Hot compression and fracture toughness of HSS composed hot strip work rolls
Source abstract
Abstract
The rolls in the finishing stands must have good resistance to both wear and fire cracks. The use of high-speed steel at the finishing stands has shown satisfactory results. The composition of this high-alloyed steel is an important parameter as the most significant change lays on the type, morphology, and volume fraction of the eutectics carbides. The heat treatment of these products consists of high temperature austenization followed by quenching and two temperings, as required in order to increase their overall hardness and to completely eliminate residual austenite. The influence of tempering temperatures on the mechanical properties of these products, determined using tensile, hot compression and fracture toughness tests, was studied in this research work. Their corresponding failure micromechanisms were defined by means of the analysis of fracture surfaces.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Alloys Wear and Properties · Advanced materials and composites · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (19)
Show source-provided references
1. Walmag G, Skoszynsky RJ, Breyer JP (2001) Improvement of the work roll performance on the 2050 mm Hot Strip Mill at Iscor Vanderbijipark, La Revue De Metallurgie-CIT, Mars 2001, pp 295–30410.1051/metal:2001184 ↗
2. Rong W, Andren H-O, Wissel H, Dunlop GL (1992) Acta Metall Mater 40:172710.1016/0956-7151(92)90116-V ↗
3. Kirn SW, Lee UJ, Woo KD, Kirn DK (2003) Mater Sci Technol 19:172710.1179/026708303225008356 ↗
4. Tabrett CP, Sare IR (2000) J Mater Sci 35:206910.1023/A:1004755511214 ↗
5. Zhang MX, Kelly PM, Gates JD (2001) J Mater Sci 36:386510.1023/A:1017949600733 ↗
6. Dogan ON, Hawk JA, Laird G (1997) Met Mat Trans 28A:131510.1007/s11661-997-0267-3 ↗
7. Bocalini M, Goldenstein H (2001) Intl Mater Rev 46(2):92–11510.1179/095066001101528411 ↗
8. Kanninen MF, Popelar CH (1985) Advanced fracture mechanics, Ch. 1. Clarendon Press, Oxford10.1520/STP34242S ↗
9. Stevens PG, Ivens KP, Harper P (1971) Iron Steel Inst 209:1
10. Ryu JH, Kwon O, Lee PJ, Kirn YM (1992) Iron Steel Inst Jpn 32:122110.2355/isijinternational.32.1221 ↗
11. De Barbadillo JJ, Trozzi CJ (1981) Iron Steel Eng 58:63
12. Judo RR (1979) Iron Steel Eng 56:51
13. Hwang KC, Lee S, Lee HC (1998) Mater Sci Eng A254 (1998) 29610.1016/S0921-5093(98)00694-7 ↗
14. Hwang LC, Lee S, Lee HC (1998) Mater Sci Eng A254:29610.1016/S0921-5093(98)00694-7 ↗
15. Hwang LC, Lee S, Lee HC (1998) Mater Sci Eng A254:28210.1016/S0921-5093(98)00626-1 ↗
16. ASTM E8M92 (1990) Standards test methods of tension testing of metallic materials. Annual Book of ASTM Standards, vol. 03.01, pp 130–140
17. ASTM E9, Standards test methods of compression testing of metallic materials at room temperature. Annual Book of ASTM Standards, vol. 03.01, pp 161–168
18. ESIS P2–92 (1992) ESIS procedure for determining the fracture behaviour of materials, European Structural Integrity Society
19. ASTM E399–90 (1995) Standards test methods for plane-strain fracture toughness of metallic materials. Annual Book of ASTM Standards, vol. 03.01, pp 412–442