journal article·2010-05

Effect of magnesium content on thermal and structural parameters of Al–Mg alloys directionally solidified

Jean Robert Pereira Rodrigues, Mirian de Lourdes Noronha Motta Melo, Rezende Gomes dos Santos

Journal of Materials Science· Volume 45· Issue 9
Publisher page

Abstract

In this study, the influence of magnesium content on thermal and structural parameters during the unsteady-state unidirectional solidification of Al–Mg alloys is analyzed. Using a special device, Al–Mg alloys containing 5, 10, and 15 wt% Mg were submitted to unidirectional solidification. Using a data acquisition system, the temperature variations along the casting during solidification were measured. From these results, the variations of solidification parameters as growth rate of dendrite tips, thermal gradient, cooling rate, and local solidification time were determined. The variation of global heat transfer coefficient at metal/mould interface was estimated through the adjustment of experimental temperature variation close to the interface and numerical predictions. Primary and secondary dendrite arms spacing variations during solidification were measured by optical microscopy. From these results, comparative analysis were developed to determine the influence of magnesium content.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Solidification and crystal growth phenomena · Metallurgical Processes and Thermodynamics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. Kurz W, Fisher DJ (1992) Fundamentals of solidification. Trans Tech, Aedermannsdorf
2. Flemings MC (1974) Solidification processing. McGraw-Hill, New York
3. Bouchard D, Kirkaldy JS (1997) Metall Mater Trans B 28B:65110.1007/s11663-997-0039-x ↗
4. Melo MLNM, Rizzo EMS, Santos RG (2005) J Mater Sci 40:1599. doi: 10.1007/s10853-005-0659-y10.1007/s10853-005-0659-y ↗
5. Melo MLNM, Rizzo EMS, Santos RG (2004) Mater Sci Eng A 374:35110.1016/j.msea.2004.03.009 ↗
6. Rocha OL, Siqueira CA, Garcia A (2003) Mater Sci Eng A 347:5910.1016/S0921-5093(02)00581-6 ↗
7. Rocha OL, Siqueira CA, Garcia A (2003) Metall Mater Trans A 34A:99510.1007/s11661-003-0229-3 ↗
8. Gündüz M, Çadirli E (2002) Mater Sci Eng A 327:16710.1016/S0921-5093(01)01649-5 ↗
9. Whitesell HS, Overfelt RA (2001) Mater Sci Eng A 318:26410.1016/S0921-5093(01)01264-3 ↗
10. Lin X, Huang W, Feng J, Li T, Zhou Y (1999) Acta Mater 47:327110.1016/S1359-6454(99)00166-4 ↗
11. Henry S, Minghetti T, Rappaz M (1998) Acta Mater 46:643110.1016/S1359-6454(98)00308-5 ↗
12. Taler J (1992) Trans ASME 114:104810.1115/1.2911877 ↗
13. Rappaz M, Stefanescu DM (1988) Metals handbook, vol 15. ASM, Ohio
14. Scheil E (1942) Zeitschrift fur Metalkunde 34:70
15. Pehlke RD, Jeyarajan A, Wada H (1982) Summary of thermal properties of casting alloys and mold materials. University of Michigan, Ann Arbor
16. Sharp RM, Hellawell A (1969) J Cryst Growth 5:15510.1016/0022-0248(69)90001-3 ↗
17. Okamoto T, Kishitake K (1975) J Cryst Growth 29:13710.1016/0022-0248(75)90217-1 ↗
18. Hunt JD (1979) Solidification and casting of metals. The Metals Society, London
19. Kurz W, Fisher JD (1981) Acta Metall 29:1110.1016/0001-6160(81)90082-1 ↗
20. Trivedi R (1984) Metall Mater Trans A 15A:97710.1007/BF02644689 ↗
21. Geying A, Lixin L (1987) J Cryst Growth 80:38310.1016/0022-0248(87)90085-6 ↗
22. Jones H (1984) Proceedings of solidification processing, Sheffield, p 349
23. Feurer U (1977) Proceedings of the symposium on quality control of engineering alloys, Delft, p 131
24. Kirkwood DH (1985) Mater Sci Eng 73:5110.1016/0025-5416(85)90319-2 ↗