeric precursor solution. Mater Sci Eng B 127:99–10410.1016/j.mseb.2005.09.063 ↗
63. Ksapabutr B, Gulari E, Wongkasemjit S (2006) Sol–gel derived porous ceria powders using cerium glycolate complex as precursor. Mater Chem Phys 99:318–32410.1016/j.matchemphys.2005.10.030 ↗