Effective X-ray elastic constant of cast iron
Source abstract
Abstract
X-ray diffraction is a non-destructive method used for strain measurements in crystalline materials. Conversion of strain to stress can be achieved using the X-ray elastic constants (XEC), s 1 and ½s 2. The sin2 ψ method was used during in situ loading to determine XEC for flake, vermicular, and spherical graphite iron. A fully pearlitic steel was used as reference. Uniaxial testing was conducted on the cast iron to create a homogeneous strain field, as well as four-point bending in both tension and compression due to the tension/compression asymmetry. The commonly used XEC value ½s 2 = 5.81 × 10−6 MPa−1 is theoretically derived from an α-Fe single crystal. When investigating materials that contain ferrite, such as polycrystalline cast iron, this value is not accurate. Determination of an effective XEC for polycrystalline cast iron yields a better correlation between the measured microstrains and the properties observed on a macroscopic scale. The need for an effective XEC is evident, especially when it comes to model validation of, for example, casting simulations. Effective XEC values have been determined for flake, vermicular, and spherical graphite iron. The determined value is lower than the theoretical value.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (11)
Show source-provided references
1. Noyan IC, Cohan JB (1987) Residual stress, 1st edn. doi: 10.1007/978-1-4613-9570-610.1007/978-1-4613-9570-6 ↗
2. Hilley ME, Larson JA, Jatczak CF, Ricklefs RE (1971) Residual stress measurement by X-ray diffraction—SAE J784a. Society of Automotive Engineers INC, Warrendale
3. Hauk V, Behnken H (1997) Structural and residual stress analysis by nondestructive methods: evaluation, application, assessment. Elsevier, Amsterdam
4. Lu J, for Experimental Mechanics (US) S (1996) Handbook of measurement of residual stresses. Fairmont Press, New York
5. Hauk V, Wolfsteig U (1976) Röntgenographische Elastizitätskonstanten. J heat Treat Mater 31:38–4210.1515/htm-1976-311-208 ↗
6. Kamaladasa RJ, Picard YN (2010) Basic principles and application of electron channeling in a scanning electron microscope for dislocation analysis. Microsc Sci Technol Appl Edu 3:1583–1590
7. Gutierrez-Urrutia I, Zaefferer S, Raabe D (2009) Electron channeling contrast imaging of twins and dislocations in twinning-induced plasticity steels under controlled diffraction conditions in a scanning electron microscope. Scr Mater 61:737–740. doi: 10.1016/j.scriptamat.2009.06.01810.1016/j.scriptamat.2009.06.018 ↗
8. Lundberg M, Saarimäki J, Peng RL, Moverare JJ (2017) Residual stresses in uniaxial cyclic loaded pearlitic lamellar graphite iron. Mater Res Proc 2:67–72. doi: 10.21741/9781945291173-1210.21741/9781945291173-12 ↗
9. Marion RH, Cohen JB (1976) The need for experimentally determined X-ray elastic constants. Evanston, IL10.21236/ADA030616 ↗
10. Prevey PS (1977) A method of determining the elastic properties of alloys in selected crystallographic directions for X-ray diffraction residual stress measurement. Adv X Ray Anal 20:345–35410.1154/S0376030800011952 ↗
11. Prevéy PS (1986) X-ray diffraction residual stress techniques. Met Handbook 10 Met Park 380–392. doi: 10.1361/asmhba000176110.1361/asmhba0001761 ↗