journal article·2008-05

Comparison of failure mechanisms between rubber-modified and unmodified epoxy adhesives under mode II loading condition

Makoto Imanaka, Ryousuke Orita, Yosinobu Nakamura, Masaki Kimoto

Journal of Materials Science· Volume 43· Issue 9
Publisher page

Abstract

The effect of rubber modification on fracture toughness of adhesive joints under mode II loading condition was investigated in comparison with that under mode I loading, wherein the two adhesives rubber-modified and unmodified were used. To evaluate the fracture toughness on the basis of R-curve characteristics under mode II loading condition, four-point bend tests had been conducted for the adhesively bonded end-notched flexure (ENF) specimens. Thus obtained R-curves revealed the following trend: its behavior did not appear for the unmodified adhesive, whereas the rubber-modified adhesive exhibited a typical behavior. In the initial stage of crack propagation, GIIC of the rubber-modified adhesive is lower than that of the unmodified adhesive, but becomes greater in the range of Δa > 25 mm. Nevertheless, the significant improvement of the fracture toughness with the rubber modification under mode I loading condition was not observed under mode II loading. Moreover, FEM analysis was made to elucidate the relation between the above fracture behavior and stress distributions near the crack tip. The results gave the reasonable relationship between evolution of plastic zone and the area with high void-fraction as well as the R-curves behavior. In addition, macroscopic and SEM observations for the fracture surfaces were also conducted.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Mechanical Behavior of Composites · Epoxy Resin Curing Processes · Electronic Packaging and Soldering Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. Bascom WD, Cottington RL, Jones RL, Peyser P (1975) J Appl Polym Sci 19:252410.1002/app.1975.070190917 ↗
2. Bascom WD, Cottington RL (1976) J Adhes 7:33310.1080/00218467608075063 ↗
3. Rakestraw MD, Taylor NW, Dillard AD, Chang T (1995) J Adhes 55:12310.1080/00218469509342411 ↗
4. Daghyani HR, Ye L, Mai Y-W (1995) J Adhes 53:14910.1080/00218469508009935 ↗
5. Daghyani HR, Ye L, Mai Y-W (1996) J Mater Sci 31:2523. doi: https://doi.org/10.1007/BF0068727710.1007/BF00687277 ↗
6. Ashcroft IA, Hughes DJ, Shaw SJ (2001) Int J Adhes Adhes 21:8710.1016/S0143-7496(00)00038-5 ↗
7. Yee AF, Person RA (1988) In: Roulin-Moloney AC (ed) Fracto-graphy and failure mechanism of polymers and composites. Elesvier Applied Science Publisher, London & New York, p 219
8. Chai H (1992) Int J Frac 58:22310.1007/BF00015617 ↗
9. Chai H (1998) Int J Frac 37:13710.1007/BF00041716 ↗
10. Daghyani HR, Ye L, Mai Y-W (1996) J Adhes 56:71
11. Blackman BRK, Kinloch AJ, Paraschi M (2005) Eng Frac Mech 72:87710.1016/j.engfracmech.2004.08.007 ↗
12. Chai H, Martin YMC (1996) J Mech Phys Solids 44:166910.1016/0022-5096(96)00048-8 ↗
13. Kim HS, Ma P (1998) Key Eng Mater 137:17910.4028/www.scientific.net/KEM.137.179 ↗
14. Kim HS, Ma P (1998) J Appl Polym Sci 69:40510.1002/(SICI)1097-4628(19980711)69:2<405::AID-APP22>3.0.CO;2-T ↗
15. Ookubo K, Yoshimitu H, Fujii Y (2001) Trans JSME Ser A 67:106 (in Japanese)10.1299/kikaia.67.1514 ↗
16. de Morais AB, de Moura MFSF (2006) Eng Frac Mech 73:226410.1016/j.engfracmech.2006.05.003 ↗
17. Martin RH, Davidson BD (1999) Plast Rubber Comp 28:40110.1179/146580199101540565 ↗
18. Schuecker C, Davidson BD (2000) ASTM STP 1383:334
19. Sun X, Davidson BD (2005) Int J Frac 135:5110.1007/s10704-005-3746-9 ↗
20. Du J, Thouless MD, Yee AF (2000) Acta Mater 48:358110.1016/S1359-6454(00)00110-5 ↗
21. Person RA, Yee AF (1989) J Mater Sci 24:2571. doi: https://doi.org/10.1007/BF0117452810.1007/BF01174528 ↗
22. Guild FJ, Kinloch AJ (1995) J Mater Sci 30:1689. doi: https://doi.org/10.1007/BF0035159710.1007/BF00351597 ↗
23. Chen XH, Mai Y-W (1998) J Mater Sci 33:3529. doi: https://doi.org/10.1023/A:100468670863910.1023/A:1004686708639 ↗
24. Chen XH, Mai Y-W (1999) J Mater Sci 34:2139. doi: https://doi.org/10.1023/A:100457621337910.1023/A:1004576213379 ↗
25. Gurson AL (1977) J Eng Mater Tech 99:210.1115/1.3443401 ↗
26. Tvergaard V (1982) J Mech Phys Solids 30:39910.1016/0022-5096(82)90025-4 ↗
27. Kody RS, Lesser AJ (1999) Polym Comp 20:25010.1002/pc.10352 ↗
28. Ikeda T, Mano J, Ikemoto D, Lee DB, Miyazaki N (2003) Trans Japan Soc Mech Eng 69:434 (in Japanese)10.1299/kikaia.69.434 ↗
29. Imanaka M, Nakamura Y, Nishimura A, Iida T (2003) Comp Sci Tech 63:4110.1016/S0266-3538(02)00175-6 ↗