Microstructural and mechanical insights into 1.2709 maraging steel produced by direct energy deposition
Source abstract
Abstract
Abstract The present work focuses on the characterization of the ultra-high-strength 1.2709 maraging steel produced by the Direct Energy Deposition (DED) technique, either in its as-built or as-built + heat-treated state. Scanning electron microscope micrographs and X-ray diffraction patterns showed that the heat treatment (namely, solution annealing and aging) had minimal impact on the microstructure changes of the maraging steel. The material is characterized by fine cellular or dendritic microstructure containing several percent of the ductile γ-austenite phase in both as-built and as-built + heat-treated states. A small amount of the Ni3Mo0.5Ti0.5 intermetallic phase was observed even in the as-built state of the material. The heat treatment caused a substantial improvement of the mechanical properties through the homogeneous precipitation of nano-sized needle-shaped Ni3Mo0.5Ti0.5 intermetallic phase. Tensile yield strength increased from 753 to 1957 MPa, ultimate tensile strength—from 991 to 2024 MPa, and microhardness—from 350 to 700 HV0.1. The present results are also compared with those obtained for the same material produced by the more commonly used Laser Powder Bed Fusion (L-PBF) technique. Despite having a coarser microstructure with a presence of γ-phase than the LPBF-printed material, the DED-printed maraging steel exhibited greater precipitation hardening while maintaining 5% ductility after heat treatment.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (76)
Show source-provided references
1. Madhavadas V, Srivastava D, Chadha U, Raj SA, Sultan MTH, Shahar FS, Shah AUM (2022) A review on metal additive manufacturing for intricately shaped aerospace components. CIRP J Manuf Sci Technol 39:18–3610.1016/j.cirpj.2022.07.005 ↗
2. Herzog D, Seyda V, Wycisk E, Emmelmann C (2016) Additive manufacturing of metals. Acta Mater 117:371–39210.1016/j.actamat.2016.07.019 ↗
3. Ngo TD, Kashani A, Imbalzano G, Nguyen KTQ, Hui D (2018) Additive manufacturing (3D printing): a review of materials, methods, applications and challenges. Compos Part B Eng 143:172–19610.1016/j.compositesb.2018.02.012 ↗
4. Cai C, Zhou K (2022) Chapter 7: Metal additive manufacturing. In: Patel CD, Chen CH (eds) Digital manufacturing. Elsevier, Amsterdam, pp 247–29810.1016/B978-0-323-95062-6.00005-X ↗
5. Karthik GM, Kim HS (2021) Heterogeneous aspects of additive manufactured metallic parts: a review. Metals Mater Int 27(1):1–3910.1007/s12540-020-00931-2 ↗
6. Svetlizky D, Das M, Zheng B, Vyatskikh AL, Bose S, Bandyopadhyay A, Schoenung JM, Lavernia EJ, Eliaz N (2021) Directed energy deposition (DED) additive manufacturing: physical characteristics, defects, challenges and applications. Mater Today 49:271–29510.1016/j.mattod.2021.03.020 ↗
7. Guo L, Zhang L, Andersson J, Ojo O (2022) Additive manufacturing of 18% nickel maraging steels: defect, structure and mechanical properties: a review. J Mater Sci Technol 120:227–25210.1016/j.jmst.2021.10.056 ↗
8. DebRoy T, Wei HL, Zuback JS, Mukherjee T, Elmer JW, Milewski JO, Beese AM, Wilson-Heid A, De A, Zhang W (2018) Additive manufacturing of metallic components: process, structure and properties. Prog Mater Sci 92:112–22410.1016/j.pmatsci.2017.10.001 ↗
9. Tan C, Zhou K, Ma W, Zhang P, Liu M, Kuang T (2017) Microstructural evolution, nanoprecipitation behavior and mechanical properties of selective laser melted high-performance grade 300 maraging steel. Mater Des 134:23–3410.1016/j.matdes.2017.08.026 ↗
10. Roudnická M, Molnárová O, Dvorský D, Křivský L, Vojtěch D (2020) Specific response of additively manufactured AlSi9Cu3Fe alloy to precipitation strengthening. Metals Mater Int 26(8):1168–118110.1007/s12540-019-00504-y ↗
11. Conde FF, Avila JA, Oliveira JP, Schell N, Oliveira MF, Escobar JD (2021) Effect of the as-built microstructure on the martensite to austenite transformation in a 18Ni maraging steel after laser-based powder bed fusion. Addit Manuf 46:102122
12. Thompson SM, Bian L, Shamsaei N, Yadollahi A (2015) An overview of direct laser deposition for additive manufacturing; part I: transport phenomena, modeling and diagnostics. Addit Manuf 8:36–62
13. Tan C, Zhou K, Kuang M, Ma W, Kuang T (2018) Microstructural characterization and properties of selective laser melted maraging steel with different build directions. Sci Technol Adv Mater 19(1):746–75810.1080/14686996.2018.1527645 ↗
14. Fonseca D, Feitosa AM, Feitosa M, De Carvalho L, Lesley R, Padilha A (2021) A short review on ultra-high-strength maraging steels and future perspectives. Mater Res 24:20200470
15. Yao Y, Huang Y, Chen B, Tan C, Su Y, Feng J (2018) Influence of processing parameters and heat treatment on the mechanical properties of 18Ni300 manufactured by laser based directed energy deposition. Opt Laser Technol 105:171–17910.1016/j.optlastec.2018.03.011 ↗
16. Jägle EA, Sheng Z, Kürnsteiner P, Ocylok S, Weisheit AD (2017) Raabe comparison of maraging steel micro- and nanostructure produced conventionally and by laser additive manufacturing. Materials 10(1):8–2210.3390/ma10010008 ↗
17. Bodziak S, Al-Rubaie KS, Valentina LD, Lafratta FH, Santos EC, Zanatta AM, Chen Y (2019) Precipitation in 300 grade maraging steel built by selective laser melting: aging at 510 °C for 2 h. Mater Charact 151:73–8310.1016/j.matchar.2019.02.033 ↗
18. Bai Y, Wang D, Yang Y, Wang H (2019) Effect of heat treatment on the microstructure and mechanical properties of maraging steel by selective laser melting. Mater Sci Eng A 760:105–11710.1016/j.msea.2019.05.115 ↗
19. Casati R, Lemke JN, Tuissi A, Vedani M (2016) Aging behaviour and mechanical performance of 18-Ni 300 steel processed by selective laser melting. Metals 6(9):218–230. https://doi.org/10.3390/met609021810.3390/met6090218 ↗
20. Guo L, Zhang L, Andersson J, Ojo O (2024) Effect of heat treatment on mechanical compression properties of C250 maraging steel fabricated by directed energy deposition. Mater Charact 209:113778
21. Vasudevan VK, Kim SJ, Wayman CM (1990) Precipitation reactions and strengthening behavior in 18 Wt Pct nickel maraging steels. Metall trans A 21(10):2655–266810.1007/BF02646061 ↗
22. Xu X, Ganguly S, Ding J, Guo S, Williams S, Martina F (2018) Microstructural evolution and mechanical properties of maraging steel produced by wire+arc additive manufacture process. Mater Charact 143:152–16210.1016/j.matchar.2017.12.002 ↗
23. Rao MN (2006) Progress in understanding the metallurgy of 18% nickel maraging steels. Int J Mater Res 97(11):1594–160710.1515/ijmr-2006-0248 ↗
24. Strakosova A, Průša F, Michalcová A, Kratochvíl P, Vojtěch D (2022) Annealing response of additively manufactured high-strength 1.2709 maraging steel depending on elevated temperatures. Materials 15(11):3753–3764. https://doi.org/10.3390/ma1511375310.3390/ma15113753 ↗
25. Oliveira AR, Diaz JAA, Nizes ADC, Jardini AL, Del Conte EG (2021) Investigation of building orientation and aging on strength-stiffness performance of additively manufactured maraging steel. J Mater Eng Perform 30(2):1479–148910.1007/s11665-020-05414-4 ↗
26. Becker TH, Dimitrov D (2016) The achievable mechanical properties of SLM produced maraging steel 300 components. Rapid Prototyp J 22(3):487–49410.1108/RPJ-08-2014-0096 ↗
27. Suzuki A, Nishida R, Takata N, Kobashi M, Kato M (2019) Design of laser parameters for selectively laser melted maraging steel based on deposited energy density. Addit Manuf 28:160–168
28. Casalino G, Campanelli SL, Contuzzi N, Ludovico AD (2015) Experimental investigation and statistical optimisation of the selective laser melting process of a maraging steel. Opt Laser Technol 65:151–15810.1016/j.optlastec.2014.07.021 ↗
29. Rigon D, Meneghetti G, Görtler M, Cozzi D, Waldhauser W, Dabalà M (2018) Influence of defects on axial fatigue strength of maraging steel specimens produced by additive manufacturing. In: MATEC web of conferences, vol 165, p 02205. https://doi.org/10.1051/matecconf/20181650200510.1051/matecconf/201816502005 ↗
30. Mutua J, Nakata S, Onda T, Chen Z-C (2018) Optimization of selective laser melting parameters and influence of post heat treatment on microstructure and mechanical properties of maraging steel. Mater Des 139:486–49710.1016/j.matdes.2017.11.042 ↗
31. Bai Y, Yang Y, Wang D, Zhang M (2017) Influence mechanism of parameters process and mechanical properties evolution mechanism of maraging steel 300 by selective laser melting. Mater Sci Eng A 703:116–12310.1016/j.msea.2017.06.033 ↗
32. Zhou F, Wu R, Xie W, Zhang L (2020) Effect of aging treatment on microstructure and properties of additively manufactured maraging steel. Ironmak Steelmak 47(9):980–98510.1080/03019233.2019.1651022 ↗
33. Strakosova A, Kubásek J, Michalcová A, Průša F, Vojtěch D, Dvorský D (2019) High strength X3NiCoMoTi 18-9-5 maraging steel prepared by selective laser melting from atomized powder. Materials 12(24):4174–4183. https://doi.org/10.3390/ma1224417410.3390/ma12244174 ↗
34. Campanelli SL, Contuzzi N, Posa P, Angelastro A (2019) Study of the aging treatment on selective laser melted maraging 300 steel. Mater Res Express 6(6):06658010.1088/2053-1591/ab0c6e ↗
35. Hou H, Li H, Jin Y, Wang X, Wen Z (2014) Effect of heat treatment temperature on the mechanical properties of low-temperature high strength maraging steel. Mater Sci Eng A 601:1–610.1016/j.msea.2014.02.024 ↗
36. Mooney B, Kourousis KI, Raghavendra R, Agius D (2019) Process phenomena influencing the tensile and anisotropic characteristics of additively manufactured maraging steel. Mater Sci Eng A 745:115–12510.1016/j.msea.2018.12.070 ↗
37. Guo WF, Guo C, Zhu Q (2018) Heat treatment behavior of the 18Ni300 maraging steel additively manufactured by selective laser melting. Mater Sci Forum 941:2160–2166. https://doi.org/10.4028/www.scientific.net/MSF.941.216010.4028/www.scientific.net/MSF.941.2160 ↗
38. Kempen K, Yasa E, Thijs L, Kruth JP, Van Humbeeck J (2011) Microstructure and mechanical properties of selective laser melted 18Ni-300 steel. Phys Procedia 12:255–26310.1016/j.phpro.2011.03.033 ↗
39. Dehgahi S, Sanjari M, Ghoncheh MH, Amirkhiz BS, Mohammadi M (2021) Concurrent improvement of strength and ductility in heat-treated C300 maraging steels produced by laser powder bed fusion technique. Addit Manuf 39:101847
40. Tekin T, Ischia G, Naclerio F, Ipek R, Molinari A (2023) Effect of a direct aging heat treatment on the microstructure and the tensile properties of a 18Ni-300 maraging steel produced by laser powder bed fusion. Mater Sci Eng A 872:14492110.1016/j.msea.2023.144921 ↗
41. Amirabdollahian S, Deirmina F, Harris L, Siriki R, Pellizzari M, Bosetti P, Molinari A (2021) Towards controlling intrinsic heat treatment of maraging steel during laser directed energy deposition. Scr Mater 201:11397310.1016/j.scriptamat.2021.113973 ↗
42. Chen b, Huang Y, Gu T, Tan C, Feng J (2018) Investigation on the process and microstructure evolution during direct laser metal deposition of 18Ni300. Rapid Prototyp J 24(6):964–97210.1108/RPJ-01-2018-0022 ↗
43. Truong TD, Asala G, Ola OT, Ojo OA, Odeshi AG (2023) Texture and damage evolution in additively manufactured 18%Ni-M350 maraging steel under dynamic impact loading: processing parameters and heat treatment effects. Materialia 32:10196110.1016/j.mtla.2023.101961 ↗
44. Jeong J, No GW, Bae HJ, Yoo SK, Choi I-C, Kim HS, Seol JB, Kim JG (2024) Mechanical properties of lamellar-structured 18Ni300 maraging steel manufactured via directed energy deposition. Mater Sci Eng A 892:14603110.1016/j.msea.2023.146031 ↗
45. Asala G, Ola OT, Ojo OA (2023) Effects of process variables on the quality and mechanical properties of 18%Ni-M350 maraging steel produced by direct energy deposition laser additive manufacturing. Mater Sci Eng A 866:14464610.1016/j.msea.2023.144646 ↗
46. Deirmina F, Amirabdollahian S, Harris L, Bettini E, Siriki R, Pellizzari M, Bosetti P, Molinari A (2023) Laser-directed energy deposition of dissimilar maraging steels with a defect-free interface: design for improved surface hardness and fracture toughness. Metals Mater Int 29(10):2940–295410.1007/s12540-023-01424-8 ↗
47. Klinger M (2017) More features, more tools, more CrysTBox. J Appl Crystallogr 50(4):1226–1234. https://doi.org/10.1107/S160057671700679310.1107/S1600576717006793 ↗
48. Kassym K, Perveen A (2020) Atomization processes of metal powders for 3D printing. Mater Today Proc 26:1727–173310.1016/j.matpr.2020.02.364 ↗
49. Ren P, Ouyang Y, Mu J, Luo S, Tang Z, Wu Y, Leung CLA, Oliveira JP, Zou Y, Wang H, Wang H (2025) Metal powder atomization preparation, modification, and reuse for additive manufacturing: a review. Prog Mater Sci 152:10144910.1016/j.pmatsci.2025.101449 ↗
50. Nguyen HD, Pramanik A, Basak AK, Dong Y, Prakash C, Debnath S, Shankar S, Jawahir IS, Dixit S, Buddhi D (2022) A critical review on additive manufacturing of Ti–6Al–4V alloy: microstructure and mechanical properties. J Mater Res Technol 18:4641–466110.1016/j.jmrt.2022.04.055 ↗
51. Mullis AM, Farrell L, Cochrane RF, Adkins NJ (2013) Estimation of cooling rates during close-coupled gas atomization using secondary dendrite arm spacing measurement. Metall Mater Trans B 44(4):992–99910.1007/s11663-013-9856-2 ↗
52. Yin S, Chen C, Yan X, Feng X, Jenkins R, O’Reilly P, Liu M, Li H, Lupoi R (2018) The influence of aging temperature and aging time on the mechanical and tribological properties of selective laser melted maraging 18Ni-300 steel. Addit Manuf 22:592–600
53. Judas J, Tebib M, Sennour M, Delloro F, Zapletal J (2025) Microstructural evolution of AA7075 powder as feedstock material for cold spray deposition. Powder Technol 463:12116210.1016/j.powtec.2025.121162 ↗
54. Snell R, Tammas-Williams S, Chechik L, Lyle A, Hernández-Nava E, Boig C, Panoutsos G, Todd I (2020) Methods for rapid pore classification in metal additive manufacturing. JOM 72(1):101–10910.1007/s11837-019-03761-9 ↗
55. Liu S, Shin YC (2019) Additive manufacturing of Ti6Al4V alloy: a review. Mater Des 164:107552
56. Conde FF, Escobar JD, Oliveira JP, Jardini AL, Bose Filho WW, Avila JA (2019) Austenite reversion kinetics and stability during tempering of an additively manufactured maraging 300 steel. Addit Manuf 29:100804
57. Suryawanshi J, Prashanth KG, Ramamurty U (2017) Tensile, fracture, and fatigue crack growth properties of a 3D printed maraging steel through selective laser melting. J Alloys Compd 725:355–36410.1016/j.jallcom.2017.07.177 ↗
58. Revilla RI, Li G, Pion R, Marcoen K, Andreatta F, Fedrizzi L, Vanmeensel K, De Graeve I (2024) Effect of heat treatment on the microstructure and pitting corrosion behavior of 316L stainless steel fabricated by different additive manufacturing methods (L-PBF vs L-DED): comparative investigation exploring the role of microstructural features on passivity. Corros Sci 228:11181410.1016/j.corsci.2023.111814 ↗
59. Felicioni S, Aversa A, Librera E, Bondioli F, Fino P (2024) Directed energy deposition of 18NiM300 steel: effect of process and post processing conditions on microstructure and properties. Sci Technol Adv Mater 25(1):234607110.1080/14686996.2024.2346071 ↗
60. Magnee A, Drapier JM, Coutsouradi D, Habrakan L, Dumont J (1974) Cobalt-containing high-strength steels. INIS-MF--1971, Centre d'Information du Cobalt, Brussels. http://inis.iaea.org/Search/search.aspx?orig_q=RN:6217555
61. Silveira ACdF, Fechte-Heinen R, Epp J (2023) Microstructure evolution during laser-directed energy deposition of tool steel by in situ synchrotron X-ray diffraction. Addit Manuf 63:103408
62. Roudnická M, Vojtech D (2020) Fractography of additively manufactured titanium alloy: influence of post-processing treatment. Defect Diffus Forum 405:187–19210.4028/www.scientific.net/DDF.405.187 ↗
63. Deirmina F, Kearns M, Davies P, Harris L, Dixit N, Witte F, Casati R (2022) Effect of heat treatments on mechanical properties of ultra-high-strength maraging steels fabricated by additive manufacturing. In: Conference: AMPM2021: additive manufacturing with powder metallurgy conference. https://www.researchgate.net/publication/361666427
64. Turk C, Zunko H, Aumayr C, Leitner H, Kapp M (2019) Advances in maraging steels for additive manufacturing. BHM Berg-und Hüttenmännische Monatshefte 164(3):112–11610.1007/s00501-019-0835-z ↗
65. Deirmina F, Davies PA, Casati R (2022) Effects of powder atomization route and post-processing thermal treatments on the mechanical properties and fatigue resistance of additively manufactured 18Ni300 maraging steel. Adv Eng Mater 24(4):210101110.1002/adem.202101011 ↗
66. Strakosova A, Roudnická M, Šafka J, Ackermann M, Dvorský D, Školáková A, Vronka M, Svora P, Drahokoupil J, Pinc J, Maňák J, Ekrt O, Weiss Z, Mazáčová V, Lejček P (2024) Effect of titanium on microstructure and mechanical behaviour of additively manufactured 1.2709 maraging steel. Addit Manuf 88:104264
67. Król M, Snopiński P, Czech A (2020) The phase transitions in selective laser-melted 18-NI (300-grade) maraging steel. J Therm Anal Calorim 142(2):1011–101810.1007/s10973-020-09316-4 ↗
68. Reis AGd, Reis DAP, Abdalla AJ, Otubo J (2015) High-temperature creep resistance and effects on the austenite reversion and precipitation of 18 Ni (300) maraging steel. Mater Charact 107:350–35710.1016/j.matchar.2015.08.002 ↗
69. Zhang J, Xu X, Zhang S, Zhang L (2024) Effect of Si and P elements on the stability of Fe2Mo-laves phase in ferritic stainless steel. J Solid State Chem 339:124968
70. Xu TZ, Zhang S, Du Y, Wu CL, Zhang CH, Sun XY, Chen HT, Chen J (2024) Development and characterization of a novel maraging steel fabricated by laser additive manufacturing. Mater Sci Eng A 891:145975
71. Mooney B, Kourousis KI, Raghavendra R (2019) Plastic anisotropy of additively manufactured maraging steel: influence of the build orientation and heat treatments. Addit Manuf 25:19–31
72. Strakosova A, Roudnická M, Ekrt O, Vojtěch D, Michalcová A (2021) Hydrogen embrittlement of the additively manufactured high-strength X3NiCoMoTi 18-9-5 maraging steel. Materials 14(17):5073-5081. https://doi.org/10.3390/ma1417507310.3390/ma14175073 ↗
73. Stornelli G, Gaggia D, Rallini M, Di Schino A (2021) Heat treatment effect on maraging steel manufactured by laser powder bed fusion technology: microstructure and mechanical properties. Acta Metall Slovaca 27(3):122–12610.36547/ams.27.3.973 ↗
74. Huang F, Cheng Z, Zhang D, Qian D, Liu Y, Hu Z, Hua L (2024) A novel process for simultaneously improving the strength and plasticity of 18Ni(350) maraging steel. J Mater Res Technol 33:6144–615610.1016/j.jmrt.2024.10.242 ↗
75. Niu M, Zhou G, Wang W, Shahzad MB, Shan Y, Yang K (2019) Precipitate evolution and strengthening behavior during aging process in a 2.5 GPa grade maraging steel. Acta Mater 179:296–30710.1016/j.actamat.2019.08.042 ↗
76. Mukherjee T, Elmer JW, Wei HL, Lienert TJ, Zhang W, Kou S, DebRoy T (2023) Control of grain structure, phases, and defects in additive manufacturing of high-performance metallic components. Prog Mater Sci 138:10115310.1016/j.pmatsci.2023.101153 ↗