Fracture of the C15 CaAl2 Laves phase at small length scales
Source abstract
Abstract
Abstract The cubic C15 CaAl2 Laves phase is an important brittle intermetallic precipitate in ternary Mg–Al–Ca structural alloys. Although knowledge of the mechanical properties of the co-existing phases is essential for the design of improved alloys, the fracture toughness of the C15 CaAl2 intermetallic has not yet been studied experimentally due to limitations posed by macroscale testing of defect-free specimens. Here, miniaturised testing techniques like micropillar splitting and microcantilever bending methods are used to experimentally determine the fracture toughness of the CaAl2 Laves phase. It is found that the toughness value of ~ 1 MPa·√m obtained from pillar splitting with a sharp cube corner geometry is largely insensitive to sample heat treatment, the ion beam used during fabrication, micropillar diameter, and surface orientation. From correlative nanoindentation and electron channelling contrast imaging supported by electron backscatter diffraction, fracture is observed to take place mostly on {011} planes. Atomistic fracture simulations on a model C15 NbCr2 Laves phase showed that the preference of {011} cleavage planes over the more energetically favourable {111} planes is due to lattice trapping and kinetics controlling fracture planes in complex crystal structures, which may provide insights into the experimental results for CaAl2. Using rectangular microcantilever bending tests where the notch plane was misoriented to the closest possible {112} cleavage plane by ~ 8° and the closest {001}, {011}, and {111} planes by > 20°, a toughness of ~ 2 MPa·√m was determined along with the electron microscopy observation of significant deviations of the crack path, demonstrating that preferential crystallographic cleavage planes determine the toughness in this material. Further investigation using pentagonal microcantilevers with precise alignment of the notch with the cleavage planes revealed similar fracture toughness values for different low-index planes. The results presented here are the first detailed experimental study of fracture toughness of the C15 CaAl2 Laves phase and can be understood in terms of crack plane and crack front-dependent fracture toughness. Graphical Abstract
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Boron and Carbon Nanomaterials Research · Metal and Thin Film Mechanics · Magnesium Alloys: Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (48)
Show source-provided references
1. Stein F, Leineweber A (2021) Laves phases: a review of their functional and structural applications and an improved fundamental understanding of stability and properties. J Mater Sci 56:5321–5427. https://doi.org/10.1007/s10853-020-05509-210.1007/s10853-020-05509-2 ↗
2. Zubair M, Sandlöbes S, Wollenweber MA et al (2019) On the role of Laves phases on the mechanical properties of Mg–Al–Ca alloys. Mater Sci Eng A 756:272–283. https://doi.org/10.1016/j.msea.2019.04.04810.1016/j.msea.2019.04.048 ↗
3. Medghalchi S, Zubair M, Karimi E et al (2023) Determination of the rate dependence of damage formation in metallic-intermetallic Mg–Al–Ca composites at elevated temperature using panoramic image analysis. Adv Eng Mater 25:2300956. https://doi.org/10.1002/adem.20230095610.1002/adem.202300956 ↗
4. Guénolé J, Zubair M, Roy S et al (2021) Exploring the transfer of plasticity across laves phase interfaces in a dual phase magnesium alloy. Mater Des 202:109572. https://doi.org/10.1016/j.matdes.2021.10957210.1016/j.matdes.2021.109572 ↗
5. Jiang Z, Jiang B, Zhang J et al (2016) Effect of Al2Ca intermetallic compound addition on grain refinement of AZ31 magnesium alloy. Trans Nonferrous Met Soc China 26:1284–1293. https://doi.org/10.1016/S1003-6326(16)64229-210.1016/S1003-6326(16)64229-2 ↗
6. Zhu G, Wang L, Wang J et al (2020) Highly deformable Mg–Al–Ca alloy with Al2Ca precipitates. Acta Mater 200:236–245. https://doi.org/10.1016/j.actamat.2020.09.00610.1016/j.actamat.2020.09.006 ↗
7. Luo S, Wang L, Wang J et al (2022) Micro-compression of Al2Ca particles in a Mg–Al–Ca alloy. Materialia 21:101300. https://doi.org/10.1016/j.mtla.2021.10130010.1016/j.mtla.2021.101300 ↗
8. Sandlöbes S, Friák M, Korte-Kerzel S et al (2017) A rare-earth free magnesium alloy with improved intrinsic ductility. Sci Rep 7:10458. https://doi.org/10.1038/s41598-017-10384-010.1038/s41598-017-10384-0 ↗
9. Kumar KS (1996) Laves phase-based materials: microstructure, deformation modes and properties. MRS Proc 460:677–688. https://doi.org/10.1557/PROC-460-67710.1557/PROC-460-677 ↗
10. Korte-Kerzel S (2017) Microcompression of brittle and anisotropic crystals: recent advances and current challenges in studying plasticity in hard materials. MRS Commun 7:109–120. https://doi.org/10.1557/mrc.2017.1510.1557/mrc.2017.15 ↗
11. Voß S, Stein F, Palm M, Raabe D (2010) Synthesis of defect-free single-phase bars of high-melting laves phases through modified cold crucible levitation melting. Mater Sci Eng A 527:7848–7853. https://doi.org/10.1016/j.msea.2010.08.06610.1016/j.msea.2010.08.066 ↗
12. Zehnder C, Czerwinski K, Molodov KD et al (2019) Plastic deformation of single crystalline C14 Mg2Ca Laves phase at room temperature. Mater Sci Eng A 759:754–761. https://doi.org/10.1016/j.msea.2019.05.09210.1016/j.msea.2019.05.092 ↗
13. Freund M, Andre D, Zehnder C et al (2021) Plastic deformation of the CaMg2 C14-Laves phase from 50–250°C. Materialia 20:101237. https://doi.org/10.1016/j.mtla.2021.10123710.1016/j.mtla.2021.101237 ↗
14. Freund M, Andre D, Sun PL et al (2023) Plasticity of the C15-CaAl2 laves phase at room temperature. Mater Des 225:111504. https://doi.org/10.1016/j.matdes.2022.11150410.1016/j.matdes.2022.111504 ↗
15. Luo W, Kirchlechner C, Zavašnik J et al (2020) Crystal structure and composition dependence of mechanical properties of single-crystalline NbCo2 Laves phase. Acta Mater 184:151–163. https://doi.org/10.1016/j.actamat.2019.11.03610.1016/j.actamat.2019.11.036 ↗
16. Luo W, Kirchlechner C, Li J et al (2020) Composition dependence of hardness and elastic modulus of the cubic and hexagonal NbCo2 Laves phase polytypes studied by nanoindentation. J Mater Res 35:185–195. https://doi.org/10.1557/jmr.2019.38410.1557/jmr.2019.384 ↗
17. Luo W, Kirchlechner C, Fang X et al (2018) Influence of composition and crystal structure on the fracture toughness of NbCo2 Laves phase studied by micro-cantilever bending tests. Mater Des 145:116–121. https://doi.org/10.1016/j.matdes.2018.02.04510.1016/j.matdes.2018.02.045 ↗
18. Andre D, Freund M, Rehman U, Delis W, Felten M, Nowak J, Tian C, Zubair M, Tanure L, Abdellaoui L, Springer H, Best JP, Zander D, Dehm G, Sandlöbes-Haut S, Korte-Kerzel S (2022) Metallographic preparation methods for the Mg based system Mg–Al–Ca and its laves phases. Mater Charact 192:112187. https://doi.org/10.1016/j.matchar.2022.11218710.1016/j.matchar.2022.112187 ↗
19. Oliver WC, Pharr GM (1992) An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J Mater Res 7:1564–1583. https://doi.org/10.1557/JMR.1992.156410.1557/JMR.1992.1564 ↗
20. Bieler TR, Alizadeh R, Peña-Ortega M, Llorca J (2019) An analysis of (the lack of) slip transfer between near-cube oriented grains in pure Al. Int J Plast 118:269–290. https://doi.org/10.1016/j.ijplas.2019.02.01410.1016/j.ijplas.2019.02.014 ↗
21. Tian C, Dehm G, Kirchlechner C (2021) Influence of strain rate on the activation of {110}, {112}, {123} slip in ferrite of DP800. Materialia 15:100983. https://doi.org/10.1016/j.mtla.2020.10098310.1016/j.mtla.2020.100983 ↗
22. Hiremath P, Melin S, Bitzek E, Olsson PAT (2022) Effects of interatomic potential on fracture behaviour in single- and bicrystalline tungsten. Comput Mater Sci 207:111283. https://doi.org/10.1016/j.commatsci.2022.11128310.1016/j.commatsci.2022.111283 ↗
23. Jang H-S, Seol D, Lee B-J (2021) Modified embedded-atom method interatomic potentials for Mg–Al–Ca and Mg–Al–Zn ternary systems. J Magnes Alloy 9:317–335. https://doi.org/10.1016/j.jma.2020.09.00610.1016/j.jma.2020.09.006 ↗
24. Xie Z, Chauraud D, Atila A et al (2023) Unveiling the mechanisms of motion of synchro-Shockley dislocations in Laves phases. Phys Rev Mater 7:053605. https://doi.org/10.1103/PhysRevMaterials.7.05360510.1103/PhysRevMaterials.7.053605 ↗
25. Rösch F, Trebin H-R, Gumbsch P (2006) Interatomic potentials and the simulation of fracture: C15 NbCr2. Int J Fract 139:517–526. https://doi.org/10.1007/s10704-006-0065-810.1007/s10704-006-0065-8 ↗
26. Andric P, Curtin WA (2018) Atomistic modeling of fracture. Model Simul Mater Sci Eng 27:013001. https://doi.org/10.1088/1361-651X/aae40c10.1088/1361-651X/aae40c ↗
27. Möller JJ, Bitzek E (2014) Fracture toughness and bond trapping of grain boundary cracks. Acta Mater 73:1–11. https://doi.org/10.1016/j.actamat.2014.03.03510.1016/j.actamat.2014.03.035 ↗
28. Liebowitz H, Sih GC (1968) Mathematical theories of brittle fracture. Fracture 2:67–190
29. Guénolé J, Nöhring WG, Vaid A et al (2020) Assessment and optimization of the fast inertial relaxation engine (fire) for energy minimization in atomistic simulations and its implementation in LAMMPS. Comput Mater Sci 175:109584. https://doi.org/10.1016/j.commatsci.2020.10958410.1016/j.commatsci.2020.109584 ↗
30. Thompson AP, Aktulga HM, Berger R et al (2022) LAMMPS—a flexible simulation tool for particle-based materials modeling at the atomic, meso, and continuum scales. Comput Phys Commun 271:108171. https://doi.org/10.1016/j.cpc.2021.10817110.1016/j.cpc.2021.108171 ↗
31. Stukowski A (2009) Visualization and analysis of atomistic simulation data with OVITO–the Open Visualization Tool. Modell Simul Mater Sci Eng 18:015012. https://doi.org/10.1088/0965-0393/18/1/01501210.1088/0965-0393/18/1/015012 ↗
32. CaAl2 Crystal Structure: Datasheet from “PAULING FILE Multinaries Edition—2012” in Springer Materials (https://materials.springer.com/isp/crystallographic/docs/sd_0260702)
33. Sebastiani M, Johanns KE, Herbert EG et al (2015) A novel pillar indentation splitting test for measuring fracture toughness of thin ceramic coatings. Philos Mag 95:1928–1944. https://doi.org/10.1080/14786435.2014.91311010.1080/14786435.2014.913110 ↗
34. Ghidelli M, Sebastiani M, Johanns KE, Pharr GM (2017) Effects of indenter angle on micro-scale fracture toughness measurement by pillar splitting. J Am Ceram Soc 100:5731–5738. https://doi.org/10.1111/jace.1509310.1111/jace.15093 ↗
35. Lauener CM, Petho L, Chen M et al (2018) Fracture of Silicon: influence of rate, positioning accuracy, FIB machining, and elevated temperatures on toughness measured by pillar indentation splitting. Mater Des 142:340–349. https://doi.org/10.1016/j.matdes.2018.01.01510.1016/j.matdes.2018.01.015 ↗
36. Liu CT, Zhu JH, Brady MP et al (2000) Physical metallurgy and mechanical properties of transition-metal Laves phase alloys. Intermetallics 8:1119–1129. https://doi.org/10.1016/S0966-9795(00)00109-610.1016/S0966-9795(00)00109-6 ↗
37. Zhu JH, Pike LM, Liu CT, Liaw PK (1999) Point defects in binary laves phase alloys. Acta Mater 47:2003–2018. https://doi.org/10.1016/S1359-6454(99)00090-710.1016/S1359-6454(99)00090-7 ↗
38. Li C, Wang B, Li Y, Wang R (2009) First-principles study of the ideal cleavage fracture of Cr2Nb microalloyed by X (Al, Ni Co, Ti). Intermetallics 17:394–399. https://doi.org/10.1016/j.intermet.2008.11.01210.1016/j.intermet.2008.11.012 ↗
39. Johnson KL (1987) Contact mechanics. Cambridge University Press
40. Kanninen MF, Popelar CA, Saunders H (1988) Advanced fracture mechanics. J Vib Acoust Stress Reliab Des 110:419–420. https://doi.org/10.1115/1.326954010.1115/1.3269540 ↗
41. Matoy K, Schönherr H, Detzel T et al (2009) A comparative micro-cantilever study of the mechanical behavior of silicon based passivation films. Thin Solid Films 518:247–256. https://doi.org/10.1016/j.tsf.2009.07.14310.1016/j.tsf.2009.07.143 ↗
42. Chan H, Roberts SG, Gong J (2016) Micro-scale fracture experiments on zirconium hydrides and phase boundaries. J Nucl Mater 475:105–112. https://doi.org/10.1016/j.jnucmat.2016.03.02610.1016/j.jnucmat.2016.03.026 ↗
43. Lubliner J, Papadopoulos P (2014) Introduction to solid mechanics: an integrated approach. Springer, New York10.1007/978-1-4614-6768-7 ↗
44. Ohta T, Nakagawa Y, Kaneno Y et al (2003) Microstructures and mechanical properties of NbCr2 and ZrCr2 Laves phase alloys prepared by powder metallurgy. J Mater Sci 38:657–665. https://doi.org/10.1023/A:102180751972810.1023/A:1021807519728 ↗
45. Pérez R, Gumbsch P (2000) Directional anisotropy in the cleavage fracture of silicon. Phys Rev Lett 84:5347–5350. https://doi.org/10.1103/PhysRevLett.84.534710.1103/PhysRevLett.84.5347 ↗
46. Riedle J, Gumbsch P, Fischmeister HF (1996) Cleavage anisotropy in tungsten single crystals. Phys Rev Lett 76:3594–3597. https://doi.org/10.1103/PhysRevLett.76.359410.1103/PhysRevLett.76.3594 ↗
47. Ortiz-Membrado L, Cuadrado N, Casellas D et al (2021) Measuring the fracture toughness of single WC grains of cemented carbides by means of microcantilever bending and micropillar splitting. Int J Refract Metal Hard Mater 98:105529. https://doi.org/10.1016/j.ijrmhm.2021.10552910.1016/j.ijrmhm.2021.105529 ↗
48. Jaya BN, Kirchlechner C, Dehm G (2015) Can microscale fracture tests provide reliable fracture toughness values? A case study in silicon. J Mater Res 30:686–698. https://doi.org/10.1557/jmr.2015.210.1557/jmr.2015.2 ↗