Texture-governed electrochemical corrosion behaviour of AA 6082 alloy
Source abstract
Abstract
The variations of through-thickness corrosion behaviour with the β-fibre evolution of hot-rolled AA 6082 alloy at the sub-surface layer (SL), quarter layer and middle layer (ML) in 3.5 wt% NaCl solution were mainly investigated by EIS, potentiodynamic polarization, SEM, XRD and 3D-MLM. Results showed that the strong β-fibre (rolling) and shear orientation formed at ML and SL, respectively. Compared to ML, charge transfer resistance increased, whereas double-layer capacitance was reduced at SL. From ML to SL, corrosion current density decreased and corrosion potential and pitting potential rose successively. Moreover, the deepened pits occurred at ML. Based on the surface energy of Al in the order (111) < (100) < (110)/high-index planes, the worse corrosion resistance at ML with strong β-fibre orientation stemmed from the high surface energy. As a consequence, the available shear textures are beneficial to improving the corrosion resistance. This provides a new design strategy to enhance the corrosion resistance for the commercial Al alloys.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Corrosion Behavior and Inhibition
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (67)
Show source-provided references
1. Liu M, Qiu D, Zhao MC, Song GL, Atrens A (2008) The effect of crystallographic orientation on the active corrosion of pure magnesium. Scr Mater 58:421–42410.1016/j.scriptamat.2007.10.027 ↗
2. Li X, Jiang B, He JJ, Zhang JY, Jiang ZT, Liu B, Pan FS (2017) Improvement of planar isotropy, mechanical properties and corrosion resistance of extruded Mg–3Al–1Zn alloy sheet by special grain re-orientation. J Alloys Compd 721:106–11710.1016/j.jallcom.2017.05.324 ↗
3. Jiang B, Xiang Q, Atrens A, Song JF, Pan FS (2017) Influence of crystallographic texture and grain size on the corrosion behaviour of as-extruded Mg alloy AZ31 sheets. Corros Sci 126:374–38010.1016/j.corsci.2017.08.004 ↗
4. Bland LG, Gusieva K, Scully JR (2017) Effect of crystallographic orientation on the corrosion of magnesium: comparison of film forming and bare crystal facets using electrochemical impedance and Raman spectroscopy. Electrochim Acta 227:136–15110.1016/j.electacta.2016.12.107 ↗
5. He JJ, Jiang B, Xu J, Zhang JY, Yu XW, Liu B, Pan FS (2017) Effect of texture symmetry on mechanical performance and corrosion resistance of magnesium alloy sheet. J Alloys Compd 723:213–22410.1016/j.jallcom.2017.06.269 ↗
6. Hagihara K, Okubo M, Yamasaki M, Nakano T (2016) Crystal-orientation-dependent corrosion behaviour of single crystals of a pure Mg and Mg–Al and Mg–Cu solid solutions. Corros Sci 109:68–8510.1016/j.corsci.2016.03.019 ↗
7. Jiang QT, Ma XM, Zhang K, Li YT, Li XG, Li YJ, Ma ML, Hou BR (2015) Anisotropy of the crystallographic orientation and corrosion performance of high-strength AZ80 Mg alloy. J Magn Alloy 3:309–31410.1016/j.jma.2015.11.002 ↗
8. Yang L, Zhou XR, Curioni M, Pawar S, Liu H, Fan ZY, Scamans G, Thompson G (2015) Corrosion behavior of pure magnesium with low iron content in 3.5 wt% NaCl solution. J Electrochem Soc 162:C362–C36810.1149/2.1041507jes ↗
9. Wang BJ, Xu DK, Dong JH, Ke W (2014) Effect of the crystallographic orientation and twinning on the corrosion resistance of an as-extruded Mg–3Al–1Zn (wt%) bar. Scr Mater 88:5–810.1016/j.scriptamat.2014.06.015 ↗
10. Song GL, Xu ZQ (2012) Crystal orientation and electrochemical corrosion of polycrystalline Mg. Corros Sci 63:100–11210.1016/j.corsci.2012.05.019 ↗
11. Chojnacka A, Kawalko J, Koscielny H, Guspiel J, Drewienkiewicz A, Bieda M, Pachla W, Kulczyk M, Sztwiertnia K, Beltowska-Lehman E (2017) Corrosion anisotropy of titanium deformed by the hydrostatic extrusion. Appl Surf Sci 426:987–99410.1016/j.apsusc.2017.07.231 ↗
12. Dai NW, Zhang LC, Zhang JX, Zhang X, Ni QZ, Chen Y, Wu ML, Yang C (2016) Distinction in corrosion resistance of selective laser melted Ti–6Al–4V alloy on different planes. Corros Sci 111:703–71010.1016/j.corsci.2016.06.009 ↗
13. Guo WY, Sun J, Wu JS (2009) Effect of deformation on corrosion behavior of Ti–23Nb–0.7Ta–2Zr–O alloy. Mater Charact 60:173–17710.1016/j.matchar.2008.08.006 ↗
14. Ma Y, Zhou X, Liao Y, Yi Y, Wu H, Wang Z, Huang W (2016) Localised corrosion in AA 2099-T83 aluminium–lithium alloy: the role of grain orientation. Corros Sci 107:41–4810.1016/j.corsci.2016.02.018 ↗
15. Fan L, Lu HM, Leng J, Sun ZG, Chen CB (2015) The effect of crystal orientation on the aluminum anodes of the aluminum-air batteries in alkaline electrolytes. J Power Sources 299:66–6910.1016/j.jpowsour.2015.08.095 ↗
16. Beck G, Funk S (2012) Correlation between optical appearance and orientation of aluminium. Surf Coat Technol 206:2371–237910.1016/j.surfcoat.2011.10.034 ↗
17. Mutasa B, Farkas D (1998) Atomistic structure of high-index surfaces in metals and alloys. Surf Sci 415:312–31910.1016/S0039-6028(98)00552-4 ↗
18. Wang XC, Jia Y, Yao QK, Wang F, Ma JX, Hu X (2004) The calculation of the surface energy of high-index surfaces in metals at zero temperature. Surf Sci 551:179–18810.1016/j.susc.2003.12.034 ↗
19. Brito P, Schuller É, Silva J, Campos TR, Araújo CRD, Carneiro JR (2017) Electrochemical corrosion behaviour of (100), (110) and (111) Fe3Al single crystals in sulphuric acid. Corros Sci 126:366–37310.1016/j.corsci.2017.05.029 ↗
20. Brewick PT, Kota N, Lewis AC, DeGiorgi VG, Geltmacher AB, Qidwai SM (2017) Microstructure-sensitive modeling of pitting corrosion: effect of the crystallographic orientation. Corros Sci 129:54–6910.1016/j.corsci.2017.09.009 ↗
21. Lu ZP, Shoji T, Dan TC, Qiu YB, Yonezawa T (2010) The effect of roll-processing orientation on stress corrosion cracking of warm-rolled 304L stainless steel in oxygenated and deoxygenated high temperature pure water. Corros Sci 52:2547–255510.1016/j.corsci.2010.03.027 ↗
22. Shahryari A, Szpunar JA, Omanovic S (2009) The influence of crystallographic orientation distribution on 316LVM stainless steel pitting behavior. Corros Sci 51:677–68210.1016/j.corsci.2008.12.019 ↗
23. Lv JL, Liang TX, Wang C (2016) Effect of electrodeposition temperature on grain orientation and corrosion resistance of nanocrystalline pure nickel. J Solid State Chem 240:109–11410.1016/j.jssc.2016.05.025 ↗
24. Wang SY, Wang JQ (2014) Effect of grain orientation on the corrosion behavior of polycrystalline Alloy 690. Corros Sci 85:183–19210.1016/j.corsci.2014.04.014 ↗
25. Martinez-Lombardia E, Gonzalez-Garcia Y, Lapeire L, De Graeve I, Verbeken K, Kestens L, Mol JMC, Terryn H (2014) Scanning electrochemical microscopy to study the effect of crystallographic orientation on the electrochemical activity of pure copper. Electrochim Acta 116:89–9610.1016/j.electacta.2013.11.048 ↗
26. Song JM, Zou YS, Kuo CC, Lin SC (2013) Orientation dependence of the electrochemical corrosion properties of electrodeposited Cu foils. Corros Sci 74:223–23110.1016/j.corsci.2013.04.046 ↗
27. Goli F, Jamaati R (2018) Intensifying Goss/Brass texture ratio in AA2024 by asymmetric cold rolling. Mater Lett 219:229–23210.1016/j.matlet.2018.02.124 ↗
28. Zhao Q, Liu ZY, Li SS, Huang TT, Xia P, Lu LQ (2017) Evolution of the Brass texture in an Al-Cu-Mg alloy during hot rolling. J Alloys Compd 691:786–79910.1016/j.jallcom.2016.08.322 ↗
29. Huang YC, Liu Y, Li Q, Liu X, Yang CG (2016) Relevance between microstructure and texture during cold rolling of AA3104 aluminum alloy. J Alloys Compd 673:383–38910.1016/j.jallcom.2016.02.226 ↗
30. Liu WC, Man CS, Raabe D (2010) Effect of strain hardening on texture development in cold rolled Al-Mg alloy. Mat Sci Eng A 527:1249–125410.1016/j.msea.2009.09.059 ↗
31. Liu WC, Kong XY, Chen MB, Li J, Yuan H, Yang QX (2009) Texture development in a pseudo cross-rolled AA 3105 aluminum alloy. Mat Sci Eng A 516:263–26910.1016/j.msea.2009.03.022 ↗
32. Chowdhury SG, Dutta A, Ravikumar B, Kumar A (2006) Textural evolution during accumulative roll bonding of an Al-Li alloy. Mat Sci Eng A 428:351–35710.1016/j.msea.2006.05.055 ↗
33. Wang XF, Guo MX, Cao LY, Luo JR, Zhang JS, Zhuang LZ (2015) Influence of thermomechanical processing on microstructure, texture evolution and mechanical properties of Al–Mg–Si–Cu alloy sheets. T Nonferr Metal Soc 25:1752–176210.1016/S1003-6326(15)63780-3 ↗
34. Chen JZ, Zhen L, Shao WZ, Dai SL, Cui YX (2008) Through-thickness texture gradient in AA 7055 aluminum alloy. Mater Lett 62:88–9010.1016/j.matlet.2007.04.074 ↗
35. Liu WC, Radhakrishnan B, Li Z, Morris JG (2008) Through-thickness texture gradient in continuous cast AA 5052 aluminum alloy sheet. Mat Sci Eng A 472:170–17810.1016/j.msea.2007.03.024 ↗
36. Kamikawa N, Tsuji N, Huang XX, Hansen N (2007) Through-Thickness Characterization of Microstructure and Texture in High Purity Aluminum Processed to High Strain by Accumulative Roll-Bonding. Mater Trans 48:1978–198510.2320/matertrans.MA200702 ↗
37. Engler O, Hirsch J (2002) Texture control by thermomechanical processing of AA6xxx Al-Mg-Si sheet alloys for automotive applications—a review. Mat Sci Eng A 336:249–26210.1016/S0921-5093(01)01968-2 ↗
38. Daaland O, Nes E (1996) Origin of Cube Texture During Hot Rolling of Commercial Al-Mn-Mg Alloys. Acta Mater 44:1389–141110.1016/1359-6454(95)00289-8 ↗
39. Zhang F, Evertsson J, Bertram F, Rullik L, Carla F, Långberg M, Lundgren E, Pan JS (2017) Integration of electrochemical and synchrotron-based X-ray techniques for in situ investigation of aluminum anodization. Electrochim Acta 241:299–30810.1016/j.electacta.2017.04.154 ↗
40. Esmaily M, Mortazavi N, Osikowicz W, Hindsefelt H, Svensson JE, Halvarsson M, Thompson GE, Johansson LG (2016) Influence of Multi-Pass Friction Stir Processing on the Corrosion Behavior of an Al-Mg-Si Alloy. J Electrochem Soc 163:C124–C13010.1149/2.1091603jes ↗
41. Li H, Zhao PP, Wang ZX, Mao QZ, Fang BJ, Song RG, Zheng ZQ (2016) The intergranular corrosion susceptibility of a heavily overaged Al-Mg-Si-Cu alloy. Corros Sci 107:113–12210.1016/j.corsci.2016.02.025 ↗
42. Kumar N, Rao PN, Jayaganthan R, Brokmeier H (2015) Effect of cryorolling and annealing on recovery, recrystallisation, grain growth and their influence on mechanical and corrosion behaviour of 6082 Al alloy. Mater Chem Phys 165:177–18710.1016/j.matchemphys.2015.09.014 ↗
43. Wu YN, Liao HC (2013) Corrosion Behavior of Extruded near Eutectic Al-Si-Mg and 6063 Alloys. J Mater Sci Technol 29:380–38610.1016/j.jmst.2013.02.001 ↗
44. Laurino A, Andrieu E, Harouard J, Lacaze J, Lafont M, Odemer G, Blanc C (2013) Corrosion Behavior of 6101 Aluminum Alloy Strands for Automotive Wires. J Electrochem Soc 160:C569–C57510.1149/2.080311jes ↗
45. Händel M, Nickel D, Lampke T (2011) Effect of different grain sizes and textures on the corrosion behaviour of aluminum alloy AA6082. Materialwiss Werkst 42:606–61110.1002/mawe.201100829 ↗
46. Hockauf M, Meyer LW, Nickel D, Alisch G, Lampke T, Wielage B, Krüger L (2008) Mechanical properties and corrosion behaviour of ultrafine-grained AA6082 produced by equal-channel angular pressing. J Mater Sci 43:7409–7417. https://doi.org/10.1007/s10853-008-2724-910.1007/s10853-008-2724-9 ↗
47. Gerengi H, Slepski P, Ozgan E, Kurtay M (2015) Investigation of corrosion behavior of 6060 and 6082 aluminum alloys under simulated acid rain conditions. Mater Corros 66:233–24010.1002/maco.201307287 ↗
48. Comotti IM, Trueba M, Trasatti SP (2013) The pit transition potential in the repassivation of aluminium alloys. Surf Interface Anal 45:1575–158410.1002/sia.5270 ↗
49. Panagopoulos CN, Georgiou EP, Gavras AG (2009) Corrosion and wear of 6082 aluminum alloy. Tribol Int 42:886–88910.1016/j.triboint.2008.12.002 ↗
50. Huang YL, Shih H, Huang HC, Daugherty J, Wu S, Ramanathan S, Chang C, Mansfeld F (2008) Evaluation of the corrosion resistance of anodized aluminum 6061 using electrochemical impedance spectroscopy (EIS). Corros Sci 50:3569–357510.1016/j.corsci.2008.09.008 ↗
51. Lv JL, Luo HY (2013) Effect of surface burnishing on texture and corrosion behavior of 2024 aluminum alloy. Surf Coat Technol 235:513–52010.1016/j.surfcoat.2013.07.071 ↗
52. Zhang GA, Xu LY, Cheng YF (2009) Investigation of erosion-corrosion of 3003 aluminum alloy in ethylene glycol-water solution by impingement jet system. Corros Sci 51:283–29010.1016/j.corsci.2008.10.026 ↗
53. Li Q, Xu SQ, Hu JY, Zhang SY, Zhong XK, Yang XK (2010) The effects to the structure and electrochemical behavior of zinc phosphate conversion coatings with ethanolamine on magnesium alloy AZ91D. Electrochim Acta 55:887–89410.1016/j.electacta.2009.06.048 ↗
54. Ma HY, Cheng XL, Li GQ, Chen SH, Quan ZL, Zhao SY, Niu L (2000) The influence of hydrogen sulfide on corrosion of iron under different conditions. Corros Sci 42:1669–168310.1016/S0010-938X(00)00003-2 ↗
55. Wang DP, Yang D, Zhang DQ, Li K, Gao LX, Lin T (2015) Electrochemical and DFT studies of quinoline derivatives on corrosion inhibition of AA5052 aluminium alloy in NaCl solution. Appl Surf Sci 357:2176–218310.1016/j.apsusc.2015.09.206 ↗
56. Wu XJ, Ma HY, Chen SH, Xu ZY, Sui AF (1999) General equivalent circuits for Faradaic electrode processes under electrochemical reaction control. J Electrochem Soc 146:1847–185310.1149/1.1391854 ↗
57. Tang JW, Shao YW, Guo JB, Zhang T, Meng GZ, Wang FH (2010) The effect of H2S concentration on the corrosion behavior of carbon steel at 90 C. Corros Sci 52:2050–205810.1016/j.corsci.2010.02.004 ↗
58. Veloz MA, González I (2002) Electrochemical study of carbon steel corrosion in buffered acetic acid solutions with chlorides and H2S. Electrochim Acta 48:135–14410.1016/S0013-4686(02)00549-2 ↗
59. Liu J, Wang DP, Gao LX, Zhang DQ (2016) Synergism between cerium nitrate and sodium dodecylbenzenesulfonate on corrosion of AA5052 aluminium alloy in 3 wt% NaCl solution. Appl Surf Sci 389:369–37710.1016/j.apsusc.2016.07.107 ↗
60. Wen L, Wang YM, Zhou Y, Ouyang JH, Guo LX, Jia DC (2010) Corrosion evaluation of microarc oxidation coatings formed on 2024 aluminium alloy. Corros Sci 52:2687–269610.1016/j.corsci.2010.04.022 ↗
61. Sherif EM, Park SM (2006) Effects of 1,4-naphthoquinone on aluminum corrosion in 0.50 M sodium chloride solutions. Electrochim Acta 51:1313–132110.1016/j.electacta.2005.06.018 ↗
62. Song YW, Shan DY, Chen RS, Han EH (2009) Corrosion characterization of Mg–8Li alloy in NaCl solution. Corros Sci 51:1087–109410.1016/j.corsci.2009.03.011 ↗
63. Li Y, Xu J (2017) Is niobium more corrosion-resistant than commercially pure titanium in fluoride-containing artificial saliva? Electrochim Acta 233:151–16610.1016/j.electacta.2017.03.015 ↗
64. Beneaa L, Celisb JP (2018) Reactivity of porous titanium oxide film and chitosan layer electrochemically formed on Ti–6Al–4V alloy in biological solution. Surf Coat Technol 354:145–15210.1016/j.surfcoat.2018.09.015 ↗
65. Yasakau KA, Zheludkevich ML, Lamaka SV, Ferreira MGS (2007) Role of intermetallic phases in localized corrosion of AA5083. Electrochim Acta 52:7651–765910.1016/j.electacta.2006.12.072 ↗
66. Trueba M, Trasatti SP (2010) Study of Al alloy corrosion in neutral NaCl by the pitting scan technique. Mater Chem Phys 121:523–53310.1016/j.matchemphys.2010.02.022 ↗
67. Zhang JY, Ma MY, Shen FH, Yi DQ, Wang B (2018) Influence of deformation and annealing on electrical conductivity, mechanical properties and texture of Al–Mg–Si alloy cables. Mat Sci Eng A 710:27–3710.1016/j.msea.2017.10.065 ↗