journal article·2009-10

Precipitation hardening of Zr-modified Mg–Ca–Zn alloy

D. Shepelev, M. Bamberger, A. Katsman

Journal of Materials Science· Volume 44· Issue 20
Publisher page

Abstract

The microstructure and mechanical properties of Mg–Ca–Zn alloys with 1 wt.% Zr were investigated in as-cast and heat-treated conditions. A substantial decrease in grain size (from 65 µm for the Mg–Ca–Zn base alloy to 22 µm) was observed. The alloy was solution treated at 410 °C for up to 96 h followed by aging at 175 °C for up to 24 h. Conventional techniques, X-ray diffraction, EM + EDS, and TEM were used to characterize the microstructure of the alloy. The microstructure obtained after heat treatment had equiaxed grains with evenly distributed binary phase Zn2Zr. The binary Mg2Ca and ternary Mg2Ca6Zn3 phases were identified in the matrix and at grain boundaries surrounded by precipitate-depleted zones (PDZs). The thermal stability of the Zr-modified alloys was examined by microhardness measurements conducted after prolonged exposures of the alloys to elevated temperatures. It was found that Zr is a structure-stabilizing factor. Its influence was associated with the formation of Zn2Zr phase that does not undergo coarsening at the elevated temperatures used (due to the low diffusivity of Zr). The nanoscale mechanical properties of grain boundary PDZs were analyzed using combined nanoindentation and atomic force microscopy. These mechanical properties were then correlated to the composition and precipitate distribution in PDZs. An increase in the solution treatment duration from 10 to 96 h at 410 °C resulted in expansion of PDZs from ~0.75 to ~3 µm, while the following aging at 175 °C for up to 24 h did not lead to a detectable change in PDZs. The analysis indicates that the lowest hardness was found in the region where Zn2Zr precipitates density was low, regardless of the solute concentration.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (13)

Show source-provided references
1. Tamura Y, Kono N, Motegi T, Sato E (1998) J Jpn Inst Light Met 48:18510.2464/jilm.48.185 ↗
2. Hildebrand ZCG, Qian M, StJohn DH, Frost MT (2003) In: Proceedings of the light metals technology conference, Brisbane, p 195
3. Qian Ma, Das A (2006) Scr Mater 54(5):88110.1016/j.scriptamat.2005.11.002 ↗
4. Liu K, Zhang J, Sun W, Qiu X, Lu H, Tang D, Rokhlin LL, Elkin FM, Meng J (2009) J Mater Sci 44(1):74. doi: 10.1007/s10853-008-3122-z10.1007/s10853-008-3122-z ↗
5. Li D, Wang Q, Ding W (2009) J Mater Sci 44(12):3049. doi: 10.1007/s10853-009-3403-110.1007/s10853-009-3403-1 ↗
6. StJohn DH, Qian Ma, Easton MA, Cao P, Hildebrand Z (2005) Metall Mater Trans 36A:166910.1007/s11661-005-0030-6 ↗
7. Shepelev D, Gorny A, Bamberger M, Katsman A (2008) In: Pekguleryuz M (ed) Proceedings of TMS annual meeting and exhibition, Magnesium technology 2008, New Orlean, p 347
8. Tomo O, Shoichi H, Tatsuo S (2006) Keikinzoku 56:644
9. Levi G, Avraham S, Zilberov A, Bamberger M (2006) Acta Mater 54:52310.1016/j.actamat.2005.09.023 ↗
10. Knapp GS, Fradin FY, Culbert HV (1971) J Appl Phys 42:134110.1063/1.1660244 ↗
11. Swanson HE, Fuyat RK (1953) Natl Bur Stand Circ 539:11
12. Cao P, Qian Ma, StJohn DH, Frost MT (2004) Mater Sci Technol 20(5):58510.1179/026708304225012314 ↗
13. Nix WD, Gao HJ (1998) Mech Phys Solids 46:41110.1016/S0022-5096(97)00086-0 ↗