journal article·2004-05

The thermo-mechanical behaviour of Cu-Cr in-situ composite

K. L. Lee

Journal of Materials Science· Volume 39· Issue 9
Publisher page

Abstract

The mechanical response of in-situ copper-chromium composite was modelled using a deformation mechanism map approach. The stresses in each phase were predicted as a function of temperature and strain rate. From this the ratio of phase stresses, and hence the degree of load transfer, was obtained. The extent of load transfer and the predicted deformation modes of the two phases were then related to the expected failure mechanisms of the composite. Three modes of composite failure were predicted. Copper-chromium in-situ composites, and pure copper, were produced by a casting and swaging route. The mechanical properties were then characterised experimentally by tensile testing. Mechanical tests confirmed that the composite showed significantly higher strength than the unreinforced material. The observed failure modes of the composite were compared with the predictions.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. K. L. Lee, H. E. Carroll and A. F. Whitehouse, Mater. Sci. Tech. 16 (2000) 811.10.1179/026708300101508487 ↗
2. K. L. Lee, A. F. Whitehouse, P. J. Withers and M. R. Daymond, Mater. Sci. Eng. A 348 (2003) 208.10.1016/S0921-5093(02)00688-3 ↗
3. K. L. Lee, A. F. Whitehouse, S. I. Hong and A. M. Russell, Accepted for publication in Metal & Mater Trans A vol. 35A, p. 695.10.1007/s11661-004-0380-5 ↗
4. K. L. Lee, A. F. Whitehouse and A. C. F. Cocks, ICCM 12 Paris (1999).
5. K. L. Lee, Composites: Part A. 34(12) (2003) 1235.10.1016/S1359-835X(03)00251-3 ↗
6. S. I. Hong, M. A. Hill, Y. Sakai, J. T. Wood and J. D. Embury, Acta Metall. Mater. 43(9) (1995) 3313.10.1016/0956-7151(95)00050-6 ↗
7. J. D. Verhoeven, W. A. Spitzig, L. L. Jones, H. L. Downing, C. L. Trybus, E. D. Gibson, L. S. Chumbley, L. G. Fritzemeier and G. D. Schnittgrund, J. Mater. Eng. 12(2) (1990) 127.10.1007/BF02834066 ↗
8. T. W. Ellis, S. T. Kim and J. D. Verhoeven, J. Mater. Engng. Perform. 4 (1995) 581.10.1007/BF02649590 ↗
9. C. Biselli and D. G. Morris, Mater. Sci. Eng. A 148(2) (1991) 163.10.1016/0921-5093(91)90818-8 ↗
10. Y. Jin, K. Adachi, T. Takeuchi and H. G. Suzuki, ibid. 212(1) (1996) 149.10.1016/0921-5093(96)10194-5 ↗
11. Idem., Metal. Mater. Trans. A 29(8) (1998) 2195.10.1007/s11661-998-0044-y ↗
12. H. J. Frost and M. F. Ashby, “Deformation Mechanism Maps—The Plasticity and Creep of Metals and Ceramics” (Oxford, Pergamon, 1982) p. 161.
13. D. L. Zhang, K. Mihara, E. Takakura and H. G. Suzuki, Mater. Sci. Eng. A 266(1/2) (1999) 99.
14. M. F. Ashby, Acta Metall. 20 (1972) 887.10.1016/0001-6160(72)90082-X ↗
15. K. L. Lee, A. F. Whitehouse, A. M. Russell, K. Wongpreedee, S. I. Hong and P. J. Withers, J. Mater. Sci. 38 (2003) 3437.10.1023/A:1025196700785 ↗
16. K. L. Lee, J. Quinta Da Fonseca, P. J. Withers, S. I. Hong and A. M. Russell, submitted to Scripta Mater.