journal article·2003-02

Correlation of fatigue and creep crack growth in poly(vinyl chloride)

Y. Hu, J. Summers, A. Hiltner, E. Baer

Journal of Materials Science· Volume 38· Issue 4
Publisher page

Abstract

Slow crack growth in PVC pipe was studied in order to develop a methodology for predicting long-term creep fracture from short-term tension-tension fatigue tests. In all cases, the crack propagated continuously through a crack-tip craze. In fatigue, the density of drawn craze fibrils gradually increased with decreased frequency and increased temperature. At the lowest frequency, 0.01 Hz, the fibril density in fatigue approached that in creep. The kinetics of fatigue and creep crack growth followed the conventional Paris law formulations with the same exponent 2.7, da/dt = AfΔKI2.7, da/dt = BKI2.7, respectively. The effects of frequency, temperature and R-ratio (the ratio of minimum to maximum stress intensity factor in the fatigue loading cycle) on the Paris law prefactors were characterized. Comparison of frequency and R-ratio tests revealed that the fatigue contribution depended on strain rate. Therefore, at each temperature, crack growth rate was modeled as the product of a creep contribution that depended only on the maximum stress intensity factor and a fatigue contribution that depended on strain rate: (da/dt) = BKI,max2.7 (1 + Ce), where B is the prefactor in the Paris law for creep and C is a coefficient defining the strain rate sensitivity. A linear correlation allowed extrapolation of the creep prefactor (B) from fatigue data. The extrapolated values were systematically higher than the values measured directly from creep and only converged at Tg. The difference was attributed to damage of the craze fibrils during crack closure upon unloading in the fatigue cycle.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Engineering Applied Research · Fatigue and fracture mechanics · Structural Behavior of Reinforced Concrete

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. K. Gotham and M. Hitch, Pipes & Pipelines International 20 (1975) 10.
2. D. Moore, R. Stephenson and M. Whale, Plastics, Rubber and Composites Processing and Applications 3 (1983) 53.
3. M. Skibo, J. Manson, R. Hertzberg and E. Collins, J. Macromol. Sci.-Phys., B 14(4) (1977) 525.10.1080/00222347708212236 ↗
4. L. Burn, Plastics, Rubber and Composites Processing and Applications 21 (1994) 99.
5. L. Konczol, W. Doll and L. Bevan, Colloid & Polymer Science 268 (1990) 814.10.1007/BF01410959 ↗
6. H. Kim and X. Wang, J. Mater. Sci. 29 (1994) 3209.10.1007/BF00356664 ↗
7. S. Maddox and S. Manteghi, Plastics, Rubber and Composites Processing and Applications 17 (1992) 5.
8. R. Hertzberg and J. Manson, in “Fatigue of Engineering Plastics” (Academic Press, New York, 1980).
9. J. Phillips, R. Hertzberg and J. Manson, in “Fatigue '87,” vol. III (Engineering Materials Advisory Service LTD, West Mildland, UK, 1987) p. 1317.
10. H. Kim, R. Truss, Y. Mai and B. Cotterell, Polymer 29 (1988) 268.10.1016/0032-3861(88)90333-3 ↗
11. J. Mandell and J. Chevaillier, Polym. Engr. Sci. 25 (1985) 170.10.1002/pen.760250305 ↗
12. Y. Mai and P. Keer, J. Vinyl. Technology 7 (1985) 130.10.1002/vnl.730070403 ↗
13. L. Lee, J. Mandell and F. Mcgarry, Polym. Engr. Sci. 26 (1986) 626.10.1002/pen.760260908 ↗
14. C. Rimnac, R. Hertzberg and J. Manson, J. Mater. Sci. 19 (1984) 1116.10.1007/BF01120020 ↗
15. M. Schinker, L. Konczol and W. Doll, J. Mater. Sci. Lett. 1 (1982) 475.10.1007/BF00721933 ↗
16. W. Doll, in “Fractography and Failure Mechanisms,” edited by A. Roulin-Moloney (Applied Science, London, 1989) p. 387.
17. Y. Hu, J. Summers, A. Hiltner and E. Baer, J. Vinyl. and Addit. Technology 8(4) (2002).10.1002/vnl.10371 ↗
18. M. Parsons, E. Stepanov, A. Hiltner and E. Baer, J. Mater. Sci. 34 (1999) 3315.10.1023/A:1004616728535 ↗
19. E. Stepanov, A. Hiltner and E. Baer, J. Mater. Sci. Idem., ibid.} 35 (2000) 1857.10.1023/A:1004741713514 ↗
20. E. Stepanov, A. Hiltner and E. Baer, J. Mater. Sci. Idem., ibid.} 35 (2000) 2659.10.1023/A:1004789522642 ↗
21. E. Stepanov, A. Hiltner and E. Baer, J. Mater. Sci. Idem., ibid.} 36 (2001) 5747.10.1023/A:1012935517866 ↗
22. N. Brown and X. Lu, Polymer 36 (1995) 543.10.1016/0032-3861(95)91563-M ↗
23. P. O'connell, M. Bonner, R. Duckett and I. Ward, ibid. 36 (1995) 2355.10.1016/0032-3861(95)97333-B ↗
24. B. Mukherjee and D. Burns, Exp. Mech. 11 (1971) 433.10.1007/BF02327747 ↗
25. W. Cheng, G. Miller, J. Manson, R. Hertzberg and L. Sperling, J. Mater. Sci. 25 (1990) 1924.10.1007/BF01045744 ↗
26. H. Kim and X. Wang, J. Appl. Polym. Sci. 57 (1995) 811.10.1002/app.1995.070570705 ↗
27. M. Wyzgoski, G. Novak and D. Simon, J. Mater. Sci. 25 (1990) 4501.10.1007/BF00581115 ↗
28. H. Brown, Macromolecules 24 (1991) 2752.10.1021/ma00010a018 ↗
29. C. Plummer and A. Donald, Polymer 32 (1991) 409.10.1016/0032-3861(91)90443-M ↗
30. E. Kramer and L. Berger, in “Advances in Polymer Science: Crazing in Polymers,” 91/92:2, edited by H. Kause (Springer-Verlag, New York, 1990) p. 1.
31. L. Berger and E. Kramer, Macromolecules 20 (1987) 1980.10.1021/ma00174a049 ↗
32. H. Brown, E Kramer and R. Bubeck, J. Polym. Sci.: Part B: Polym. Phys. 25 (1987) 1765.10.1002/polb.1987.090250816 ↗
33. R. Schirrer, J. Mater. Sci. 22 (1987) 2289.10.1007/BF01082106 ↗