Influence of processing factors on the sheared-edge formability of vanadium bearing dual-phase steels produced using continuous galvanizing line simulations
Source abstract
Abstract
Dual-phase steels are commercially attractive since they offer good formability at a high strength and reasonable cost. In addition to high strength, these steels also exhibit high “n-values” and high uniform and total tensile elongations. However, one limitation in the application of high-strength dual-phase steels is the fairly limited ductility observed during sheared-edge stretching or punched hole expansion. Therefore, successful high-strength dual-phase steels must have controlled microstructures in order to achieve the desired performance. The failure mechanism observed during stretching of the sheared edge is closely related to the microstructures (i.e., amount, hardness, size and distribution of the different phases and microconstituents), and the cracks were found to initiate predominately at the interphase interfaces separating the ferrite and the martensite. In the present research, the influence of three main variables on the hole expansion ratio (HER) behavior was explored: the metallurgical condition going into the continuous galvanizing line (CGL), different post-anneal CG line thermal processing paths and the influence of vanadium. Depending on conditions, all three variables can influence the sheared-edge ductility as determined in the hole expansion test. Suggestions for improving the sheared-edge ductility while maintaining adequate strength are presented.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (24)
Show source-provided references
1. Kot RA, Morris JW (1979) Structure and properties of dual-phase steels. TMS-AIME, Warrendale, PA
2. Kot RA, Bramfit BL (1981) Fundamentals of dual-phase steels. TMS-AIME, Warrendale, PA
3. Fang X, Fan Z, Ralph B, Evans P, Underhill R (2003) The relationships between tensile properties and hole expansion property of C–Mn steels. J Mater Sci 38:3877–3882. https://doi.org/10.1023/A:102591312383210.1023/A:1025913123832 ↗
4. Hashimoto S (2007) Effect of niobium on Zn-coated dual phase steel sheet. Mater Sci Forum 539–543:4411–441610.4028/www.scientific.net/MSF.539-543.4411 ↗
5. Lee J, Lee S, De Cooman BC (2012) Effect of micro-alloying elements on the stretch-flangeability of dual phase steel. Mater Sci Eng A 536:231–23810.1016/j.msea.2012.01.003 ↗
6. Sudo M, Hashimoto S, Kambe S (1983) Niobium bearing ferrite-bainite high strength hot-rolled sheet steel with improved formability. Trans Iron Steel Inst Jpn 23:303–31110.2355/isijinternational1966.23.303 ↗
7. Fang X, Fan Z, Ralph B, Evans P, Underhill R (2003) Effects of tempering temperature on tensile and hole expansion properties of a C–Mn steel. J Mater Process Technol 132:215–21810.1016/S0924-0136(02)00923-8 ↗
8. Hasegawa K, Kawamura K, Urabe T, Hosoya Y (2004) Effects of microstructure on stretch-flange-formability of 980 MPa grade cold-rolled ultra-high strength steel sheets. ISIJ Int 44:603–60910.2355/isijinternational.44.603 ↗
9. Kamp A, Celotto S, Hanlon DN (2012) Effects of tempering on the mechanical properties of high strength dual-phase steels. Mater Sci Eng A 538:35–4110.1016/j.msea.2012.01.008 ↗
10. Karelova A, Krempaszky C, Werner E, Tsipouridis P, Hebesberger T, Pichler A (2009) Hole expansion of dual-phase and complex-phase AHS steels - effect of edge conditions. Steel Res Int 80:71–77
11. Levy BS, Gibbs M, Van Tyne CJ (2013) Failure during sheared edge stretching of dual-phase steels. Metall Mater Trans A 44:3635–364810.1007/s11661-013-1718-7 ↗
12. Comstock RJ, Scherrer DK, Adamczyk RD (2006) Hole expansion in a variety of sheet steels. J Mater Eng Perform 15:675–68310.1361/105994906X150830 ↗
13. Gong Y, Uusitalo J, Hua M, Wu Y, DeArdo AJ (2019) Effects of pre-annealing conditions on the microstructure and properties of vanadium-bearing dual-phase steels produced using continuous galvanizing line simulations. J Mater Sci 54:7211–7230. https://doi.org/10.1007/s10853-019-03338-610.1007/s10853-019-03338-6 ↗
14. Cho K, Garcia CI and DeArdo AJ (2010) Development of tempering resistant dual phase 980 steel during GI and GA simulated processing conditions. Unpublished research report to Vanitec, University of Pittsburgh
15. Speer J, Matlock DK, De Cooman BC, Schroth JG (2003) Carbon partitioning into austenite after martensite transformation. Acta Mater 51:2611–262210.1016/S1359-6454(03)00059-4 ↗
16. Edmonds DV et al (2006) Quenching and partitioning martensite—a novel steel heat treatment. Mater Sci Eng A 438:25–3410.1016/j.msea.2006.02.133 ↗
17. Fang C, Garcia CI, Choi S, DeArdo AJ (2015) A study of the batch annealing of cold-rolled HSLA steels containing niobium or titanium. Metall Mater Trans A 46:3635–364510.1007/s11661-015-2949-6 ↗
18. Reesman J et al (2014) Hole expansion ratio testing, MEMS 1043 senior design project, Unpublished research, University of Pittsburgh
19. Soloski PA, Thimons NJ, Marks AA et al (2015) Sheared-edge ductility/hole-expansion ratio testing of advanced high-strength steels. In: Materials Science &technology 2015, Columbus, pp 917–926
20. ISO/TS 16630:2003(E) Metallic materials-method of hole expanding test
21. Gong Y (2015) The mechanical properties and microstructures of vanadium bearing high strength dual phase steels processed with continuous galvanizing line simulations, Ph.D. Dissertation, University of Pittsburgh
22. Hua M, Gong Y, Gordillo M, Glodowski RJ, DeArdo AJ (2015) HRTEM on the precipitates in V-added DP980 steel. In: Materials science and technology 2015, Columbus, pp 947–953
23. Pathak N, Butcher C, Worswick MJ, Bellhouse E, Gao J (2017) Damage evolution in complex-phase and dual-phase steels during edge stretching. Materials 10:34610.3390/ma10040346 ↗
24. Paul SK (2014) Non-linear correlation between uniaxial tensile properties and shear-edge hole expansion ratio. J Mater Eng Perform 23:3610–361910.1007/s11665-014-1161-y ↗