journal article·2008-09

Combustion synthesis/quasi-isostatic pressing of TiC0.7–NiTi cermets: microstructure and transformation characteristics

E. R. Strutt, T. Radetic, E. A. Olevsky, M. A. Meyers

Journal of Materials Science· Volume 43· Issue 17
Publisher page

Abstract

TiC0.7–NiTi cermets were produced by combustion synthesis followed by quasi-isostatic consolidation while the reaction products were still hot and ductile. The TiC0.7–NiTi cermets were characterized by differential scanning calorimetry, room temperature transmission electron microscopy (TEM), and in-situ TEM (temperature varied during observation). The matrix of the as-synthesized 20NiTi, 40NiTi, and 60NiTi composites contains both R and B19′ martensites at room temperature. No distinct R-phase morphology could be imaged. In the B19′ martensite, [011] Type II twinning, \( (11\bar 1) \) Type I twinning and (001) compound twinning modes were observed as the lattice invariant shear (LIS) of the R-B19′ transformation. The [011] Type II twinning is often reported as the LIS of the B2-B19′ transformation, but this is the first experimental confirmation of its predicted presence as a qualified LIS of the R-B19′ transformation. The (001) compound twinning mode is responsible for the fine structure of the martensite with a wavy morphology. Nanoscale structures with a thickness of 5 nm were obtained inside the twins. Twinning was also observed at the interface with carbide particles, which confirms that some stress relaxation of the elastic mismatch occurs. At room temperature, the matrix of the 80NiTi composite had the R-phase structure, which appeared with a needle-like morphology. Thermal cycling resulted in the suppression of the R-phase transformation. This is the opposite of the behavior observed in un-reinforced NiTi alloys.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Shape Memory Alloy Transformations · Titanium Alloys Microstructure and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Merzhanov AG, Borovinskaya IP (1972) Dokl Akad Nauk SSSR 204:336
2. Gordopolov Y, Merzhanov A (1993) AIAA 154:539
3. Shikhverdiev RM, Yu A (1992) Intl J SHS 1:64
4. Munir ZA, Anselmi-Tamburini U (1989) Mater Sci Rep 3:27710.1016/0920-2307(89)90001-7 ↗
5. Yi HC, Moore JJ (1990) Mater Sci 25:115910.1007/BF00585421 ↗
6. Strutt ER, Olevsky EA, Meyers MA (2008) Paper 1: Combustion synthesis/quasi-isostatic pressing of TiC–NiTi cermets: processing and shrinkage anisotropy (in press)10.1007/s10853-008-2897-2 ↗
7. Goo E, Sinclair R (1985) Acta Metall 33:171710.1016/0001-6160(85)90166-X ↗
8. Hara T, Ohba T, Okunishi E, Otsuka K (1997) Mater Trans JIM 38:1110.2320/matertrans1989.38.11 ↗
9. Hehemann RF, Sandrock GD (1971) Scripta Metall 5:80110.1016/0036-9748(71)90167-0 ↗
10. Otsuka K, Sawamura T, Shimizu K (1971) Phys Status Solida A 5:45710.1002/pssa.2210050220 ↗
11. Jacobs K, Sehitoglu H, Balszer M (1996) Metall Mater Trans A 27A:306610.1007/BF02663855 ↗
12. Miyazaki S, Otsuka K, Wayman CM (1989) Acta Metall 37:1837
13. Hwang CM, Meichle M, Salamon MB, Wayman CM (1983) Philos Mag A 47:910.1080/01418618308243106 ↗
14. Knowles KM, Smith DA (1981) Acta Metall 29:10110.1016/0001-6160(81)90091-2 ↗
15. Onda T, Bando Y, Ohba T, Otsuka K (1992) Mater Trans JIM 33:35410.2320/matertrans1989.33.354 ↗
16. Nishida M, Ohgi H, Itai I, Chiba A, Yamauchi K (1995) Acta Metall Mater 43:121910.1016/0956-7151(94)00332-C ↗
17. Xie Z, Liu Y, Van Humbeeck J (1998) Acta Mater 46:198910.1016/S1359-6454(97)00379-0 ↗
18. Madangopal K, Singh JB (2000) Acta Mater 48:132510.1016/S1359-6454(99)00423-1 ↗
19. Zijlstra SR, Beijer J, Klostermann JA (1974) J Mater Sci 9:14510.1007/BF00554765 ↗
20. Mari D, Dunand DC (1995) Metall Mater Trans A 26A:283310.1007/BF02669642 ↗
21. Stroz D (1997) J Phys IV C5:C5–293
22. Miyazaki S, Igo Y, Otsuka K (1986) Acta Metall 34(10):204510.1016/0001-6160(86)90263-4 ↗
23. Gyobu A, Kawamura Y, Harikawa H, Saburi T (1996) Mater Trans JIM 37:69710.2320/matertrans1989.37.697 ↗
24. Honma T (1987) In: Funakubo H (ed) Shape memory alloys. Gordon and Breach, New York, NY
25. Hanlon JE, Butler SR, Wasilewski RJ (1967) Trans Met Soc AIME 239:1323
26. Todoroki T (1990) In: Duerig TW (ed) Engineering aspects of shape memory alloys, Butterworth and Co., London, p 31510.1016/B978-0-7506-1009-4.50031-7 ↗