Quantifying the dispersion of carbon nanotubes in thermoplastic-toughened epoxy polymers
Source abstract
Abstract
The distribution of particles within modern materials must be defined to understand the change in properties attained by their addition. Two methods of analysis, which use different size scales, are presented here. These methods are applied to characterise the dispersion of multi-walled carbon nanotubes in a thermoplastic-toughened epoxy polymer. First, the greyscale method uses transmission optical micrographs, and calculates the ratio of the variance/mean of the greyscale values. Higher values indicate a greater degree of clustering; lower values may be described as showing a ‘better’ distribution of nanotubes, hence allowing the results to be ranked. This method is relatively easier to carry out, but care must be taken to use a consistent small thickness of sample. Secondly, the quadrat analysis uses transmission electron micrographs of the same materials, after identifying the centre of each nanotube observed. This defines the distribution on the scale of the nanotubes. Peaks in the relationship between the ratio of the variance/mean and cell size are related to microstructural features such as agglomeration. This scale is expected to be related to the scale of microstructural deformation mechanisms which determine global material properties.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Carbon Nanotubes in Composites · Polymer crystallization and properties · Force Microscopy Techniques and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. Iijima S (1991) Nature 354:5610.1038/354056a0 ↗
2. Xie X-L, Mai Y-W, Zhou X-P (2005) Mater Sci Eng R 49:8910.1016/j.mser.2005.04.002 ↗
3. Hsiao K-T, Alms J, Advani SG (2003) Nanotechnology 14:79110.1088/0957-4484/14/7/316 ↗
4. Ganguli S, Bhuyan M, Allie L, Aglan H (2005) J Mater Sci 40:3593. doi: 10.1007/s10853-005-2891-x10.1007/s10853-005-2891-x ↗
5. Liu L-Q, Wagner HD (2007) Compos Interfaces 14:28510.1163/156855407780452904 ↗
6. Hernández-Pérez A, Avilés F, May-Pat A, Valadez-González A, Herrera-Franco PJ, Bartolo-Pérez P (2008) Compos Sci Technol 68:142210.1016/j.compscitech.2007.11.001 ↗
7. Wang Z, Liang ZY, Wang B, Zhang C, Kramer L (2004) Composites A 35:122510.1016/j.compositesa.2003.09.029 ↗
8. Song YS, Youn JR (2005) Carbon 43:137810.1016/j.carbon.2005.01.007 ↗
9. Lau K-T, Shi S-Q, Cheng H-M (2003) Compos Sci Technol 63:116110.1016/S0266-3538(03)00038-1 ↗
10. Fiedler B, Gojny FH, Wichmann MHG, Nolte MCM, Schulte K (2006) Compos Sci Technol 66:311510.1016/j.compscitech.2005.01.014 ↗
11. Gershon A, Cole D, Kota A, Bruck H (2010) J Mater Sci 45:6353. doi: 10.1007/s10853-010-4597-y10.1007/s10853-010-4597-y ↗
12. Gong X, Liu J, Baskaran S, Voise RD, Young JS (2000) Chem Mater 12:104910.1021/cm9906396 ↗
13. Guild FJ, Summerscales J (1998) In: Summerscales J (ed) Microstructural characterisation of fibre-reinforced composites. Woodhead Publishing, Cambridge
14. Chatfield C (1983) Statistics for technology: a course in applied statistics. CRC Press, Boca Raton
15. Thomas Swan (2006) Technical Data Sheet, Elicarb MW (Dry). Thomas Swan & Co., Consett
16. Brooker RD (2009) PhD Thesis, Imperial College London, London
17. Brooker RD, Kinloch AJ, Taylor AC (2010) J Adhesion 86:726. doi: 10.1080/00218464.2010.48241510.1080/00218464.2010.482415 ↗
18. Guild FJ, Silverman BW (1978) J Microsc Oxf 114:13110.1111/j.1365-2818.1978.tb00125.x ↗
19. Held G (2009) Introduction to light emitting diode technology and applications. Auerbach Publications, Boca Raton
20. Sawyer LC, Grubb DT, Meyers GF (2008) Polymer microscopy. Springer, New York
21. Masania K (2010) PhD Thesis, Imperial College London, London
22. Hsieh TH, Kinloch AJ, Masania K, Taylor AC, Sprenger S (2010) Polymer 51:6284. doi: 10.1016/j.polymer.2010.10.04810.1016/j.polymer.2010.10.048 ↗