journal article·2000-10

Thermal analysis of copper-tin alloys during rapid solidification

J. Mahmoudi, H. Fredriksson

Journal of Materials Science· Volume 35· Issue 19
Publisher page

Abstract

A series of solidification experiments using a mirror furnace and a levitation technique were performed on different Cu-Sn alloys. Cooling curves during solidification were registered using a thermocouple of type K connected to a data acquisition system. The undercooling, cooling rates of the liquid and of the solid state, solidification times and temperatures were evaluated from the curves. The samples were found to solidify far below the liquidus temperature. The cooling curves for different samples and alloys were simulated using a FEM solidification program. The heat transfer coefficient, heat of fusion and specific heat were evaluated. It was found that the calculated values of the heat of fusion were much lower than the tabulated ones. The calculated values of the specific heat in the solid state were also found to be much higher than those quoted in the literature, especially for the mirror furnace experiments. The effect of rapid cooling on the thermodynamic state and the solidification process of the alloys has been evaluated. The effect of cooling rate on the formation and condensation of vacancies is discussed. It is proposed that a large number of vacancies form during rapid solidification and that they condense during and after the solidification. The influence of these defects on the thermodynamics and solidification of the alloys has been evaluated.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Solidification and crystal growth phenomena · Metallurgical and Alloy Processes · Electronic Packaging and Soldering Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. L. A. O'brien and R. M. German, J. Mater. Sci. 23 (1988) 3563.10.1007/BF00540496 ↗
2. P. P. Corso, JR., R. M. German and H. D. Simmons, J. Dent. Res. 64 (1985) 854.10.1177/00220345850640051401 ↗
3. H. S. Kim, K. H. Lee, M. C. Shin, S. Y. Kim and M. H. Dzo, Scripta Materialia (1998) in press.
4. P. P. Corso, JR., R. M. German and H. D. Simmons, JR., J. Dent. Res. 64(5) (1985) 848.10.1177/00220345850640051301 ↗
5. S. Sastri, T. K. Vaidyanathan and K. Mukherjee, Metallurgical Transactions A 13A (1982) 313.10.1007/BF02643322 ↗
6. C. Bessing, M. Bergman and A. Thore'n, Dent Mater. 3 (1987) 153.10.1016/S0109-5641(87)80049-0 ↗
7. P R. Merger, M. M. A. Vrijhoef and E. H. Greener, ibid. 1 (1985) 177.10.1016/S0109-5641(85)80013-0 ↗
8. H. Herø and R. B. Jorgensen, J. Dent. Res. 63(6) (1984) 926.10.1177/00220345840630062401 ↗
9. I. R. Harris, M. Norman and A. W. Bryant, J. the Less-Common Metals. 16 (1968) 427.10.1016/0022-5088(68)90141-0 ↗
10. ASTM, 1980 annual book of ASTM Standards, part 10, G5 (ASTM, Philadelphia, PA, 1980). p. 592.
11. J. R. Knight and D. W. Rhys, J. Less-Common Metals. 1 (1959) 292.10.1016/0022-5088(59)90005-0 ↗
12. D. Ott and CH. J. Raub, Gold Bull. 14 (1981) 69.10.1007/BF03214600 ↗
13. T. Sheehan, “Corrosion testing techniques using potentiostats and galvanostats,” Vol. 10, (1980) p. 18.
14. H. S. Kim and K. H. Lee, Biomaterials Research 1 (1997) 15.
15. R. M. German, D. C. Wright and R. F. Gallant, J. Prosthetic Dentistry 47 (1982) 399.10.1016/S0022-3913(82)80090-5 ↗
16. H. J. Mueller, J. W. Lenke and M. S. Bapna, Scanning Microscopy 2 (1988) 777.
17. D. Fort, R. E. Smallman and I. R. Harris, J. the Less-common Metals 31 (1973) 263.10.1016/0022-5088(73)90163-X ↗
18. M. M. Karnowsky, J. Mater. Sci. 13 (1978) 2339.10.1007/BF00808047 ↗
19. H. HerØ, R. JØrgensen, E. SØrbrØden and E. Suoninen, J. Dent. Res. 61(5) (1982) 673.10.1177/00220345820610051001 ↗
20. M. Syverud and H. HerØ, Acta Odontol Scand 42 (1984) 47.10.3109/00016358409041131 ↗