journal article·2015-02

Modification mechanism of primary silicon by TiB2 particles in a TiB2/ZL109 composite

Jing Sun, Xiaobo Zhang, Yijie Zhang, Naiheng Ma, Haowei Wang

Journal of Materials Science· Volume 50· Issue 3
Publisher page

Abstract

Modification of primary silicon was observed in a hypereutectic Al–Si composite reinforced with TiB2 particles. The primary silicon was found to be refined significantly by TiB2 particles, with the size being reduced from about 25 to 5 μm. Close observation of the microstructure indicates that the TiB2 particles engulfed by the primary silicon acts as the nucleation sites and maintained consistent orientation establishing in primary silicon. According to the experimental results, it was supposed that a few atomic layer of TiSi2 film between the TiB2 and Si would provide good nucleation conditions. According to the critical values for the interatomic spacing misfit, 10 %, along the matching directions and the d-value mismatch, 6 %, between matching planes, the possibility of nucleation is determined by the conventional plane-on-plane model. Furthermore, the edge-to-edge model is used to predict the matching combinations among Si, C54-TiSi2, and TiB2 in detail.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Choi H, Konishi H, Li X (2012) Al2O3 nanoparticles induced simultaneous refinement and modification of primary and eutectic Si particles in hypereutectic Al–20Si alloy. Mater Sci Eng A 541:159–165. doi: 10.1016/j.msea.2012.01.13110.1016/j.msea.2012.01.131 ↗
2. Feng HK, Yu SR, Li YL, Gong LY (2008) Effect of ultrasonic treatment on microstructures of hypereutectic Al–Si alloy. J Mater Process Technol 208(1):330–335. doi: 10.1016/j.jmatprotec.2007.12.12110.1016/j.jmatprotec.2007.12.121 ↗
3. Chirita G, Stefanescu I, Soares D, Silva FS (2009) Influence of vibration on the solidification behaviour and tensile properties of an Al–18 wt% Si alloy. Mater Des 30(5):1575–1580. doi: 10.1016/j.matdes.2008.07.04510.1016/j.matdes.2008.07.045 ↗
4. Zhang XH, Su GC, Ju CW, Wang WC, Yan WL (2010) Effect of modification treatment on the microstructure and mechanical properties of Al–0.35 % Mg–7.0 % Si cast alloy. Mater Des 31:4408–4413. doi: 10.1016/j.matdes.2010.04.03210.1016/j.matdes.2010.04.032 ↗
5. Gökçe A, Fındık F, Kurt AO (2011) Microstructural examination and properties of premixed Al–Cu–Mg powder metallurgy alloy. Mater Charact 62:730–735. doi: 10.1016/j.matchar.2011.04.02110.1016/j.matchar.2011.04.021 ↗
6. Findik F (2012) Improvements in spinodal alloys from past to present. Mater Des 42:131–146. doi: 10.1016/j.matdes.2012.05.03910.1016/j.matdes.2012.05.039 ↗
7. Findik F, Flower HM (1992) Microstructure and hardness development in Cu–30Ni–2·5Cr and Cu–45Ni–10Cr spinodal alloys. Mater Sci Tech 8:197–20510.1179/mst.1992.8.3.197 ↗
8. Findik F, Flower HM (1993) Morphological changes and hardness evolution in Cu–30Ni–5Cr and Cu–45Ni–15Cr spinodal alloys. Mater Sci Tech 9:408–41610.1179/mst.1993.9.5.408 ↗
9. Findik F (1993) Observations on particle size/spacing relationships and phase equilibria in the Cu–Ni–Cr system. J Mater Sci 28:5056–5059. doi: 10.1007/bf0036117810.1007/BF00361178 ↗
10. Gökçe A, Fındık F, Kurt AO (2013) Effects of Mg content on aging behavior of Al4CuXMg PM alloy. Mater Des 46:524–531. doi: 10.1016/j.matdes.2012.10.04510.1016/j.matdes.2012.10.045 ↗
11. Findik F (2002) Modulated Structures in Cu-32Ni-3Cr and Cu-46Ni-17Cr Alloys. Can Metall Quart 41:337–34710.1179/cmq.2002.41.3.337 ↗
12. Liang D, Bayraktar Y, Jones H (1995) Formation and segregation of primary silicon in Bridgman solidification Al-18.3 wt% Si alloy. Acta Metall Mater 43:579–585. doi: 10.1016/0956-7151(94)00287-R10.1016/0956-7151(94)00287-R ↗
13. Wang R-Y, Lu W-H, Hogan LM (1997) Faceted growth of silicon crystals in Al–Si alloys. Metall Mater Trans A 28:1233. doi: 10.1007/s11661-997-0289-x10.1007/s11661-997-0289-x ↗
14. Singh H, Gokhale AM, Tewari A, Zhang S, Mao Y (2009) Three-dimensional visualization and quantitative characterization of primary silicon particles in an Al–Si base alloy. Scripta Mater 61(4):441–444. doi: 10.1016/j.scriptamat.2009.04.04010.1016/j.scriptamat.2009.04.040 ↗
15. Sigworth GK, Alcoa PM (2008) Modification of aluminum-silicon alloys. Int J Metalcast 49:90–104. doi: 10.1361/asmhba0005301
16. Zuo M, Zhao D, Teng X, Geng H, Zhang Z (2013) Effect of P and Sr complex modification on Si phase in hypereutectic Al–30Si alloys. Mater Des 47:857–864. doi: 10.1016/j.matdes.2012.12.05410.1016/j.matdes.2012.12.054 ↗
17. Dai H, Du J, Wang L, Peng C, Liu X (2010) First-principle study of the AlP/Si interfacial adhesion. Physica B Condens Matter 405(2):573–578. doi: 10.1016/j.physb.2009.09.06810.1016/j.physb.2009.09.068 ↗
18. Yu L, Liu X, Ding H, Bian X (2007) A new nucleation mechanism of primary Si by peritectic-like coupling of AlP and TiB2 in near eutectic Al-Si alloy. J Alloys Compd 432:156–162. doi: 10.1016/j.jallcom.2006.06.00510.1016/j.jallcom.2006.06.005 ↗
19. Liu X, Wu Y, Bian X (2005) The nucleation sites of primary Si in Al–Si alloys after addition of boron and phosphorus. J Alloy Compd 391(1–2):90–94. doi: 10.1016/j.jallcom.2004.09.00310.1016/j.jallcom.2004.09.003 ↗
20. Mizutani Y, Kawai S, Miwa K, Yasue K, Tamura T, Sakaguchi Y (2004) Effect of the intensity and frequency of electromagnetic vibrations on refinement of primary silicon in Al-17 % Si alloy. Mater Trans 45(6):1939–1943. doi: 10.2320/matertrans.45.193910.2320/matertrans.45.1939 ↗
21. Böttger B, Eiken J, Steinbach I (2006) Phase field simulation of equiaxed solidification in technical alloys. Acta Metall Mater 54:2697–2704. doi: 10.1016/j.actamat.2006.02.00810.1016/j.actamat.2006.02.008 ↗
22. Yi H, Ma N, Li X, Zhang Y, Wang H (2006) High-temperature mechanics properties of in situ TiB 2p reinforced Al–Si alloy composites. Mater Sci Eng A 419(1):12–17. doi: 10.1016/j.msea.2005.10.02010.1016/j.msea.2005.10.020 ↗
23. Zhou S, Liu X, Wang D (2010) Si/TiSi2 heteronanostructures as high-capacity anode material for Li ion batteries. Nano Lett 10:860–863. doi: 10.1021/nl903345f10.1021/nl903345f ↗
24. Zhu Y, Zhao D, Li R, Liu J (2006) Self-aligned TiSi2/Si heteronanocrystal nonvolatile memory. Appl Phys Lett 88(10):103507–103510. doi: 10.1063/1.218381510.1063/1.2183815 ↗
25. Catana A, Schmid PE, Heintze M, Lévy F, Stadelmann P, Bonnet R (1990) Atomic scale study of local TiSi2/Si epitaxies. J Appl Phys 67(4):1820–1825. doi: 10.1063/1.34560910.1063/1.345609 ↗
26. Ting CY, Wittmer M (1983) Investigation of the Al/TiSi2/Si contact system. J Appl Phys 54(2):937–943. doi: 10.1063/1.33201810.1063/1.332018 ↗
27. Li P, Li Y, Wu Y, Ma G, Liu X (2012) Distribution of the TiB2 particles and its effect on the mechanical properties of A390 alloy. Mater Sci Eng A 546:146–152. doi: 10.1016/j.msea.2012.03.04210.1016/j.msea.2012.03.042 ↗
28. Zhang MX, Kelly PM (2005) Edge-to-edge matching and its applications Part: application to the simple HCP/BCC system. Acta Mater 53:1073–1084. doi: 10.1016/j.actamat.2004.11.00710.1016/j.actamat.2004.11.007 ↗
29. Zhang MX, Kelly PM (2005) Edge-to-edge matching and its applications: part II. Application to Mg–Al, Mg–Y and Mg–Mn alloys. Acta Mater 53(4):1085–1096. doi: 10.1016/j.actamat.2004.11.00510.1016/j.actamat.2004.11.005 ↗
30. Zhang MX, Kelly PM, Qian M, Taylor JA (2005) Crystallography of grain refinement in Mg–Al based alloys. Acta Mater 53(11):3261–3270. doi: 10.1016/j.actamat.03.03010.1016/j.actamat.2005.03.030 ↗
31. Qiu D, Taylor JA, Zhang MX, Kelly PM (2007) A mechanism for the poisoning effect of silicon on the grain refinement of Al–Si alloys. Acta Mater 55(4):1447–1456. doi: 10.1016/j.actamat.2006.09.04610.1016/j.actamat.2006.09.046 ↗
32. Zhang MX, Kelly PM, Easton MA, Taylor JA (2005) Crystallographic study of grain refinement in aluminum alloys using the edge-to-edge matching model. Acta Mater 53(5):1427–1438. doi: 10.1016/j.actamat.2004.11.03710.1016/j.actamat.2004.11.037 ↗
33. Zhang WZ, Weatherly GC (1998) A comparative study of the theory of the O-lattice and the phenomenological theory of martensite crystallography to phase transformations. Acta Mater 46(6):1837–1847. doi: 10.1016/S1359-6454(97)00435-710.1016/S1359-6454(97)00435-7 ↗
34. Ye F, Zhang WZ (2002) Coincidence structures of interfacial steps and secondary misfit dislocations in the habit plane between Widmanstätten cementite and austenite. Acta Mater 50(11):2761–2777. doi: 10.1016/S1359-6454(02)00077-010.1016/S1359-6454(02)00077-0 ↗
35. Furuhara T, Howe JM, Aaronson HI (1991) Interphase boundary structures of intragranular proeutectoid α plates in a hypoeutectoid Ti–Cr alloy. Acta Metall Mater 39(11):2873–2886. doi: 10.1016/0956-7151(91)90104-910.1016/0956-7151(91)90104-9 ↗
36. Ye F, Zhang WZ, Qiu D (2004) A TEM study of the habit plane structure of intragrainular proeutectoid α precipitates in a Ti-7.26 wt% Cr alloy. Acta Mater 52(8):2449–2460. doi: 10.1016/j.actamat.2004.01.03710.1016/j.actamat.2004.01.037 ↗
37. Kelly PM, Zhang MX (2005) Comments on edge-to-edge matching and the equivalence of the invariant line, Δg and Moiré Fringe approaches to the crystallographic features of precipitates. Scripta Mater 52:679–682. doi: 10.1016/j.scriptamat.2004.11.03010.1016/j.scriptamat.2004.11.030 ↗
38. Mann RW (1994) The C49 to C54 phase transformation in TiSi2 thin films. J Electrochem Soc 141(5):1347–1350. doi: 10.1149/1.205492110.1149/1.2054921 ↗
39. Chou TC, Wong CY, Tu KN (1987) Lattice imaging of metastable TiSi2. J Appl Phys 62(6):2275–2279. doi: 10.1063/1.33948310.1063/1.339483 ↗
40. Ravindran P, Fast L, Korzhavyi PA, Johansson B, Wills J, Eriksson O (1998) Density functional theory for calculation of elastic properties of orthorhombic crystals: application to TiSi2. J Appl Phys 84(9):4891–4904. doi: 10.1063/1.36873310.1063/1.368733 ↗
41. Kim J, Posadas A, Dargis R, Choi M, Demkov A, Smith D (2011) Formation of single-orientation epitaxial Islands of TiSi2 on Si (001) using Sr passivation. Microsc Microanal 17:1330–1335. doi: 10.1017/s143192761100752510.1017/S1431927611007525 ↗
42. Merwe JHvd (1982) Analytical selection of ideal epitaxial configurations and some speculations on the occurrence of epitaxy I. Epitaxy with rectangular interfacial atomic meshes. Philos Mag A 45(1):127–143. doi: 10.1080/0141861820824390710.1080/01418618208243907 ↗
43. Kelly PM, Zhang MX (2006) Edge-to-edge matching-the fundamentals. J Metall Mater Trans A 37(3):833–839. doi: 10.1007/s11661-006-1003-010.1007/s11661-006-0056-4 ↗
44. Hall MG, Aaronson HI, Kinsma KR (1972) The structure of nearly coherent fcc: bcc boundaries in a Cu–Cr alloy. Surf Sci 31:257–274. doi: 10.1016/0039-6028(72)90264-610.1016/0039-6028(72)90264-6 ↗
45. Fujii T, Mori T, Kato M (1992) Crystallography and morphology of needle-like α-Fe precipitate particles in a Cu matrix. Acta Metall Mater 40(12):3413–3420. doi: 10.1016/0956-7151(92)90055-J10.1016/0956-7151(92)90055-J ↗
46. Duly D (1993) Application of the invariant line model for bcc/hcp couples: a criterion based on surface variations. Acta Metall Mater 41(5):1559–1566. doi: 10.1016/0956-7151(93)90264-S10.1016/0956-7151(93)90264-S ↗