journal article·2002-07

Characterization of microstructures and toughening behavior of fiber-containing toughened nylon 6,6

S. C. Wong, G. X. Sui, C. Y. Yue, Y.-W. Mai

Journal of Materials Science· Volume 37· Issue 13
Publisher page

Abstract

The toughening behavior of short glass fiber reinforced toughened polymers was studied using fracture mechanics and microscopic techniques. The essential work of fracture (EWF) analysis shows that the inclusion of short glass fibers not only provided a stiffening effect but also a toughening influence. It was observed that rubber-related toughening and fiber-related toughening were competitive in nature for the reinforced, toughened nylon 6,6. When the matrix stress was substantially reduced by the presence of short fibers via the load-shedding mechanism, rubber toughening was severely curtailed. At higher fiber volume fractions, fiber pull-out work contributed significantly to the enhancement of the specific essential fracture work. Fiber-end plasticity was evident under microscopic examination.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Mechanical Behavior of Composites · Fiber-reinforced polymer composites · Epoxy Resin Curing Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. C. B. BUCKNALL, in “Toughened Plastics” (Applied Science Publishers, London, 1977).10.1007/978-94-017-5349-4 ↗
2. R. A. PEARSON, H. J. SUE and A. F. YEE (eds.), “Toughening of Plastics: Advances in Modeling and Experiments,” ACS Symposium Series 759 (American Chemical Society, Washington D. C., 2000).
3. D. R. PAUL and C. B. BUCKNALL (eds.), “Polymer Blends, Vol. 2: Performance” (Wiley-Interscience, New York, 2000).
4. S. V. NAIR, M. L. SHIAO and P. D. GARRETT, J. Mater. Sci. 27 (1992) 1085.10.1007/BF01197664 ↗
5. T. J. PECORNI and R. W. HERTZBERG, Polym. Comp. 15 (1994) 173.
6. S. C. WONG and Y. W. MAI, Polym. Eng. Sci. 39 (1999) 356.10.1002/pen.11422 ↗
7. D. M. LAURA, H. KESKKULA, J. W. BARLOW and D. R. AUL, Polymer 41 (2000) 7165.10.1016/S0032-3861(00)00049-5 ↗
8. Idem., ibid. 42 (2001) 6161.10.1016/S0032-3861(01)00068-4 ↗
9. J. KARGER-KOCSIS, J. Polym. Eng. 12 (1993) 77.
10. H. ZHANG and L. A. BERGLUND, Polym. Eng. Sci. 33 (1993) 100.10.1002/pen.760330208 ↗
11. D. E. MOUZAKIS, F. STRICKER, M ¨ULHAUPT and J. KARGER-KOCSIS, J. Mater. Sci. 33 (1998) 2551.10.1023/A:1004345017105 ↗
12. J. LEE and A. F. YEE, ibid. 36 (2001) 7.10.1023/A:1004814002344 ↗
13. S. V. NAIR, S.-C. WONG and L. A. GOETTLER, ibid.32 (1997) 5335.10.1023/A:1018618912039 ↗
14. K. FRIEDRICH, Comp. Sci. Technol. 22 (1985) 43.10.1016/0266-3538(85)90090-9 ↗
15. J. KARGER-KOCSIS and K. FRIEDRICH, ibid. 32 (1988) 293.10.1016/0266-3538(88)90067-X ↗
16. S. V. NAIR, A. SUBRAMANIAM and L. A. GOETTLER, J. Mater. Sci. 32 (1997) 5347.10.1023/A:1018670928878 ↗
17. H. J. SUE and A. F. YEE, J. Mater. Sci. 28 (1993) 2975.10.1007/BF00354702 ↗
18. M. T. TAKEMORI and A. F. YEE, in “Impact Fracture of Polymers—Materials Science and Testing Techniques,” edited by K. Takahashi and A. F. Yee (Kyushu University, Fukuoka-shi, Japan, 1992) p. 331.
19. J. S. WU, C. M. CHAN and Y. W. MAI, in “Polymer Blends and Alloys,” edited by G. O. Shonaike and G. P. Simon (Marcel Dekker, New York, 1999) ch. 18, p. 505.
20. A. KELLY and W. R. TYSON, J. Mech. Phys. Solids. 13 (1965) 329.10.1016/0022-5096(65)90035-9 ↗
21. Y. W. MAI and B. COTTERELL, Int. J. Fract. 32 (1986) 105.10.1007/BF00019787 ↗
22. J. S. WU and Y. W. MAI, Polym. Eng. Sci. 36 (1996) 2275.10.1002/pen.10626 ↗
23. M. L. SHIAO, S. V. NAIR, P. D. GARRETT and R. E. POLLARD, Polymer 35 (1994) 306.10.1016/0032-3861(94)90695-5 ↗