journal article·2019-11

Effect of service exposure on KCl corrosion attack of AISI 347H FG steel

Yohanes Chekol Malede, Kristian Vinter Dahl, Melanie Montgomery, Flemming Bjerg Grumsen, John Hald

Journal of Materials Science· Volume 54· Issue 21
Publisher page

Abstract

The effect of ageing of AISI 347H FG austenitic steel on KCl-induced corrosion was investigated by comparing the corrosion attack on tube material previously service-exposed for 100000 h and that on an as-received tube. Cr-rich σ-phase precipitates were found mainly along grain boundaries in the microstructure of the service-exposed material, whereas no σ-phase was present in the as-received condition. Laboratory corrosion experiments were carried out using KCl-free and KCl-covered samples in a 15% (v/v) H2O (g) + 5% (v/v) O2 (g) + N2 (g) (balance) atmosphere at 600 °C for 168 h. Microstructural characterisation was performed before and after the corrosion experiments using light optical microscopy, X-ray diffraction spectroscopy, scanning electron microscopy with energy-dispersive X-ray analysis (SEM/EDX) and scanning transmission electron microscopy with energy-dispersive X-ray analysis (STEM/EDX). The presence of KCl resulted in increased attack, and the service-exposed material had increased attack compared to the as-received TP347H FG material; thus, the deepest attack was observed for KCl-covered previously service-exposed material where grain boundary internal attack occurred. The experimental investigations indicate preferential attack of the Cr-rich precipitates and the presence of chlorine at the corrosion front and Cr-rich precipitates (σ-phase) ahead of the corrosion front for KCl-covered service-exposed material. The findings suggest that service-exposed AISI 347H FG material may experience an increased KCl-induced corrosion attack caused by selective attack of the Cr-rich σ-phase.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (60)

Show source-provided references
1. Tanaka H, Murata M, Abe F, Irie H (2001) Microstructural evolution and change in hardness in type 304H stainless steel during long-term creep. Mater Sci Eng A 319:788–791. https://doi.org/10.1016/S0921-5093(01)01012-710.1016/S0921-5093(01)01012-7 ↗
2. Plaut R, Herrera C, Escriba D (2007) A short review on wrought austenitic stainless steels at high temperatures: processing, microstructure, properties and performance. Mater Res 10:453–460. https://doi.org/10.1590/S1516-1439200700040002110.1590/S1516-14392007000400021 ↗
3. Farneze HN, Maior Tavares Sergio S, Pardal JM et al (2015) Effects of thermal aging on microstructure and corrosion resistance of AISI 317L steel weld metal in the FSW process. Mater Res J Mater 18:98–103. https://doi.org/10.1590/1516-1439.34541410.1590/1516-1439.345414 ↗
4. Jonsson T, Karlsson S, Hooshyar H et al (2016) Oxidation after breakdown of the chromium-rich scale on stainless steels at high temperature: internal oxidation. Oxid Met 85:509–536. https://doi.org/10.1007/s11085-016-9610-710.1007/s11085-016-9610-7 ↗
5. Nielsen HP, Baxter LL, Sclippab G et al (2000) Deposition of potassium salts on heat transfer surfaces in straw-fired boilers: a pilot-scale study. Fuel 79:131–139. https://doi.org/10.1016/S0016-2361(99)00090-310.1016/S0016-2361(99)00090-3 ↗
6. Frandsen FJ (2005) Utilizing biomass and waste for power production—a decade of contributing to the understanding, interpretation and analysis of deposits and corrosion products. Fuel 84:1277–1294. https://doi.org/10.1016/j.fuel.2004.08.02610.1016/j.fuel.2004.08.026 ↗
7. Blomberg T (2006) Which are the right test conditions for the simulation of high temperature alkali corrosion in biomass combustion? Mater Corros 57:170–175. https://doi.org/10.1002/maco.20050390510.1002/maco.200503905 ↗
8. Israelsson N, Hellström K, Svensson JE, Johansson LG (2014) KCl-induced corrosion of the FeCrAl alloy Kanthal® AF at 600 °C and the effect of H2O. Oxid Met 83:1–27. https://doi.org/10.1007/s11085-014-9506-310.1007/s11085-014-9506-3 ↗
9. Pettersson J, Asteman H, Svensson JE-E, Johansson L-GG (2005) KCl induced corrosion of a 304-type austenitic stainless steel at 600°C; the role of potassium. Oxid Met 64:23–41. https://doi.org/10.1007/s11085-005-5704-310.1007/s11085-005-5704-3 ↗
10. O’Hagan CP, O’Brien BJ, Leen SB, Monaghan RFD (2015) A microstructural investigation into the accelerated corrosion of P91 steel during biomass co-firing. Corros Sci 109:101–114. https://doi.org/10.1016/j.corsci.2016.03.02810.1016/j.corsci.2016.03.028 ↗
11. Hansson AN, Pantleon K, Grumsen FB, Somers MAJ (2010) Microstructure evolution during steam oxidation of a Nb stabilized austenitic stainless steel. Oxid Met 73:289–309. https://doi.org/10.1007/s11085-009-9182-x10.1007/s11085-009-9182-x ↗
12. Halvarsson M, Tang JE, Asteman H et al (2006) Microstructural investigation of the breakdown of the protective oxide scale on a 304 steel in the presence of oxygen and water vapour at 600 °C. Corros Sci 48:2014–2035. https://doi.org/10.1016/j.corsci.2005.08.01210.1016/j.corsci.2005.08.012 ↗
13. Asteman H, Svensson J-E, Norell M, Johansson L-G (2000) Influence of water vapor and flow rate on the high-temperature oxidation of 304L; effect of chromium oxide hydroxide evaporation. Oxid Met 54:11–26. https://doi.org/10.1023/A:100464231097410.1023/A:1004642310974 ↗
14. Asteman H, Svensson J-E, Johansson L-G (2002) Oxidation of 310 steel in H2O/O2 mixtures at 600 °C: the effect of water-vapour-enhanced chromium evaporation. Corros Sci 44:2635–2649. https://doi.org/10.1016/S0010-938X(02)00056-210.1016/S0010-938X(02)00056-2 ↗
15. Pettersson J, Svensson J-E, Johansson L-G (2009) KCl-induced corrosion of a 304-type austenitic stainless steel in O2 and in O2 + H2O environment: the influence of temperature. Oxid Met 72:159–177. https://doi.org/10.1007/s11085-009-9153-210.1007/s11085-009-9153-2 ↗
16. Wang F, Shu Y (2003) Influence of Cr content on the corrosion of Fe–Cr alloys: the synergistic effect of NaCl and water vapor. Oxid Met 59:201–214. https://doi.org/10.1023/A:102308330904110.1023/A:1023083309041 ↗
17. Shu Y, Wang F, Wu W (1999) Synergistic effect of NaCl and water vapor on the corrosion of 1Cr11Ni2 W-2MoV steel at 500–700°C. Oxid Met OXIDAT Met 51:97–110. https://doi.org/10.1023/A:101885420298210.1023/A:1018854202982 ↗
18. Okoro SC, Montgomery M, Frandsen FJ, Pantleon K (2015) Effect of water vapor on high-temperature corrosion under conditions mimicking biomass firing. Energy Fuels 29:5802–5815. https://doi.org/10.1021/acs.energyfuels.5b0104510.1021/acs.energyfuels.5b01045 ↗
19. Erneman J, Nylöf L, Nilsson J-O, Andrén H-O (2004) Quantitative metallography of sigma phase precipitates in AISI 347 stainless steel—a comparison between different methods. Mater Sci Technol 20:1245–1251. https://doi.org/10.1179/02670830422502224110.1179/026708304225022241 ↗
20. Erneman J, Schwind M, Nylöf L et al (2005) Comparison between quantitative metallography and modeling of σ-phase particle growth in AISI 347 stainless steel. Metall Mater Trans A 36:2595–2600. https://doi.org/10.1007/s11661-005-0257-210.1007/s11661-005-0257-2 ↗
21. Tavares SSM, Moura V, da Costa VC et al (2009) Microstructural changes and corrosion resistance of AISI 310S steel exposed to 600–800 °C. Mater Charact 60:573–578. https://doi.org/10.1016/j.matchar.2008.12.00510.1016/j.matchar.2008.12.005 ↗
22. West D, Hulance J, Higginson RL, Wilcox GD (2013) σ-phase precipitation in 347HFG stainless steel. Mater Sci Technol 29:835–842. https://doi.org/10.1179/1743284712Y.000000010010.1179/1743284712Y.0000000100 ↗
23. Della Rovere CA, Castro-Rebello M, Kuri SE (2013) Corrosion behavior analysis of an austenitic stainless steel exposed to fire. Eng Fail Anal 31:40–47. https://doi.org/10.1016/j.engfailanal.2013.01.04410.1016/j.engfailanal.2013.01.044 ↗
24. Minami Y, Kimura H, Ihara Y (1986) Microstructural changes in austenitic stainless steels during long-term aging. Mater Sci Technol 2:795–806. https://doi.org/10.1179/mst.1986.2.8.79510.1179/mst.1986.2.8.795 ↗
25. Meier GH, Jung K, Mu N et al (2010) Effect of alloy composition and exposure conditions on the selective oxidation behavior of ferritic Fe–Cr and Fe–Cr–X alloys. Oxid Met 74:319–340. https://doi.org/10.1007/s11085-010-9215-510.1007/s11085-010-9215-5 ↗
26. Giggins CS, Pettit FS (1980) Corrosion of metals and alloys in mixed gas environments at elevated temperatures. Oxid Met I:363–413. https://doi.org/10.1007/BF0060360910.1007/BF00603609 ↗
27. Huenert D, Kranzmann A (2011) Impact of oxyfuel atmospheres H2O/CO2/O2 and H2O/CO2 on the oxidation of ferritic-martensitic and austenitic steels. Corros Sci 53:2306–2317. https://doi.org/10.1016/j.corsci.2011.03.01510.1016/j.corsci.2011.03.015 ↗
28. Guan K, Xu X, Xu H, Wang Z (2005) Effect of aging at 700 °C on precipitation and toughness of AISI 321 and AISI 347 austenitic stainless steel welds. Nucl Eng Des 235:2485–2494. https://doi.org/10.1016/j.nucengdes.2005.06.00610.1016/j.nucengdes.2005.06.006 ↗
29. Malede YC, Montgomery M, Dahl KV, Hald J (2018) Effect of microstructure on KCl corrosion attack of modified AISI 310 steel. Mater High Temp 35:243–254. https://doi.org/10.1080/09603409.2017.138938110.1080/09603409.2017.1389381 ↗
30. Korcakova L, Montgomery M, Jensen HT, Ab V (2013) Investigations of superheater materials from Nordjyllandsværket coal-fired plant after 100000 hours service. In: Auerkari P, Veivo J (eds) International conference on life management and maintenance for power plants. VTT Technology 106, pp 458–476
31. Astm Standard (2012) E112-12:Standard Test methods for determining average grain size. ASTM Int E112-12:1–27. https://doi.org/10.1520/E0112-12.1.410.1520/E0112-12.1.4 ↗
32. Kiamehr S, Dahl KV, Montgomery M, Somers MAJ (2016) KCl-induced high temperature corrosion of selected commercial alloys: part II: alumina and silica-formers. Mater Corros 67:26–38. https://doi.org/10.1002/maco.20140821510.1002/maco.201408215 ↗
33. Jan-Olof A, Helander T, Höglund L et al (2002) Thermo-Calc & DICTRA, computational tools for materials science. Calphad 26:273–312. https://doi.org/10.1016/S0364-5916(02)00037-810.1016/S0364-5916(02)00037-8 ↗
34. Villanueva DME, Junior FCP, Plaut RL, Padilha AF (2006) Comparative study on sigma phase precipitation of three types of stainless steels: austenitic, superferritic and duplex. Mater Sci Technol 22:1098–1104. https://doi.org/10.1179/174328406X10923010.1179/174328406X109230 ↗
35. van der Pluijm BA, Lee JH, Peacor DR (1988) Analytical electron microscopy and the problem of potassium diffusion. Clays Clay Miner 36:498–50410.1346/CCMN.1988.0360603 ↗
36. Goldstein JI, Newbury DE, Michael JR et al (2018) Trace analysis by SEM/EDS. Scanning electron microscopy and X-ray microanalysis. Springer, New York, pp 341–35710.1007/978-1-4939-6676-9_21 ↗
37. Padilha AF, Rios PR (2002) Decomposition of austenite in austenitic stainless steels. ISIJ Int 42:325–327. https://doi.org/10.2355/isijinternational.42.32510.2355/isijinternational.42.325 ↗
38. Gheno T, Monceau D, Young DJ (2013) Kinetics of breakaway oxidation of Fe–Cr and Fe–Cr–Ni alloys in dry and wet carbon dioxide. Corros Sci 77:246–256. https://doi.org/10.1016/j.corsci.2013.08.00810.1016/j.corsci.2013.08.008 ↗
39. Ericsson T (1970) A study of the Cr-depleted surface layers formed on four Cr–Ni steels during oxidation in steam at 600 °C and 800 °C. Oxid Met 2:401–417. https://doi.org/10.1007/BF0060447810.1007/BF00604478 ↗
40. Jonsson T, Froitzheim J, Pettersson J et al (2009) The influence of KCl on the corrosion of an Austenitic stainless steel (304L) in oxidizing humid conditions at 600°C: a microstructural study. Oxid Met 72:213–239. https://doi.org/10.1007/s11085-009-9156-z10.1007/s11085-009-9156-z ↗
41. Mu N, Jung KY, Yanar NM et al (2012) Water vapor effects on the oxidation behavior of Fe–Cr and Ni–Cr alloys in atmospheres relevant to oxy-fuel combustion. Oxid Met 78:221–237. https://doi.org/10.1007/s11085-012-9302-x10.1007/s11085-012-9302-x ↗
42. Streicher MA, Begum S (2016) Corrosion, intergranular. Reference module in materials science and materials engineering. Elsevier, Amsterdam, pp 3–5
43. Engelberg DL (2010) Intergranular corrosion. Shreir’s corrosion. Elsevier, Amsterdam, pp 810–82710.1016/B978-044452787-5.00032-9 ↗
44. Kim CS, Moon SJ, Kong WS (2016) Effect of sensitization treatment on corrosion properties in austenitic stainless steel 304. Mater Sci Forum 857:232–236. https://doi.org/10.4028/www.scientific.net/MSF.857.23210.4028/www.scientific.net/MSF.857.232 ↗
45. Matula M, Hyspecka L, Svoboda M et al (2001) Intergranular corrosion of AISI 316L steel. Mater Charact 46:203–210. https://doi.org/10.1016/S1044-5803(01)00125-510.1016/S1044-5803(01)00125-5 ↗
46. Trindade VB, Krupp U, Hanjari BZ et al (2005) Effect of alloy grain size on the high-temperature oxidation behavior of the austenitic steel TP 347. Mater Res 8:371–375. https://doi.org/10.1590/S1516-1439200500040000310.1590/S1516-14392005000400003 ↗
47. Peng X, Yan J, Zhou Y, Wang F (2005) Effect of grain refinement on the resistance of 304 stainless steel to breakaway oxidation in wet air. Acta Mater 53:5079–5088. https://doi.org/10.1016/j.actamat.2005.07.01910.1016/j.actamat.2005.07.019 ↗
48. Teranishi H, Sawaragi Y, Kubota M, Hayase Y (1989) Fine-grained TP 347 H steel tubing with high elevated-temperature strength and corrosion resistance for boiler applications
49. Kim JH, Kim DI, Suwas S et al (2013) Grain-size effects on the high-temperature oxidation of modified 304 austenitic stainless steel. Oxid Met 79:239–247. https://doi.org/10.1007/s11085-012-9347-x10.1007/s11085-012-9347-x ↗
50. Fujikawa H, Iijima Y (2013) Effect of grain size on the high temperature oxidation behaviour of austenitic stainless steels. Defect Diffus Forum 333:149–155. https://doi.org/10.4028/www.scientific.net/DDF.333.14910.4028/www.scientific.net/DDF.333.149 ↗
51. Viitala H, Galfi I, Taskinen P (2015) Initial oxidation behaviour of niobium stabilized TP347H austenitic stainless steel—effect of grain size and temperature. Mater Corros 66:851–862. https://doi.org/10.1002/maco.20140794810.1002/maco.201407948 ↗
52. Li YS, Spiegel M, Shimada S (2005) Corrosion behaviour of various model alloys with NaCl–KCl coating. Mater Chem Phys 93:217–223. https://doi.org/10.1016/j.matchemphys.2005.03.01510.1016/j.matchemphys.2005.03.015 ↗
53. Liu C, Little JA, Henderson PJ, Ljung P (2001) Corrosion of TP347H FG stainless steel in a biomass fired PF utility boiler. J Mater Sci 36:1015–1026. https://doi.org/10.1023/A:100484441174410.1023/A:1004844411744 ↗
54. Grabke HJ, Reese E, Spiegel M (1995) The effects of chlorides, hydrogen chloride, and sulfur dioxide in the oxidation of steels below deposits. Corros Sci 37:1023–1043. https://doi.org/10.1016/0010-938X(95)00011-810.1016/0010-938X(95)00011-8 ↗
55. Nguyen TD, Zhang J, Young DJ (2014) Effects of silicon on high temperature corrosion of Fe–Cr and Fe–Cr–Ni alloys in carbon dioxide. Oxid Met 81:549–574. https://doi.org/10.1007/s11085-013-9467-y10.1007/s11085-013-9467-y ↗
56. Li YSS, Spiegel M, Shimada S (2004) Effect of Al/Si addition on KCl induced corrosion of 9% Cr steel. Mater Lett 58:3787–3791. https://doi.org/10.1016/j.matlet.2004.06.06810.1016/j.matlet.2004.06.068 ↗
57. Bender R, Schütze M (2003) The role of alloying elements in commercial alloys for corrosion resistance in oxidizing-chloridizing atmospheres. Part I: literature evaluation and thermodynamic calculations on phase stabilities. Mater Corros 54:567–586. https://doi.org/10.1002/maco.20039012910.1002/maco.200390129 ↗
58. Latreche H, Doublet S, Schütze M (2009) Development of corrosion assessment diagrams for high temperature chlorine corrosion. Part I: state of the art and development of the basis for a new extended approach. Oxid Met 72:1–30. https://doi.org/10.1007/s11085-009-9147-010.1007/s11085-009-9147-0 ↗
59. Grabke HJ, Spiegel M, Zahs A (2004) Role of alloying elements and carbides in the chlorine-induced corrosion of steels and alloys. Mater Res 7:89–95. https://doi.org/10.1590/S1516-1439200400010001310.1590/S1516-14392004000100013 ↗
60. Uusitalo MA, Backman R, Berger L-M et al (2002) Oxidation resistance of carbides in chlorine-containing atmospheres. High Temp Mater Process 21:307–320. https://doi.org/10.1515/HTMP.2002.21.5.30710.1515/HTMP.2002.21.5.307 ↗