Residual toughness of poly(acrylonitrile-butadiene-styrene) (ABS) after fatigue loading—effect of uniaxial fatigue loading
Source abstract
Abstract
Toughness variation of non-notched poly(acrylonitrile-butadiene-styrene) (ABS) subjected to uniaxial fatigue loading was investigated. The experiments were conducted by applying fatigue loading to strip specimens first, from which dog-bone specimens were machined. The dog-bone specimens were tested to measure the strain for the on-set of fracture, named cracking strain here, thus to monitor the toughness change due to the fatigue loading. The test results showed that the fatigue loading caused the toughness drop in ABS, even before any visible crack was developed. Damage development and fracture behavior were then analyzed using scanning electron microscopy (SEM). The SEM analysis revealed that damage zones, not cracks, were initiated during the fatigue loading, and were the main cause of the toughness drop. Mechanisms for the damage initiation include matrix crazing and debonding of small rubber particles; however, large rubber particles remained intact. Based on the results, a deformation model is proposed for the damage zone initiation, which provides an explanation for the toughness change under the fatigue loading.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical Behavior of Composites · Polymer crystallization and properties · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (14)
Show source-provided references
1. J. A. SAUER and C. C. CHEN, Adv. Polym. Sci. 91/92(1990) 69.10.1007/BFb0018019 ↗
2. Idem., ibid . 52/53(1983) 169.10.2307/43628719 ↗
3. P.-Y. B. JAR, K. KONISHI and T. SHINMURA, J. Mater. Sci. 37(2002) 4521.10.1023/A:1020667409050 ↗
4. R. MARISSEN, A. V. J. KEMP, S. M. H. COOLEN, W. G. DUIZINGS, A. VAN DER POL and A. J. VAN GULICK, ibid. 36(2001) 4167.10.1023/A:1017960704248 ↗
5. P.-Y. B. JAR, A. J. BERRY, K. KONISHI and T. SHINMURA, J. Mater. Sci. Lett. 20(2001) 655.10.1023/A:1010985820928 ↗
6. J. P. TROTIGNON, Int'l. Polym. Sci. Tech. 20(2) (1993) T67.
7. H. J. KWON, P.-Y. B. JAR and Z. XIA, in Proceedings of 19th Canadian Congress of Applied Mechanics, Calgary, June 2003, edited by M. Epstein et al.(2003) 128.
8. E. H. ROWE and C. K. RIEW, Soc. Plastic Eng. Annual Tech. Conf. Paper 20(1974) 663.
9. Idem., Plastics Eng. 31(1975) 45.
10. Standard Test Method for Tensile Properties of Plastics, D 638-01, Annual Book of ASTM Standards.
11. S. A. MEGUID, "Engineering Fracture Mechanics" (Elsevier Applied Science, London, 1989) p. 76.
12. C. B. BUCKNALL, "Toughened Plastics" (Applied Science, London, 1977) p. 137.10.1007/978-94-017-5349-4 ↗
13. A. M. DONALD and E. J. KRAMER, J. Mater. Sci. 17(1982) 2351.10.1007/BF00543744 ↗
14. R. P. KAMBOUR and R. W. KOPP, J. Polym. Sci. A-2 7(1969) 183.