Ignition-resistant Mg-Ca-Y-(Al, Zn) alloys prepared by extrusion
Source abstract
Abstract
Abstract This work focuses on novel magnesium alloys for potential use in the aerospace industry and their comprehensive characterisation. There are several criteria alloys must meet for aerospace applications, including adequate mechanical properties, acceptable cost, and high corrosion and flammability resistance. Based on these requirements, three novel magnesium alloys were designed: Mg-4Ca-1Y, Mg-4Ca-1Y-1Zn, and Mg-4Ca-1Y-1Al-1Zn (wt%), which were processed by extrusion. Their microstructure, mechanical properties, corrosion, and ignition resistance were subsequently analysed in detail. Extrusion processing produced an almost fully recrystallised microstructure with an average grain size below 2 µm in all investigated alloys. Mechanical characterisation by uniaxial compression and tensile testing coupled with digital image correlation, revealed high strength, with yield strengths above 270 MPa in both loading modes. The Mg-4Ca-1Y-1Al-1Zn alloy exhibited the highest tensile yield strength of 341 MPa, attributable to its dense secondary phase structure. However, the most favourable combination of strength and ductility was achieved in the Mg-4Ca-1Y-1Zn alloy, which displayed a tensile yield strength of 275 MPa and a high fracture elongation of 12%. Despite the low content of rare-earth elements, which were replaced by more affordable calcium, the alloys reached exceptionally high ignition temperatures (approximately 1100 °C), exceeding those of the expensive, heavily alloyed commercial WE43 alloy.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Hydrogen Storage and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (54)
Show source-provided references
1. “Performance Standard for Seats in Civil Rotorcraft,” 14 8 2015. [Online]. Available: https://www.sae.org/standards/content/as8049c/.
2. Han D, Zhang J, Huang J, Lian Y, He G (2020) A review on ignition mechanisms and characteristics of magnesium alloys. J Magnes Alloys. https://doi.org/10.1016/j.jma.2019.11.01410.1016/j.jma.2019.11.014 ↗
3. Villegas-Armenta LA, Drew RAL, Pekguleryuz MO (2020) The ignition behavior of Mg-Ca binary alloys: the role of heating rate. Oxid Met 93:54510.1007/s11085-020-09970-x ↗
4. Tekumalla S, Gupta M (2017) An insight into ignition factors and mechanisms of magnesium based materials: a review. Mater Des. https://doi.org/10.1016/j.matdes.2016.09.10310.1016/j.matdes.2016.09.103 ↗
5. Czerwinski F (2014) Controlling the ignition and flammability of magnesium for aerospace applications. Corros Sci. https://doi.org/10.1016/j.corsci.2014.04.04710.1016/j.corsci.2014.04.047 ↗
6. Aydin DS, Bayindir Z, Hoseini M, Pekguleryuz MO (2013) The high temperature oxidation and ignition behavior of Mg-Nd alloys part I: the oxidation of dilute alloys. J Alloys Compd. https://doi.org/10.1016/j.jallcom.2013.03.13010.1016/j.jallcom.2013.03.130 ↗
7. Aydin DS, Bayindir Z, Pekguleryuz MO (2014) The high temperature oxidation behavior of Mg-Nd alloys. Part II: the effect of the two-phase microstructure on the on-set of oxidation and on oxide morphology. J Alloys Compd. https://doi.org/10.1016/j.jallcom.2013.09.11010.1016/j.jallcom.2013.09.110 ↗
8. Kim YM, Yim CD, Kim HS, You BS (2011) Key factor influencing the ignition resistance of magnesium alloys at elevated temperatures. Scripta Mater 65(11):95810.1016/j.scriptamat.2011.08.019 ↗
9. Kubásek J, Minárik P, Hosová K, Šašek S, Knapek M, Veselý J, Stráská J, Dvorský D, Čavojský M, Vojtěch D (2021) Novel magnesium alloy containing Y, Gd and Ca with enhanced ignition temperature and mechanical properties for aviation applications. J Alloys Compd 877:16008910.1016/j.jallcom.2021.160089 ↗
10. Šašek S, Minárik P, Hosová SJK, Král VJKJR, Krajňák T, Vojtěch D (2023) Novel ultrafine-grain Mg-Gd/Nd-Y-Ca alloys with an increased ignition temperature. Mater. https://doi.org/10.3390/ma1603129910.3390/ma16031299 ↗
11. Minárik P, Veselý J, Král R, Bohlen J, Kubásek J, Janeček M, Stráská J (2017) Exceptional mechanical properties of ultra-fine grain Mg-4Y-3RE alloy processed by ECAP. Mater Sci Eng: A 708:19310.1016/j.msea.2017.09.106 ↗
12. Li F, Peh WY, Nagarajan V, Ho MK, Danno A, Chua BW, Tan MJ (2016) Development of non-flammable high strength AZ91+Ca alloys via liquid forging and extrusion. Mater Des 99:3710.1016/j.matdes.2016.03.014 ↗
13. Kawamura Y, Flame-resistant Magnesium Alloys with High Strength 2013
14. Ding J, Zhao WM, Qin L, Li YY (2014) Study of Ca and Ce Additions on Different Ignition Resistance Behavior of Magnesium Alloy. Mater Sci Forum 788:710.4028/www.scientific.net/MSF.788.7 ↗
15. Šašek S, Minárik P, Kubásek J, Boukalová A, Dittrich J, Stráská J, Veselý J, Knapek M, Bohlen J, Vojtěch D (2025) Non-flammable Mg-Ca-Y alloys with Al and Zn addition processed by equal channel angular pressing”. J Alloys Compd 1031:18099410.1016/j.jallcom.2025.180994 ↗
16. Zeng ZR, Bian MZ, Xu SW, Davies CHJ, Birbilis N, Nie JF (2016) Effects of dilute additions of Zn and Ca on ductility of magnesium alloy sheet. Mater Sci Eng: A 674:45910.1016/j.msea.2016.07.049 ↗
17. Fekete KH, Drozdenko D, Čapek J, Máthis K, Tolnai D, Stark A, Garcés G, Dobroň P (2020) Hot deformation of Mg-Y-Zn alloy with a low content of the LPSO phase studied by in-situ synchrotron radiation diffraction. J Magnes Alloys. https://doi.org/10.1016/j.jma.2019.11.00910.1016/j.jma.2019.11.009 ↗
18. Boukamp BA (1995) A linear Kronig-Kramers transform test for immittance data validation. J electrochem soc 142:188510.1149/1.2044210 ↗
19. Gupta M, Ling SNM (2011) Magnesium, magnesium alloys, and magnesium. John Wiley & Sons10.1002/9780470905098 ↗
20. King AD, Birbilis N, Scully JR (2014) Accurate electrochemical measurement of magnesium corrosion rates; a combined impedance, mass-loss and hydrogen collection study. Electrochim Acta. https://doi.org/10.1016/j.electacta.2013.12.12410.1016/j.electacta.2013.12.124 ↗
21. Burke EC (1955) Solid solubility of calcium in magnesium. JOM 7:285–28610.1007/BF03377491 ↗
22. Aljarrah M, Medraj M (2008) Thermodynamic modelling of the Mg-Ca, Mg-Sr, Ca-Sr and Mg-Ca-Sr systems using the modified quasichemical model. Calphad. https://doi.org/10.1016/j.calphad.2007.09.00110.1016/j.calphad.2007.09.001 ↗
23. Shi X, Zou J, Liu C, Cheng L, Li D, Zeng X, Ding W (2014) Study on hydrogenation behaviors of a Mg-13Y alloy. Int J Hydrogen Energy. https://doi.org/10.1016/j.ijhydene.2014.03.11510.1016/j.ijhydene.2014.03.115 ↗
24. Hao J, Zhang J, Wang H, Cheng W, Bai Y (2022) Microstructure and mechanical properties of Mg-Zn-Y-Mn magnesium alloys with different Zn/Y atomic ratio. J Mater Res Technol 19:1650–165710.1016/j.jmrt.2022.05.153 ↗
25. Luo S, Tang A, Pan F, Kai S, Wang W (2011) Effect of mole ratio of Y to Zn on phase constituent of Mg-Zn-Zr-Y alloys. Trans Nonferrous Metals Soc China 21:795–80010.1016/S1003-6326(11)60783-8 ↗
26. Schäublin RE, Becker M, Cihova M, Gerstl SSA, Deiana D, Hébert C, Pogatscher S, Uggowitzer PJ, Löffler JF (2022) Precipitation in lean Mg-Zn-Ca alloys”. Acta Mater 239:11822310.1016/j.actamat.2022.118223 ↗
27. Suzuki A, Saddock ND, Jones JW, Pollock TM (2005) Solidification paths and eutectic intermetallic phases in Mg–Al–Ca ternary alloys”. Acta Mater 53:2823–283410.1016/j.actamat.2005.03.001 ↗
28. Murai T, Matsuoka S, Miyamoto S, Oki Y (2003) Effects of extrusion conditions on microstructure and mechanical properties of AZ31B magnesium alloy extrusions. J Mater Process Technol. https://doi.org/10.1016/s0924-0136(02)01106-810.1016/s0924-0136(02)01106-8 ↗
29. Mouhib F, Xie Z, Atila A, Guénolé J, Korte-Kerzel S, Al-Samman T (2024) Exploring solute behavior and texture selection in magnesium alloys at the atomistic level. Acta Mater. https://doi.org/10.1016/j.actamat.2024.11967710.1016/j.actamat.2024.119677 ↗
30. Al-Samman T (2013) Modification of texture and microstructure of magnesium alloy extrusions by particle-stimulated recrystallization. Mater Sci Eng: A 560:561–56610.1016/j.msea.2012.09.102 ↗
31. Minárik P, Hosová K, Šašek S, Kubásek J, Veselý J, Král R, Čavojský M, Stráská J, Vojtěch D (2023) Ignition-resistant Mg-2Y-2Gd-1Ca alloy for aviation applications. J Alloys Compd 948:16968310.1016/j.jallcom.2023.169683 ↗
32. Mayama T, Noda M, Chiba R, Kuroda M (2011) Crystal plasticity analysis of texture development in magnesium alloy during extrusion. Int J Plast. https://doi.org/10.1016/j.ijplas.2011.02.00710.1016/j.ijplas.2011.02.007 ↗
33. Azeem MA, Tewari A, Mishra S, Gollapudi S, Ramamurty U (2010) Development of novel grain morphology during hot extrusion of magnesium AZ21 alloy. Acta Mater. https://doi.org/10.1016/j.actamat.2009.10.05610.1016/j.actamat.2009.10.056 ↗
34. Ion SE, Humphreys FJ, White SH (1982) Dynamic recrystallisation and the development of microstructure during the high temperature deformation of magnesium. Acta Metall 30:1909–191910.1016/0001-6160(82)90031-1 ↗
35. Barrett CD, Imandoust A, Oppedal AL, Inal K, Tschopp MA, El Kadiri H (2017) Effect of grain boundaries on texture formation during dynamic recrystallization of magnesium alloys. Acta Mater 128:270–28310.1016/j.actamat.2017.01.063 ↗
36. Jiang MG, Xu C, Yan H, Lu SH, Nakata T, Lao CS, Chen RS, Kamado S, Han EH (2018) Correlation between dynamic recrystallization and formation of rare earth texture in a Mg-Zn-Gd magnesium alloy during extrusion. Sci Rep. https://doi.org/10.1038/s41598-018-35170-410.1038/s41598-018-35170-4 ↗
37. Zhu J, Chen XH, Wang L, Wang WY, Liu ZK, Liu JX, Hui XD (2017) High strength Mg-Zn-Y alloys reinforced synergistically by Mg12ZnY phase and Mg3Zn3Y2 particle. J Alloys Compd. https://doi.org/10.1016/j.jallcom.2017.02.01210.1016/j.jallcom.2017.02.012 ↗
38. Wang H, Zhang DT, Qiu C, Zhang WW, Chen DL (2023) Microstructure and tensile properties of a low-alloyed magnesium alloy: effect of extrusion temperature. J Mater Sci. https://doi.org/10.1007/s10853-023-08877-710.1007/s10853-023-08877-7 ↗
39. Rosalie JM, Somekawa H, Singh A, Mukai T (2013) Effect of precipitation on strength and ductility in a Mg-Zn-Y alloy. J Alloys Compd. https://doi.org/10.1016/j.jallcom.2012.09.02710.1016/j.jallcom.2012.09.027 ↗
40. Czerwinski F (2012) Oxidation characteristics of magnesium alloys. JOM. https://doi.org/10.1007/s11837-012-0477-z10.1007/s11837-012-0477-z ↗
41. Kawamura Y, Osaki N, Kiguchi T, Vinogradov A, Inoue S (2024) Advanced wrought Mg-4.5 Al-2.5 Ca-0.02 Mn (at%) alloys with exceptional balance of high thermal conductivity, yield strength, ductility, nonflammability, and corrosion resistance. J Alloys Compd. https://doi.org/10.1016/j.jallcom.2023.17329910.1016/j.jallcom.2023.173299 ↗
42. Chu A, Zhao Y, Ud-Din R, Hu H, Zhi Q, Wang Z (2021) Microstructure and properties of Mg-Al-Ca-Mn alloy with high Ca/Al ratio fabricated by hot extrusion. Mater Basel. https://doi.org/10.3390/ma1418523010.3390/ma14185230 ↗
43. Tang Y, Inoue S, Mito M, Masuda T, Higo Y, Tange Y, Ohishi Y, Kawamura Y, Horita Z (2023) Simultaneous enhancement of strength and ductility in nonflammable Mg alloys through dynamic precipitation using severe plastic deformation under high pressure. Mater Sci Eng A. https://doi.org/10.1016/j.msea.2023.14539510.1016/j.msea.2023.145395 ↗
44. Han G, Chen D, Chen G, Huang J (2018) Development of non-flammable high strength extruded Mg-Al-Ca-Mn alloys with high Ca/Al ratio. J Mater Sci Technol. https://doi.org/10.1016/j.jmst.2018.03.01910.1016/j.jmst.2018.03.019 ↗
45. Zhang Y, Wu Y, Peng L, Fu P, Huang F, Ding W (2014) Microstructure evolution and mechanical properties of an ultra-high strength casting Mg–15.6 Gd–1.8 Ag–0.4 Zr alloy. J Alloys Compd 615:703–71110.1016/j.jallcom.2014.07.028 ↗
46. Yeganeh H, Bahmani A, Lotfpour M, Malekan M, Emamy M, Nayebi B, Shin KS (2023) Enhanced oxidation and overheating resistance of the extruded Mg-Zn-Al-Mn magnesium alloy by Calcium addition. J Magnes Alloys 11:1276–129110.1016/j.jma.2023.03.004 ↗
47. Go Y, Jo SM, Park SH, Kim HS, You BS, Kim YM (2018) Microstructure and mechanical properties of non-flammable Mg-8Al-0.3 Zn-0.1 Mn-0.3 Ca-0.2 Y alloy subjected to low-temperature, low-speed extrusion. J Alloys Compd. https://doi.org/10.1016/j.jallcom.2017.12.22910.1016/j.jallcom.2017.12.229 ↗
48. Zhou M, Huang X, Morisada Y, Fujii H, Chino Y (2020) Effects of Ca and Sr additions on microstructure, mechanical properties, and ignition temperature of hot-rolled Mg-Zn alloy. Mater Sci Eng A. https://doi.org/10.1016/j.msea.2019.13847410.1016/j.msea.2019.138474 ↗
49. Zhang X, Zhang BD (2013) Corrosion and electrochemical behavior of Mg-Y alloys in 3.5% NaCl solution. Trans Nonferrous Met Soc China. https://doi.org/10.1016/s1003-6326(13)62587-x10.1016/s1003-6326(13)62587-x ↗
50. Zhang X, Zhang K, Deng X, Hongwei L, Yongjun L, Minglong M, Ning L, Wang Y (2012) Corrosion behavior of Mg-Y alloy in NaCl aqueous solution. Prog Nat Sci: Mater Int 22:169–17410.1016/j.pnsc.2012.03.014 ↗
51. Liu X, Shan D, Song Y, Han EH (2017) Influence of yttrium element on the corrosion behaviors of Mg-Y binary magnesium alloy. J Magnes Alloys. https://doi.org/10.1016/j.jma.2016.12.00210.1016/j.jma.2016.12.002 ↗
52. Cheng C, Le Q, Chen L, Hu W, Wang T, Zhu B, Zhou X (2023) Understanding on corrosion mechanism of oxidized AZW800 alloy in 3.5 wt% NaCl solution. J Magnes Alloys. https://doi.org/10.1016/j.jma.2021.08.01510.1016/j.jma.2021.08.015 ↗
53. Benbouzid AZ, Gomes MP, Costa I, Gharbi O, Pébère N, Rossi JL, Rossi JL, Tran MTT, Tribollet B, Turmine M, Vivier V (2022) A new look on the corrosion mechanism of magnesium: An EIS investigation at different pH. Corros Sci 205:11046310.1016/j.corsci.2022.110463 ↗
54. Pardo A, Feliu S Jr, Merino MC, Arrabal R, Matykina E (2010) Electrochemical estimation of the corrosion rate of magnesium/aluminium alloys. Int J Corros 1:953850