SIMS analysis of low content hydrogen in commercially pure titanium
Source abstract
Abstract
Due to their excellent specific strength and environmental resistance, titanium and its alloys have been widely used as structural components. However, titanium is very active, so that not only oxygen and nitrogen, but also hydrogen may be readily introduced into the material during manufacturing. Titanium usually contains a specific amount of hydrogen, and it exists in the titanium as a hydride or solid solution dependent on the hydrogen content. The hydrogen solid solubility limit of pure titanium (a-phase titanium) seems to be higher than 10 ppm [1], although some values are reported. That is to say, if the hydrogen content of pure titanium is less than 10 ppm, all the hydrogen is thought to be a solid solution in the titanium. On the other hand, when the hydrogen content is more than the solid solubility limit, hydrides would appear. As the hydride is brittle, it weakens the strength of the titanium. Therefore, the hydrogen content in commercially pure titanium (CP-Ti) is within 150 ppm [2]. The present authors carried out a fatigue strength evaluation of titanium samples using the hydrogen removed sample (hydrogen content is 2.7 ppm) and normal sample (34 ppm) [3, 4]. On the surface of the 2.7 ppm one, the hydride did not exist, while on the 34 ppm one, the hydride was present. It was found that the fatigue crack nucleation life of the 34 ppm one is greater than that of the 2.7 ppm one, and the fatigue crack propagation life of the 34 ppm one is the same as the 2.7 ppm one. This specific observation of the crack propagation indicated that the material behavior near the grain boundary is important for the crack propagation [3, 4]. It is then important to understand the actual state of hydrogen near the grain boundary for the CP-Ti applications. There are some methods to detect hydrogen in materials, and each method has some merits and demerits. The hydrogen thermal desorption analysis method (TDS and TDA) can be used for the average hydrogen content and energy state analysis [5]. As already mentioned, hydrogen in the CP-Ti exists as a solid solution or hydride, and the hydrogen localized around the grain boundary should be evaluated. The localized hydrogen can then be visualized by the following method.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Materials Characterization Techniques · Hydrogen embrittlement and corrosion behaviors in metals · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Lenning GA, Craighead CM, Jaffee RI (1954) Trans AIME 200:367
2. Donachie MJ Jr (1988) TITANIUM: a technical guide. ASM International, USA, pp 8, 27, 209
3. Nishikawa H, Oda Y, Noguchi H (2007) Memoirs Faculty Eng Kyushu Univ 67:181
4. Nishikawa H, Oda Y, Noguchi H (2008) In: Proceedings of 17th European conference fracture, pp 1289–1296
5. Takai K (2004) Trans Jpn Soc Mech Eng A 70:102710.1299/kikaia.70.1027 ↗
6. Ladna B, Birnbaum HK (1987) Acta Metallurg 35:253710.1016/0001-6160(87)90150-7 ↗
7. Degréve F, Thorne NA, Lang JM (1988). J Mater Sci 23: 4181. doi: 10.1007/BF0055190910.1007/BF00551909 ↗
8. Takeshita H, Suzuki R, Ono K (1994) Materia Japan 33:35610.2320/materia.33.356 ↗
9. Okuno K (1994) Materia Japan 33:36210.2320/materia.33.362 ↗
10. Takai K, Chiba Y, Noguchi K, Nozue A (2002) Metallurg Mater Trans A 33:265910.1007/s11661-002-0387-8 ↗
11. Yan L, Ramamurthy S, Noël JJ, Shoesmith DW (2006) Electrochim Acta 52:116910.1016/j.electacta.2006.07.017 ↗
12. Kawamoto K, Oda Y, Noguchi H, Fujii H, Izumi T, Itoh G (2007) Trans Jpn Soc Mech Eng A 73:78810.1299/kikaia.73.788 ↗
13. Pérez TE, García JO (1982) Scr Metallurg 16:16110.1016/0036-9748(82)90377-5 ↗
14. García JO (1985) J Mater Sci 20:2623. doi: 10.1007/BF0055609410.1007/BF00556094 ↗
15. Ichitani K, Kanno M, Kuramoto S (2003) ISIJ Int 43:49610.2355/isijinternational.43.496 ↗
16. Laurent JP, Lapasset G (1973) Int J Appl Radiat Isot 24:21310.1016/0020-708X(73)90044-6 ↗
17. Asaoka T, Lapasset G, Aucouturier M, Lacombe P (1978) Corrosion 34:3910.5006/0010-9312-34.2.39 ↗
18. Ilić R, Altstetter C (1981) Nucl Instrum Methods 185:50510.1016/0029-554X(81)91248-9 ↗
19. Wagner R (1982) Materials science (Crystals Vol. 6) Chapter Field-ion microscopy. Springer, Berlin10.1007/978-3-642-68687-0 ↗
20. Miller MK (2000) Atom probe tomography: analysis at atomic level. Kluwer Academic, New York10.1007/978-1-4615-4281-0 ↗
21. Numakura H, Koiwa M (1984) Acta Metallurg 32:179910.1016/0001-6160(84)90236-0 ↗
22. Shih DS, Robertson IM, Birnbaum HK (1988) Acta Metallurg 36:11110.1016/0001-6160(88)90032-6 ↗
23. Zhang C, Kang Q, Lai Z (1994) Acta Metallurg Mater 42:255510.1016/0956-7151(94)90336-0 ↗
24. Chen CQ, Li SX, Lu K (2003) Acta Mater 51:93110.1016/S1359-6454(02)00495-0 ↗
25. Chen CQ, Li SX (2004) Mater Sci Eng A 387-389:47010.1016/j.msea.2004.01.117 ↗
26. Luppo MI, Politi A, Vigna G (2005) Acta Mater 53:498710.1016/j.actamat.2005.06.004 ↗
27. Miwa S, Nomachi I, Kitajima H (2006) Appl Surf Sci 252:731810.1016/j.apsusc.2006.02.168 ↗
28. Cameca Web Site, “IMS 7f Applications”. http://www.cameca.fr/html/ims_7f_applications.html . Accessed 1 July 2009
29. Odom RW, Furman BK, Evans CA, Bryson CE, Petersen WA, Kelly MA, Wayne DH (1977) Anal Chem 55:57410.1021/ac00254a036 ↗
30. Nishikawa H, Hamada S, Ohnishi K (2007) Memoirs Faculty Eng Kyushu Univ 67:191