Indentation analysis of plasma-sprayed Cr3C2-NiCr coatings
Source abstract
Abstract
Thermal spray coatings are widely applied as antiwear solutions in a variety of industries. In such applications, the coatings are frequently susceptible to two competing mechanical responses, (a) indentation deformation and (b) fracture, caused by erodent, abrasive, and debris originated from the environment or produced during use [1–4]. Microhardness and fracture toughness can quantify the resistance to deformation and fracture, respectively [5]. Thus indentation tests, especially Vickers indentation tests for determining the microhardness and fracture toughness of materials, are commonly used as quality control tools. Correspondingly, the Vickers hardness of thermal spray coatings considering measurement locations, directions, and indenter loads were studied [6–8]. The fracture toughness values of some coatings were measured employing the Vickers indentation technique and correlated with the friction and wear behaviors of the coatings [4, 9, 10]. However, no attempt was made so far to combine the Vickers hardness and fracture toughness into a common description for thermal spray coatings. Thermal sprayed Cr3C2-NiCr coatings are often used in high temperature applications such as in turbine engine and steel industry [2, 4, 11, 12]. Several studies have contributed to the processing, characterization, mechanical, and tribological properties of this type of coating [2, 4, 8, 11–18]. Plastic deformation [15], interlamellar boundary sliding [8, 17, 18], and intralamellar cracking, [19] were proposed to explain the mechanical properties and wear behavior of these coatings. In the present study, a universal deformation/fracture diagram, based on the methodology developed by Lawn and Marshall [5], has been presented for plasmasprayed Cr3C2-NiCr coatings using several feedstock materials. The threshold loads and crack dimensions that the coatings might sustain in a contact event, without the onset of fracture, are obtained from the universal deformation/fracture diagram. The purpose of this paper is to assess the susceptibilities to deformation and fracture of the coatings with respect to the starting powders, coating microstructure, and indentation direction, so as to provide a physical insight into the mechanical and tribological properties of the coatings.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Advanced materials and composites · High-Temperature Coating Behaviors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. R. W. Smith and R. Novak, Powder Metall. Int. 3(1991) 147.
2. G. Barbezat, A. R. Nicoll and A. Sickinger, Wear 162–164(1993) 529.10.1016/0043-1648(93)90538-W ↗
3. B. Q. Wang and K. Luer, ibid. 174(1994) 177.10.1016/0043-1648(94)90100-7 ↗
4. G. Barbezat, A. R. Nicoll, Y. S. Yin and X. Y. Sheng, Tribol. Trans. 38(1995) 845.10.1080/10402009508983478 ↗
5. B. R. Lawn and D. B. Marshall, J. Amer. Ceram. Soc. 62(7/8) (1979) 347.10.1111/j.1151-2916.1979.tb19075.x ↗
6. C. C. Berndt, J. Karthikeyan, R. Ratnaraj and Y. D. Jun, in “Thermal Spray Coatings: Properties, Processes and Applications,” edited by T. F. Bernecki (ASM International, Materials Park, Ohio, USA, 1992) p. 199.
7. C. K. Lin, S. H. Leigh and C. C. Berndt, in “Thermal Spraying: Current Status and Future Trends,” edited by A. Ohmori (High Temperature Society of Japan, Osaka, Japan, 1995) p. 903.
8. J. F. Li and C. X. Ding, J. Chin. Ceram. Soc. 28(3) (2000) 223.
9. G. K. Beshish, C. W. Florey, F. J. Worzala and W. J. Lenling, J. Therm. Spray Techn. 2(1) (1993) 35.10.1007/BF02647421 ↗
10. J. LI, Y. Zhang, J. Huang and C. Ding, ibid. 7(2) (1998) 242.10.1361/105996398770350981 ↗
11. J. Takeuchi, Y. Murata, Y. Harada, T. Tomita, S. Nakahama and T. Go, in “Thermal Spray: Meeting the Challenges of the 21th Century,” edited by C. Coddet (ASM International, Materials Park, Ohio, USA, 1998) p. 1425.
12. D. R. Sielski and P. Sahoo, in “Thermal Spray: Practical Solutions for Engineering Problems,” edited by C. C. Berndt (ASM International, Materials Park, Ohio, USA, 1996) p. 159.
13. M. Mohany, R. W. Smith, M. De Bonte, J. P. Celis and E. Lugscheider, Wear 198(1996) 151.
14. J. M. Guilemany, J. Nutting and N. Liorca-Isern, J. Therm. Spray Technol. 5(4) (1996) 483.10.1007/BF02645280 ↗
15. J. F. Li, C. X. Ding, J. Q. Huang and P. Y. Zhang, Wear 211(1997) 177.10.1016/S0043-1648(97)00109-9 ↗
16. J. F. Li and C. X. Ding, J. Mater. Sci. Lett. 18(1999) 1591.10.1023/A:1006612400007 ↗
17. Idem., Wear 240(2000) 180.10.1016/S0043-1648(00)00355-0 ↗
18. Idem., Surf. Coat. Technol. 130(2000) 15.10.1016/S0257-8972(00)00678-2 ↗
19. Idem., ibid. 135(2001) 229.10.1006/bojl.2000.0409 ↗
20. J. F. Li and C. X. Ding, Thin Solid Films 376(2000) 179.10.1016/S0040-6090(00)01202-5 ↗
21. S. H. Leigh, C. K. Lin and C. C. Berndt, J. Amer. Ceram. Soc. 80(8) (1997) 2093.10.1111/j.1151-2916.1997.tb03093.x ↗
22. B. R. Lawn and A. G. Evans, J. Mater. Sci. 12(11) (1977) 2195.10.1007/BF00552240 ↗
23. B. R. Lawn, A. G. Evans and D. B. Marshall, ibid. 63(9/10) (1980) 574.