The ESC behaviour of a toughened PMMA after exposure to gamma radiation
Source abstract
Abstract
This work is a sequence of a previous one where we investigated the influence of gamma radiation dose on environmental stress cracking (ESC) of a conventional poly(methyl methacrylate) (PMMA) (Sousa et al. Polym Degrad Stab 92:1465, 2007). In that work, we observed that low doses of gamma radiation intensified the ESC effects, but on higher doses the gamma radiation effect was predominant over the stress cracking. The present work describes a similar study, but using a toughened PMMA (t-PMMA). The polymer was submitted to gamma radiation doses up to 100 kGy, and then tested to ESC susceptibility through tensile and relaxation tests. Two different types of active fluids were used: ethanol (an aggressive one) and ethylene glycol (a moderate liquid stress cracking agent), based on absorption results. A synergistic effect between ESC and radiation degradation was noted, with a substantial decay in mechanical properties when these two effects were present. The ethanol action caused dendritic pattern formation in the fracture surfaces of t-PMMA, as revealed by scanning electron microscopy.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Polymer crystallization and properties · Mechanical Behavior of Composites · Polymer Nanocomposites and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. Navarro RF, d’Almeida JRM, Rabello MS (2007) J Mater Sci 42:2167. doi: https://doi.org/10.1007/s10853-006-1387-710.1007/s10853-006-1387-7 ↗
2. Rabello MS, White JR (1996) Polym Comp 17:69110.1002/pc.10661 ↗
3. Brostow W, Corneliussen H (1986) Failure of plastics. Hanser, Munich
4. Wright DC (1996) Environmental stress cracking of plastics. Rapra, Shawbury
5. Kawaguchi T, Nishimura H (2003) Polym Eng Sci 43:41910.1002/pen.10034 ↗
6. Al-Saidi LF, Mortensen K, Almdal K (2003) Polym Degrad Stab 82:45110.1016/S0141-3910(03)00199-X ↗
7. Sousa AR, Araujo ES, Carvalho AL, Rabello MS, White JR (2007) Polym Degrad Stab 92:146510.1016/j.polymdegradstab.2007.05.008 ↗
8. Kjellander CK, Nielsen TB, Kingshott P, Ghanbari-Siahkali A, Hansen CM, Almdal K (2008) Polym Degrad Stab 93:148610.1016/j.polymdegradstab.2008.05.011 ↗
9. Sousa AR, Amorim KL, Medeiros ES, Melo TJA, Rabello MS (2006) Polym Degrad Stab 91:150410.1016/j.polymdegradstab.2005.10.002 ↗
10. Timoteo GAV, Fechine GJM, Rabello MS (2007) Macromol Symp 258:16210.1002/masy.200751218 ↗
11. Timoteo GAV, Fechine GJM, Rabello MS (2008) Polym Eng Sci 48:200310.1002/pen.21067 ↗
12. Rabello MS (2000) Aditivação de Polímeros. Artliber Editora, São Paulo
13. Biwa S, Ito N, Ohno N (2001) Mech Mater 33:71710.1016/S0167-6636(01)00087-4 ↗
14. Argon AS, Cohen N (2003) Polymer 44:601310.1016/S0032-3861(03)00546-9 ↗
15. Lin CB, Lee S (1992) J Appl Polym Sci 44:221310.1002/app.1992.070441218 ↗
16. Bernier GA, Kambour RP (1968) Macromolecules 1:39310.1021/ma60005a005 ↗
17. Arnold JC (1998) J Mater Sci 33:5193. doi: https://doi.org/10.1023/A:100443192044910.1023/A:1004431920449 ↗
18. Sperling LH (1986) Introduction to physical polymer science. Wiley, New York
19. Suarez JCM, Blasi RSDE (2003) Polym Degrad Stab 82:22110.1016/S0141-3910(03)00212-X ↗
20. Ciuprina F, Teissedre G, Filippini JC (2001) Polymer 42:784110.1016/S0032-3861(01)00264-6 ↗
21. Meyer CT, Filippini JC (1979) Polymer 20:118610.1016/0032-3861(79)90140-X ↗