journal article·2023-09

Bendability and ductility enhancement of 7A36 alloys through adding Sc and applying LFEC with a rapid solid solution heating rate treatment

Lingfei Yang, Fang Yu, Chengcheng Chen, Yajun Xu, Zhaoxi Song, Jianzhong Cui, Xiangjie Wang

Journal of Materials Science· Volume 58· Issue 34
Publisher page

Abstract

The present study conducted a detailed investigation to determine the effects of adding Sc and applying low-frequency electromagnetic casting (LFEC) on the bendability and ductility of hot-rolled 7A36 alloy using optical microscopy, electron backscatter diffraction, and scanning electron microscopy by two different solid solution heating rate treatments. Results showed that the rapidly solid-solution-heated rates specimen (R specimen) exhibited several micro-cracks, while the slow solid-solution-heated rates specimen (S specimen) displayed visible cracks and even fractures. Additionally, increasing the solid solution heating rate resulted in a decreased diameter of the second phase but larger average grain size. The coarse second-phase grains of the alloys most likely lead to the formation of microcracks; however, the coarse recrystallized grains prevent the further propagation of bending cracks. The strap-like and finer recrystallized grains of the R specimen lead to an improved bendability of the 7A36 alloy by coordinating plastic deformation and accommodating more dislocations. Further, adding Sc improves the bendability and tensile properties by refining grain size and improves the texture strength, while applying LFEC slightly increases the average grain size and the recrystallizing degree, which result in a high Schmid factor value and lower texture strength, and dislocation density benefits the bendability and ductility of the 7A36 alloy with a little strength reduction.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Advanced Welding Techniques Analysis · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (65)

Show source-provided references
1. Hou YF, Liu CY, Zhang B, Wei LL, Dai HT, Ma ZY (2020) Mechanical properties and corrosion resistance of the fine grain structure of Al–Zn–Mg–Sc alloys fabricated by friction stir processing and post-heat treatment. Mater Sci Eng A 785:139393. https://doi.org/10.1016/j.msea.2020.13939310.1016/j.msea.2020.139393 ↗
2. Lin HQ, Wu YL, Liu SD (2018) Impact of initial temper of base metal on microstructure and mechanical properties of friction stir welded AA 7055 alloy. Mater Charact 146:159–168. https://doi.org/10.1016/j.matchar.2018.09.04310.1016/j.matchar.2018.09.043 ↗
3. Ditta A, Wei LJ, Xu YJ, Wu SJ (2019) Effect of hot extrusion and optimal solution treatment on microstructure and properties of spray-formed Al-11.3Zn-2.65Mg-1Cu alloy. J Alloy Compd 797:558–565. https://doi.org/10.1016/j.jallcom.2019.05.05710.1016/j.jallcom.2019.05.057 ↗
4. Starink MJ, Milkereit B, Zhang Y, Rometsch PA (2015) Predicting the quench sensitivity of Al–Zn–Mg–Cu alloys: a model for linear cooling and strengthening. Mater Des 88:958–971. https://doi.org/10.1016/j.matdes.2015.09.05810.1016/j.matdes.2015.09.058 ↗
5. Azarniya A, Taheri AK, Taheri KK (2019) Recent advances in ageing of 7xxx series aluminum alloys: a physical metallurgy perspective. J Alloy Compd 781:945–983. https://doi.org/10.1016/j.jallcom.2018.11.28610.1016/j.jallcom.2018.11.286 ↗
6. Wang ZP, Pu QQ, Li YG, Xia PK, Gen JW, Li XF, Wang ML, Chen D, Wang HW (2023) Microstructures and mechanical properties of Al-Zn-Mg-Cu alloy with the combined addition of Ti and Zr. J Mater Res Technol 22:747–761. https://doi.org/10.1016/j.jmrt.2022.11.10610.1016/j.jmrt.2022.11.106 ↗
7. Zuo JR, Hou LG, Shi JT, Cui H, Zhuang LZ, Zhang JS (2017) The mechanism of grain refinement and plasticity enhancement by an improved thermomechanical treatment of 7055 Al alloy. Mater Sci Eng A 702:42–52. https://doi.org/10.1016/j.msea.2017.06.10610.1016/j.msea.2017.06.106 ↗
8. Marlaud T, Deschamps A, Bley F, Lefebvre W, Baroux B (2010) Influence of alloy composition and heat treatment on precipitate composition in Al–Zn–Mg–Cu alloys. Acta Mater 58:248–260. https://doi.org/10.1016/j.actamat.2009.09.00310.1016/j.actamat.2009.09.003 ↗
9. Xu YT, Zhang ZF, Gao ZH, Bai YL, Zhao P, Mao WM (2021) Effect of main elements (Zn, Mg and Cu) on the microstructure, castability and mechanical properties of 7xxx series aluminum alloys with Zr and Sc. Mater Charact 182:111559. https://doi.org/10.1016/j.matchar.2021.11155910.1016/j.matchar.2021.111559 ↗
10. Zou Y, Wu XD, Tang SB, Zhu QQ, Song H, Guo MX, Cao LF (2021) Investigation on microstructure and mechanical properties of Al–Zn–Mg–Cu alloys with various Zn/Mg ratios. J Mater Sci Technol 85:106–117. https://doi.org/10.1016/j.jmst.2020.12.04510.1016/j.jmst.2020.12.045 ↗
11. Wei SL, Wang RC, Zhang H, Xu CT, Wu Y, Feng Y (2021) Influence of Cu/Mg ratio on microstructure and mechanical properties of Al–Zn–Mg–Cu alloys. J Mater Sci 56:3472–3487. https://doi.org/10.1007/s10853-020-05438-010.1007/s10853-020-05438-0 ↗
12. Zhao YH, Liao XZ, Jin Z, Valiev RZ, Zhu YT (2004) Microstructures and mechanical properties of ultrafine grained 7075 Al alloy processed by ECAP and their evolutions during annealing. Acta Mater 52:4589–4599. https://doi.org/10.1016/j.actamat.2004.06.01710.1016/j.actamat.2004.06.017 ↗
13. Mo TQ, Chen ZJ, Zhou DY, Lu GM, Huang YM, Liu Q (2022) Effect of lamellar structural parameters on the bending fracture behavior of AA1100/AA7075 laminated metal composites. J Mater Sci Technol 99:28–38. https://doi.org/10.1016/j.jmst.2021.04.07510.1016/j.jmst.2021.04.075 ↗
14. Guo C, Zhang HT, Li SS, Chen RX, Nan YF, Li L, Wang P, Li BM, Cui JZ, Nagaumi H (2021) Evolution of microstructure, mechanical properties and corrosion behavior of Al–4Mg–2Zn–0.3Ag (wt%) alloy processed by T6 or thermomechanical treatment. Corros Sci 188:109551. https://doi.org/10.1016/j.corsci.2021.10955110.1016/j.corsci.2021.109551 ↗
15. Li L, Zhu QF, Zuo YB, Cui JZ (2020) Study on the transitional structures of 7075 aluminum alloy ingot after switching off a low-frequency electromagnetic field in the horizontal direct chill casting. J Cryst Growth 548:125827. https://doi.org/10.1016/j.jcrysgro.2020.12582710.1016/j.jcrysgro.2020.125827 ↗
16. Zuo YB, Cui JZ, Zhao ZH, Zhang HT, Qin K (2005) Effect of low frequency electromagnetic field on casting crack during DC casting superhigh strength aluminum alloy ingots. Mater Sci Eng A 406:286–292. https://doi.org/10.1016/j.msea.2005.07.00110.1016/j.msea.2005.07.001 ↗
17. Muderrisoglu A, Murata M, Ahmetoglu MA, Kinzel G, Altan TL (1996) Bending, flanging, and hemming of aluminum sheet-an experimental study. J Mater Process Technol 59:10–17. https://doi.org/10.1016/0924-0136(96)02281-910.1016/0924-0136(96)02281-9 ↗
18. Xu CC, He H, Yu WY, Li LX (2019) Influence of quenching temperature on peak aging time and hardness of Al–Mg–Si–Cu alloys strengthened by nano-sized precipitates. Mater Sci Eng A 744:28–35. https://doi.org/10.1016/j.msea.2018.11.14910.1016/j.msea.2018.11.149 ↗
19. Bettaieb MB, Lemoine X, Bouaziz O, Habraken AM, Duchêne L (2011) A finite element analysis of the bending and the bendability of metallic sheets. Int J Mater Form 4:283–297. https://doi.org/10.1007/s12289-010-0993-810.1007/s12289-010-0993-8 ↗
20. Poole WJ, Militzer M, Wells MA (2003) Modelling recovery and recrystallisation during annealing of AA 5754 aluminium alloy. Mater Sci Technol 19:1361–1368. https://doi.org/10.1179/02670830322500598010.1179/026708303225005980 ↗
21. Ferry M, Jones D (1997) High-rate annealing of single-phase and particle-containing aluminium alloys. Scr Mater 38:177–183. https://doi.org/10.1016/S1359-6462(97)00498-310.1016/S1359-6462(97)00498-3 ↗
22. Moghanaki SK, Kazeminezhad M, Logé R (2017) Heating rate effect on particle stimulated nucleation and grains structure during non-isothermal annealing of multi-directionally forged solution treated AA2024. Mater Charact 127:317–324. https://doi.org/10.1016/j.matchar.2017.03.02510.1016/j.matchar.2017.03.025 ↗
23. Shen F, Wang B, Yi D, Liu H, Tang C, Shou W (2016) Effects of heating rate during solid-solution treatment on microstructure and fatigue properties of sheet. Mater Des 104:116–125. https://doi.org/10.1016/j.matdes.2016.05.00210.1016/j.matdes.2016.05.002 ↗
24. Lu G, Wang JJ, Liu YJ, Liu CM (2020) Effect of heating rate during solution treatment on the bendability of Al–Mg–Si alloys. Mater Sci Eng A 791:139604. https://doi.org/10.1016/j.msea.2020.13960410.1016/j.msea.2020.139604 ↗
25. Liu WC, Li Z, Man CS (2008) Effect of heating rate on the microstructure and texture of continuous cast AA 3105 aluminum alloy. Mater Sci Eng A 478:173–180. https://doi.org/10.1016/j.msea.2020.13960410.1016/j.msea.2020.139604 ↗
26. Wang XF, Guo MX, Cao LY, Luo JR, Zhang JS, Zhuang LZ (2015) Effect of heating rate on mechanical property, microstructure and texture evolution of Al–Mg–Si–Cu alloy during solution treatment. Mater Sci Eng A 621:8–17. https://doi.org/10.1016/j.msea.2014.10.04510.1016/j.msea.2014.10.045 ↗
27. Yang LF, Chen CK, Yu F, Chen CC, Liu JP, Wang Z, Wang XJ, Cui JZ (2023) Coordinated deformation and high formability mechanisms of 7A36 aluminum alloy by Sc micro-alloying and low-frequency electromagnetic casting. J Mater Res Technol 24:5186–5201. https://doi.org/10.1016/j.jmrt.2023.04.15410.1016/j.jmrt.2023.04.154 ↗
28. Barnwal VK, Raghavan R, Tewari A, Narasimhan K, Mishra SK (2017) Effect of microstructure and texture on forming behaviour of AA-6061 aluminium alloy sheet. Mater Sci Eng A 679:56–65. https://doi.org/10.1016/j.msea.2016.10.02710.1016/j.msea.2016.10.027 ↗
29. Rakshit R, Sarkar A, Panda SK, Mandal S (2022) Influence of out-of-plane stretch forming induced different strain paths on micro-texture evolution, slip system activity and Taylor factor distribution in Al–Li alloy. Mater Sci Eng A 830:142267. https://doi.org/10.1016/j.msea.2021.14226710.1016/j.msea.2021.142267 ↗
30. Babu KA, Athreya CN, Mozumder YH, Sarma VS, Mandal S (2020) A comprehensive study on texture development and twin-related domain evolution following hot compression in a super austenitic stainless steel. Metall Mater Trans A 51:3535–3551. https://doi.org/10.1007/s11661-020-05763-810.1007/s11661-020-05763-8 ↗
31. Abdelhak A, Nathalie A-B, Nadjet R, Francis W (2012) Grain Orientation Spread values in IF steels after plastic deformation and recrystallization. Mater Sci Forum 702:269–272. https://doi.org/10.4028/www.scientific.net/MSF.702-703.26910.4028/www.scientific.net/MSF.702-703.269 ↗
32. Li ZX, Chen JS, Wang XN, Shen XJ, Cen YM, Chen J, Chu YJ, Han YJ (2022) Microstructure distribution and bending fracture mechanism of 65Mn steel in the laser surface treatment. Mater Sci Eng A 850:143568. https://doi.org/10.1016/j.msea.2022.14356810.1016/j.msea.2022.143568 ↗
33. Wang XY, Shen B, Deng L, Li JJ (2017) Effects of original orientation combination on substructure characteristics during continuous dynamic recrystallization in an extruded alloy. Mater Charact 130:113–122. https://doi.org/10.1016/S1359-6462(02)00335-410.1016/S1359-6462(02)00335-4 ↗
34. Birosca S, Liu G, Ding RG, Jiang J, Simm T, Deen C, Whittaker M (2019) The dislocation behaviour and GND development in a nickel based superalloy during creep. Int J Plasti 118:252–268. https://doi.org/10.1016/j.ijplas.2019.02.01510.1016/j.ijplas.2019.02.015 ↗
35. Hua L, Hu X, Han XH (2020) Microstructure evolution of annealed 7075 aluminum alloy and its influence on room-temperature plasticity. Mater Des 196:109192. https://doi.org/10.1016/j.matdes.2020.10919210.1016/j.matdes.2020.109192 ↗
36. Sathiaraj GD, Tsai CW, Yeh JW, Jahazi M, Bhattacharjee PP (2016) The effect of heating rate on microstructure and texture formation during annealing of heavily cold-rolled equiatomic CoCrFeMnNi high entropy alloy. J Alloy Compd 688:752–761. https://doi.org/10.1016/j.jallcom.2016.07.15510.1016/j.jallcom.2016.07.155 ↗
37. Chrominski W, Lewandowska M (2018) Mechanisms of plastic deformation in ultrafine-grained aluminium—in situ and ex-post studies. Mater Sci Eng A 715:320–331. https://doi.org/10.1016/j.msea.2017.12.08310.1016/j.msea.2017.12.083 ↗
38. Briffod F, Bleuset A, Shiraiwa T, Enoki M (2019) Effect of crystallographic orientation and geometrical compatibility on fatigue crack initiation and propagation in rolled Ti–6Al–4V alloy. Acta Mater 177:56–67. https://doi.org/10.1016/j.actamat.2019.07.02510.1016/j.actamat.2019.07.025 ↗
39. Kaithwas CK, Bhuyan P, Pradhan SK, Mandal S (2020) ‘Hall-Petch’ type of relationship between the extent of intergranular corrosion and grain size in a Ni-based superalloy. Corros Sci 175:108868. https://doi.org/10.1016/j.corsci.2020.10886810.1016/j.corsci.2020.108868 ↗
40. Lin YC, Dong W-Y, Zhu X-H, Wu Q, He Y-J (2020) Deformation behavior and precipitation features in a stretched Al–Cu alloy at intermediate temperatures. Materials 13:2495. https://doi.org/10.3390/ma1311249510.3390/ma13112495 ↗
41. Pradhan SK, Bhuyan P, Mandal S (2019) Influence of the individual microstructural features on pitting corrosion in type 304 austenitic stainless steel. Corros Sci 158:108091. https://doi.org/10.1016/j.corsci.2019.10809110.1016/j.corsci.2019.108091 ↗
42. Kubin LP, Mortensen A (2003) Geometrically necessary dislocations and strain-gradient plasticity: a few critical issues. Scr Mater 48:119–125. https://doi.org/10.1016/S1359-6462(02)00335-410.1016/S1359-6462(02)00335-4 ↗
43. Lezaack MB, Hannard F, Simar A (2022) Understanding the ductility versus toughness and bendability decoupling of large elongated and fine grained Al 7475–T6 alloy. Mater Sci Eng A 839:142816. https://doi.org/10.1016/j.msea.2022.14281610.1016/j.msea.2022.142816 ↗
44. Vratnica M, Pluvinage G, Jodin P, Cvijović Z, Rakin M, Burzić Z, Gerić K (2013) Notch fracture toughness of high-strength Al alloys. Mater Des 44:303–310. https://doi.org/10.1016/j.matdes.2012.07.03110.1016/j.matdes.2012.07.031 ↗
45. Ludtka GM, Laughlin DE (1982) The influence of microstructure and strength on the fracture mode and toughness of 7XXX series aluminum alloys. Metall Trans A 13:411–425. https://doi.org/10.1007/BF0264335010.1007/BF02643350 ↗
46. Huskins EL, Cao B, Ramesh KT (2010) Strengthening mechanisms in an Al-Mg alloy. Mater Sci Eng A 527:1292–1298. https://doi.org/10.1016/j.msea.2009.11.05610.1016/j.msea.2009.11.056 ↗
47. Malopheyev S, Kulitskiy V, Kaibyshev R (2017) Deformation structures and strengthening mechanisms in an AlMgScZr alloy. J Alloy Compd 698:957–966. https://doi.org/10.1016/j.jallcom.2016.12.28910.1016/j.jallcom.2016.12.289 ↗
48. Kendig KL, Miracle DB (2002) Strengthening mechanisms of an Al–Mg–Sc–Zr alloy. Acta Mater 50:4165–4175. https://doi.org/10.1016/S1359-6454(02)00258-610.1016/S1359-6454(02)00258-6 ↗
49. Li DX, Zhao K, Liu GL, Han MX, Liu SD, Liu XF (2023) Revealing the correlation of microstructure configuration and mechanical properties of Al–Si–Mg alloy reinforced by C-doped TiB2 and SiC. Mater Des 226:111694. https://doi.org/10.1016/j.matdes.2023.11169410.1016/j.matdes.2023.111694 ↗
50. Huang K, Marthinsen K, Zhao QL, Logé RE (2018) The double-edge effect of second-phase particles on the recrystallization behaviour and associated mechanical properties of metallic materials. Prog Mater Sci 92:284–359. https://doi.org/10.1016/j.pmatsci.2017.10.00410.1016/j.pmatsci.2017.10.004 ↗
51. Robson JD, Henry DT, Davis B (2009) Particle effects on recrystallization in magnesium–manganese alloys: particle-stimulated nucleation. Acta Mater 57:2739–2747. https://doi.org/10.1016/j.actamat.2009.02.03210.1016/j.actamat.2009.02.032 ↗
52. Huang K, Logé RE (2016) A review of dynamic recrystallization phenomena in metallic materials. Mater Des 111:548–574. https://doi.org/10.1016/j.matdes.2016.09.01210.1016/j.matdes.2016.09.012 ↗
53. Hansen N (2004) Hall-Petch relation and boundary strengthening. Scr Mater 61:801–806. https://doi.org/10.1016/j.scriptamat.2004.06.00210.1016/j.scriptamat.2004.06.002 ↗
54. Hansen N (1977) The effect of grain size and strain on the tensile flow stress of aluminium at room temperature. Acta Metall 25:863–869. https://doi.org/10.1016/0001-6160(77)90171-710.1016/0001-6160(77)90171-7 ↗
55. Iadicola MA, Hu L, Rollett AD, Foecke T (2012) Crystal plasticity analysis of constitutive behavior of 5754 aluminum sheet deformed along bi-linear strain paths. Int J Solids Struct 49:3507–3516. https://doi.org/10.1016/j.ijsolstr.2012.03.01510.1016/j.ijsolstr.2012.03.015 ↗
56. Ng KS, Ngan AHW (2008) Breakdown of Schmid’s law in micropillars. Scr Mater 59:796–799. https://doi.org/10.1016/j.scriptamat.2008.06.01910.1016/j.scriptamat.2008.06.019 ↗
57. Li DX, Hu KQ, Han MX, Xie KW, Liu GL, Liu XF (2021) Strength adjust mechanism of high toughness Al4C3/Al–xMg composites. Mater Sci Eng A 824:141842. https://doi.org/10.1016/j.msea.2021.14184210.1016/j.msea.2021.141842 ↗
58. Gurao NP, Sethuraman S, Suwas S (2011) Effect of strain path change on the evolution of texture and microstructure during rolling of copper and nickel. Mater Sci Eng A 528:7739–7750. https://doi.org/10.1016/j.msea.2011.06.06210.1016/j.msea.2011.06.062 ↗
59. Mecking H, Kocks UF, Hartig C (1996) Taylor factors in materials with many deformation modes. Scr Mater 35:465–471. https://doi.org/10.1016/1359-6462(96)00137-610.1016/1359-6462(96)00137-6 ↗
60. Hu XH, Wilkinson DS, Jain M, Wu PD, Mishra RK (2011) The impact of particle distributions and grain-level inhomogeneities on post-necking deformation and fracture in AA5754 sheet alloys during uniaxial tension. Mater Sci Eng A 58:2002–2016. https://doi.org/10.1016/j.msea.2010.11.05110.1016/j.msea.2010.11.051 ↗
61. Azar AS, Svensson L-E, Nyhus B (2015) Effect of crystal orientation and texture on fatigue crack evolution in high strength steel welds. Int J Fatigue 77:95–104. https://doi.org/10.1016/j.ijfatigue.2015.03.00810.1016/j.ijfatigue.2015.03.008 ↗
62. Gupta A, Khatirkar RK, Kumar A, Thool KS, Bhibhanshu N, Suwas S (2021) Texture development during cold rolling of a β-Ti alloy: experiments and simulations. Metall Mater Trans A 52:1031–1043. https://doi.org/10.1007/s11661-020-06117-010.1007/s11661-020-06117-0 ↗
63. Zhang K, Holmedal B, Mánik T, Saai A (2019) Assessment of advanced Taylor models, the Taylor factor and yield-surface exponent for FCC metals. Int J Plast 114:144–160. https://doi.org/10.1016/j.ijplas.2018.10.01510.1016/j.ijplas.2018.10.015 ↗
64. Lu D, Lin B, Liu T, Deng S, Guo Y, Li J, Liu D (2023) Effect of grain structure on fatigue crack propagation behavior of Al–Cu–Li alloys. J Mater Sci Technol 148:75–89. https://doi.org/10.1016/j.jmst.2022.10.08510.1016/j.jmst.2022.10.085 ↗
65. Peng ZW, Li JF, Sang FJ, Chen YL, Zhang XH, Zheng ZQ, Pan QL (2018) Structures and tensile properties of Sc-containing 1445 Al–Li alloy sheet. J Alloy Compd 747:471–483. https://doi.org/10.1016/j.jallcom.2018.03.03210.1016/j.jallcom.2018.03.032 ↗