journal article·2003-02

Cavitation damage to geomaterials in a flowing system

A. W. Momber

Journal of Materials Science· Volume 38· Issue 4
Publisher page

Abstract

Short-time cavitation erosion of rocks and cementitious composites is investigated in a laboratory flow cavitation chamber. Cavitation erosion with an exposure time as low as 10 seconds generates measurable damage. Mineral composition plays a major role in the cavitation erosion of the material. The erosion mainly occurs in an intergranular or intercrystalline mode, respectively. Fracture toughness of rock and conventional concrete is a good indication of cavitation erosion resistance. However, density is a second important evaluation parameter; materials with a low degree of pre-existing flaws, namely glass and high-strength silica cement, show an extraordinary high erosion resistance. The cavitation erosion of the rock materials tested in this study is always higher than that of conventional concrete mixtures. Elastic strain energy density is not a measure of cavitation erosion resistance of rocks and cementitious composites. A parameter Φ = dM · EM · ρM/KIcn is derived to approximate the cavitation erosion resistance of the materials. The parameter n is a function of the R-curve-behavior.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Coal Combustion and Slurry Processing · Ultrasound and Cavitation Phenomena · Erosion and Abrasive Machining

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. A. A Ribeiro, L. V. Da cunha, D. P. Da Silva and F. O Lemos, in Proc. 9th Int. Congress on Large Dams, Istambul, 1967, Vol. 2, p. 315.
2. R. Clancy, D. Mark and B. Christopher, in 4th Int. Symp. on Cavitation, Pasadena, June 2001, p. 20–23.
3. F. A. Angona, Int. J. Rock Mech. Min. Sci. & Geomech. Abstr. 11 (1974) 115.10.1016/0148-9062(74)92871-X ↗
4. A. F. Conn and R. P. Radtke, The Oil and Gas J. (1977) 129.
5. M. Mazurkiewicz and D. A. Summers, in Proc. 6th Int. Symp. Jet Cutting Technology, edited by H. S. Stephens and E. B. Davies (BHRA, Cranfield, 1982) p. 27.
6. N. K. Bourne, T. Obara and J. E. Field, Proc. Roy. Soc. London, Ser. A 452 (1996) 1497.
7. F. Erdmann-Jesnitzer, H. Louis and Wiedemeier, in Proc. 4th Int. Symp. Jet Cutting Technol., edited by J. Clarke and H. S. Stephens (BHRA, Cranfield, 1978) p. 29.
8. A. W. Momber, Wear 241 (2000) 47.10.1016/S0043-1648(00)00348-3 ↗
9. F.G. Hammitt, “Cavitation and Multiphase Flow Phenomena” (McGraw-Hill, New York, 1980).
10. W. H. Isay, “Kavitation” (Schiffahrts-Verlag, Hamburg, 1989).
11. R. T. Knapp, J. T. Daily and F. H. Hammitt, “Cavitation” (McGraw-Hill, New York, 1979).
12. W. Lauterborn and H. Bolle, J. Fluid Mech. 72 (1975) 391.10.1017/S0022112075003448 ↗
13. J. P. Dear and J. E. Field, ibid. 190 (1988) 409.10.1017/S0022112088001387 ↗
14. R. P. Tong, W. Schiffers, S. J. Shaw, J. R. Blake and D. C. Emmony, ibid. 380 (1999) 339.10.1017/S0022112098003589 ↗
15. Y. Murakami, “Stress Intensity Handbook,” Vol. 1 (Pergamon Press, Oxford, 1987) p. 13.
16. F. Erdmann-Jesnitzer and H. Louis, in “5. Sitzung Arbeitskreis Bruchvorgänge” (Deutscher Verband für Materialprüfung, Karlsruhe, 1973) p. 101.
17. M. S. Plesset and R. B. Chapman, J. Fluid Mech. 2 (1971) 283.10.1017/S0022112071001058 ↗
18. P. T. Tai, Personal communication, Institute of Materials Science, Hanover University, 2000.
19. J. E. Field, in “Tribology in Particulate Technology,” edited by B. J. Briscoe and M. J. Adams (Adam Hilger, Bristol, 1987) p. 416.
20. N. K. Bourne and J. E. Field, J. Appl. Phys. 78 (1995) 4423.10.1063/1.359850 ↗
21. I. M. Daniels and R. E. Rowlands, Exper. Mechan. (1975) 449.
22. E. U. Waldherr, PhD thesis, Ruhr-University, Bochum, 1991.
23. C. M. Preece and I. L. Hansson, in Proc. 6th Int. Conf on Erosion by Liquid and Solid Impact, edited by J. E. Field (Cavendish Laboratory, Cambridge, UK, 1986) p. 3/1.
24. B. Lin, G. Shan and Y. Cai, in Proc. 3rd CANMET/ACI Conf. on High-Performance Concrete, Kuala Lumpur, 1997, p. 485.
25. W. J. Tomlinson, N. Nalitsounakis and G. Vekinis, Ceramics Int. 25 (1999) 331.10.1016/S0272-8842(98)00043-1 ↗
26. A. Thiruvengadam, in “ASTM STP 403” (ASTM, Philadelphia, 1967), p. 22.
27. F. J. Heymann, in “ASTM STP 474” (ASTM, Philadelphia, 1970) p. 212.
28. P. S. Shah and C. Ouyang, ASME J. Engng. Mater. and Technol. 115 (1993) 300.10.1115/1.2904222 ↗
29. A. W. Momber, Int. J. Fracture 112 (2001) 99.10.1023/A:1013367729746 ↗
30. G. C. Sih and E. E. Gdoutos, “Mechanics and Physics of Energy Density” (Kluwer Acad. Publ., Dordrecht, 1992).