Influence of coated SiC particulates on the mechanical and magnetic behaviour of Fe–Co alloy composites
Source abstract
Abstract
Near-equiatomic Fe–Co alloy composites containing 0, 5 and 10 vol% of uncoated and coated SiC particles were prepared by applying a uniaxial pressure of 80 MPa at 900 °C for 5 min in a spark plasma sintering furnace. The SiC particles used in this study were coarse, with an average particle size of 20 μm and their surfaces were coated with four different types of coatings, namely Ni–P, Cu, Co and duplex Cu and Ni–P by an electroless plating method. Quasi D.C. magnetic, bending and hardness tests were performed on the composites. The influence of particulate coatings on the magnetic and mechanical behaviour of the composites was investigated by correlating their properties with their microstructures as observed using scanning electron microscopy and optical microscopy and crystallographic information as obtained using X-ray diffraction. The cobalt coated particles were found to exhibit the best wettability with the matrix without the formation of deleterious intermetallic compounds at the interface. Because of the better interfacial bonding in the composites with Co coated particles, there was an enhancement in flexural strength and permeability compared to the uncoated and other coated particulate composites studied. In addition, inclusion of cobalt coated SiC particulates produced an increase in hardness and a decrease in coercivity compared to the monolithic material.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Electrodeposition and Electroless Coatings · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (32)
Show source-provided references
1. Quigley RE (1993) More electric aircraft. In: Proceedings of IEEE applied power electronics conference, San Diego, CA, March 1993, pp 906–91110.1109/APEC.1993.290667 ↗
2. Fingers RT, Coate JE, Dowling RE (1997) Mechanical properties of iron-cobalt alloys for power applications. In: Proceedings of the 32nd intersociety energy conversion engineering conference, vol 4, pp 563–56810.1109/IECEC.1997.659251 ↗
3. Sundar RS, Deevi SC (2005) Soft magnetic FeCo alloys: alloy development, processing, and properties. Int Mater Rev 50:157–19210.1179/174328005X14339 ↗
4. Kawahara K (1983) Effect of carbon on mechanical properties in Fe0·5Co0·5 alloys. J Mater Sci 18:2048–2055. doi: 10.1007/BF00554997
5. Persiano AIC, Rawlings RD (1991) Effect of niobium additions on the structure and magnetic properties of equiatomic iron-cobalt alloys. J Mater Sci 26:4026–4032. doi: 10.1007/BF0240294310.1007/BF02402943 ↗
6. Fielder HC, Davies AM (1970) The formation of gamma phase in Vanadium Permendur. Metall Trans 1:1036–103710.1007/BF02811792 ↗
7. Kawahara K (1983) Effect of additive elements on cold workability in FeCo alloys. J Mater Sci 18:1709–1718. doi: 10.1007/BF0054206610.1007/BF00542066 ↗
8. Sourmail T (2005) Near equiatomic FeCo alloys: constitution, mechanical and magnetic properties. Prog Mater Sci 50:816–88010.1016/j.pmatsci.2005.04.001 ↗
9. Doel TJA, Bowen P (1996) Tensile properties of particulate-reinforced metal matrix composites. Compos A 27A:655–66510.1016/1359-835X(96)00040-1 ↗
10. Chawla N, Shen Y-L (2001) Mechanical behavior of particle reinforced metal matrix composites. Adv Eng Mater 3:357–37010.1002/1527-2648(200106)3:6<357::AID-ADEM357>3.0.CO;2-I ↗
11. Abdullah Y, Daud AR, Shamsudin R, Harun MB (2009) Flexural strength and fracture studies of Al–Si/SiCp composites. Int J Mech Mater Eng 4:109–114
12. Pagounis E, Talvitieb M, Lindroos VK (1996) Influence of the metal/ceramic interface on the microstructure and mechanical properties of HIPed iron based composites. Compos Sci Technol 56:1329–133710.1016/S0266-3538(96)00101-7 ↗
13. Clyne TW, Jones FR (2001) Composites: interfaces in encyclopaedia of materials: science and technology. In: Mortensen A (ed) 3.7.17 “Composites: MMC, CMC, PMC”. Elsevier, Amsterdam
14. Rajan TPD, Pillai RM, Pai BC (1998) Reinforcement coatings and interfaces in aluminium metal matrix composites. J Mater Sci 33:3491–3503. doi: 10.1023/A:100467482275110.1023/A:1004674822751 ↗
15. Sahoo P, Das SK (2011) Tribology of electroless nickel coatings—a review. Mater Des 32:1760–177510.1016/j.matdes.2010.11.013 ↗
16. Girot FA, Quenisset JM, Naslain R (1987) Discontinuously reinforced Al-matrix composites. Comp Sci Tech 30:155–18410.1016/0266-3538(87)90007-8 ↗
17. Sharma R, Agarwala RC, Agarwala V (2006) Development of copper coatings on ceramic powder by electroless technique. Appl Surf Sci 252:8487–849310.1016/j.apsusc.2005.11.085 ↗
18. Li LB, An MZ, Wu GH (2005) Electroless deposition of nickel on the surface of silicon carbide/aluminum composites in alkaline bath. Mater Chem Phys 94:159–16410.1016/j.matchemphys.2005.04.038 ↗
19. Jiang JT, Zhen L, Xu CY, Shao WZ (2007) Microstructure evolution of cobalt coating electroless plated on SiC whisker during electroless plating and heat treatment. Surf Coat Technol 201:6059–606210.1016/j.surfcoat.2006.10.032 ↗
20. Mani MK, Viola G, Reece MJ, Hall JP, Evans SL (2012) Structural and magnetic characterization of spark plasma sintered Fe–50Co alloys. Mater Res Symp Proc 1516:201–20710.1557/opl.2012.1669 ↗
21. Anderson P (2008) A universal DC characterisation system for hard and soft magnetic materials. J Magn Magn Mater 320:e589–e59310.1016/j.jmmm.2008.04.034 ↗
22. International Standards Organization (1995) ISO 6872: dental ceramic. ISO, Geneva
23. Song JY, Yu J (2002) Residual stress measurements in electroless plated Ni–P films. Thin Solid Films 415:167–17210.1016/S0040-6090(02)00556-4 ↗
24. Hentschel TH, Isheim D, Kirchheim R, Müller F, Kreye H (2000) Nanocrystalline Ni-3.6 at.% P and its transformation sequence studied by atom-probe field-ion microscopy. Acta Mater 48:933–94110.1016/S1359-6454(99)00371-7 ↗
25. Clegg DW, Buckley RA (1973) The disorder-order transformation in iron–cobalt-based alloys. Met Sci J 7:48–5410.1179/030634573790445541 ↗
26. Hanejko F, Rutz H, Oliver C (1992) Effects of processing and materials on soft magnetic performance of powder metallurgy parts: advances in powder metallurgy & particulate materials, vol 6. Metal Powder Industries Federation, Princeton, pp 375–404
27. Goldman JE, Smoluchowski R (1949) Influence of order on the saturation magnetic moment. Phys Rev 75:310–31110.1103/PhysRev.75.310.2 ↗
28. Niculesu V, Burch TJ, Raj K, Budnick JI (1977) Properties of Heuler-type materials Fe2TSi and FeCo2Si. J Magn Magn Mater 5(1):60–6610.1016/0304-8853(77)90197-4 ↗
29. Orrock CM (1986) PhD Thesis, London University
30. Jordan KR, Stoloff NS (1969) Plastic deformation and fracture in FeCo–2%V. Trans Metall Soc AIME 245:2027–2034
31. Johnston TL, Davies RG, Stoloff NS (1965) Slip character and the ductile to brittle transition of single phase solids. Philos Mag 12:305–31710.1080/14786436508218873 ↗
32. Zhao L, Baker I, George EP (1993) Room temperature fracture of FeCo. Mater Res Symp Proc 288:501–50610.1557/PROC-288-501 ↗