Hydrothermal synthesis of mono-dispersed quartz powders
Source abstract
Abstract
The hydrothermal method was first used for crystallization of quartz in the middle of 19th century, and has been developed to grow large single crystals of quartz industrially [1]. On the other hand, the hydrothermal method has been recognized as an excellent method to prepare ceramic powders [2]. Though the large single crystals of quartz are artificially grown due to their application as piezoelectric materials, few studies to get fine powders of quartz have been reported. If a quartz powder with a controlled particle size distribution is prepared, it can be used as a cheap source for abrasives and additives to plastics because quartz has high hardness [3] and the earth’s crust consists of a large amount of silicon [4]. Lee et al. [5] prepared quartz powders (1–10 μm in size) from amorphous silica by adding seed crystals under hydrothermal conditions (240–450 ◦C, 100– 300 atm). Seed crystals might not be necessary, because homogenous nucleation and crystal growth can be expected under hydrothermal conditions due to the difference in solubility of amorphous silica and quartz. They found that KOH was the most effective mineralizer in various alkali hydroxides and alkali halides. Though they showed that quartz crystals were formed at high temperatures over 260 ◦C in 0.5 wt% KOH solution, most of the results shown in their report were obtained at 350 or 400 ◦C. The necessity of high temperatures and KOH solutions are not desirable for industrial preparation. We intended to develop a method to prepare quartz powders with finer particle size under milder hydrothermal conditions using a NaOH solution. In this study, the mono-dispersed fine quartz particles with an average diameter of 0.6 μm were prepared by the hydrothermal reaction in 0.33 M NaOH solutions at 300 ◦C. The starting material was the commercial silica gel (Nipsil-VN3, SiO298.63 wt%, Nippon Silica Industrial Co. Ltd., Japan), which consisted of fine spherical particles with the average diameter of 18 nm. The specific surface area determined by the BET method was 160 m2/g and the amount of absorbed water was 9.1 wt%. It was used without drying for hydrothermal treatments. Hydrothermal treatments were carried out in a Hastelloy C lined autoclave with the inner volume of 20 cm3. The silica gel (0.5–1.5 g) was mixed with a NaOH solution (15 cm3, 0.1–0.5 M) and ultrasonically dispersed for 15 min. The slurry was placed in the autoclave and heated in an air oven at a desired temperature (220–350 ◦C) for various reaction times (0–24 h). The content of the autoclave was agitated during hydrothermal treatments by rotating the autoclave in the oven. The heating rate was about 10 ◦C per minute. After the hydrothermal treatments, the products were washed with water, ultrasonically dispersed in acetone, and then vacuum dried. The crystalline phases of the products were identified by X-ray diffraction (XRD) and their morphology was observed by a scanning electron microscope (SEM). After a few experiments, the standard condition (Silica gel: 1 g, reaction temperature: 300 ◦C, reaction time: 12 h, NaOH concentration: 033 M) was selected and one reaction factor was changed from the condition to estimate its effect. The standard condition gave a quartz powder consisting of mono-dispersed fine particles (Fig. 2b). Fig. 1 shows XRD patterns of the products prepared varying reaction temperature. At 220 ◦C, lowcristobalite was obtained with low-quartz (Fig. 1a). At higher temperatures over 240 ◦C (Fig. 1b and c), the products consisted of single phase low-quartz. SEM photographs of quartz powders prepared at different temperatures are shown in Fig. 2. In all cases, monodispersed quartz particles were obtained. The particle size of the quartz powder obtained at 240 ◦C (Fig. 2a) was in the range from 0.3 to 0.9 μm with an average of 0.6 μm and similar to that obtained at 300 ◦C (Fig. 2b). However, the surface morphology of the particles was different. The particles obtained at 240 ◦C had rough surface, but those obtained at 300 ◦C had rounded shape with smooth surface. When the reaction temperature increased to 350 ◦C (Fig. 2c), the particle size remarkably increased to 1.5 μm. Fig. 3 shows XRD patterns of the products prepared by varying reaction time. The product obtained by cooling down to room temperature just after the temperature of the autoclave reached 300 ◦C, consisted of amorphous silica with a very small amount of lowquartz (Fig. 3a). As the reaction time increased to 0.5 h (Fig. 3b), the broad peak of the amorphous silica disappeared and high crystalline low quartz phase was obtained. The rate of crystallization of amorphous silica to low-quartz was very fast. It is concluded that lowquartz directly nucleated at 300 ◦C and the quartz nuclei grew to larger particles from the amorphous silica. The increase in reaction time did not have a large effect on particle size distribution and morphology. Fig. 4 shows XRD patterns of the products prepared varying NaOH concentration. When the NaOH concentration was lower than 0.1 M (Fig. 4a), low-cristobalite
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Bone Tissue Engineering Materials · Ferroelectric and Piezoelectric Materials · Acoustic Wave Resonator Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (7)
Show source-provided references
1. K. Byrappa and M. Yoshimura, “Handbook of Hydrothermal Technology” (Noyes Publications/William Andrew Publishing, 2001) p. 53.10.1016/B978-081551445-9.50003-9 ↗
2. W. J. Dawson Ceram. Bull. 67 (1988) 1673.
3. Internet Home Page, “Amethyst Galleries' Mineral Gallery” (http://mineral.galleries.com/).
4. B. Mason, “Japanese Translation of Principles of Geochemistry,” 3rd. ed. (John Wiley & Sons, New York, 1966; Iwanami, Tokyo, 1978) p. 49.
5. K. J. Lee, K. W. Seo, H. S. Yu and Y. I. Mok Korean J. Chem. Eng. 13 (1996) 489.10.1007/BF02705999 ↗
6. W. Ostwald Z. Phys. Chem. 34 (1900) 503.
7. A. S. Campbell and W. S. Fyfe Amer. Mineral. 45 (1960) 464.