DataVXJournal of Materials SciencePaper
journal article·2024-07Open access

Role of Bi/Te co-dopants on the thermoelectric properties of SnSe polycrystals: an experimental and theoretical investigation

Manasa R. Shankar, A. N. Prabhu, Anuradha M. Ashok, Nithya Davis, Bhuvanesh Srinivasan, Vikash Mishra

Journal of Materials Science· Volume 59· Issue 28
Publisher pageOpen full text
Source abstract

Abstract

Abstract A sustainable solution to the energy crisis may be found in thermoelectric materials and generators, capable of transforming thermal energy into electrical energy or vice versa. SnSe is one of the emerging thermoelectric materials with distinctive properties. The main advantages of this compound are earth-abundant, inexpensive, non-toxic and it is also known for its high thermoelectric performance. Here we prepared Bi/Te co-doped SnSe polycrystals; whereas, Bi and Te are added with different compositions such as (x = 0.0,0.02,0.04,0.06 and y = 0.03) in (Sn1-xBixSe1-YTeY) matrix by using the solid-state reaction method. XRD data confirms the samples belong to the orthorhombic crystal system with the Pnma space group. DFT calculations were used to see structural stability and electronic properties for pure and doped SnSe samples. Temperature-dependent semiconducting behavior of the samples has been demonstrated by electrical resistivity. The Seebeck coefficient, correlated with carrier concentration and mobility, validates the p-type behavior for the pristine samples and the n-type behavior for co-doped samples. The dominant behavior of phonon scattering has been demonstrated by thermal conductivity analysis. After co-doping there is decrement in total thermal conductivity was observed which 1.3 times lower than SnSe. A theoretical calculation was used to validate experimental results to estimate electrical properties, Seebeck coefficient, specific heat capacity, thermal conductivity, and power factor using Quantum espresso code with Boltzmann transport Equation. 4% Bi-doped sample displayed a significant increment in electrical conductivity and an enhanced Seebeck coefficient, which led to the power factor enhancement of approximately 2.0 times in contrast to the pristine sample and enhanced ZT of about 0.055 which is 3.43 times higher than the pristine SnSe. Graphical abstract
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Thermoelectric Materials and Devices · Chalcogenide Semiconductor Thin Films · Phase-change materials and chalcogenides

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (74)

Show source-provided references
1. Yang Z, Liu J, Baskaran S et al (2010) Enabling renewable energy—and the future grid—with advanced electricity storage. JOM 62:14–23. https://doi.org/10.1007/s11837-010-0129-010.1007/s11837-010-0129-0 ↗
2. Ceyda Yelgel Ö, Srivastava GP (2013) Thermoelectric properties of p-type (Bi2Te3)x (Sb2Te3)1−x single crystals doped with 3 wt.% Te. J Appl Phys 113:073709. https://doi.org/10.1063/1.479265310.1063/1.4792653 ↗
3. Li W, Lin S, Zhang X, Chen Z, Xu X, Pei Y (2016) Thermoelectric properties of cu2snse4 with intrinsic vacancy. Chem Mater 28(17):6227–6232. https://doi.org/10.1021/acs.chemmater.6b0241610.1021/acs.chemmater.6b02416 ↗
4. Liang B, Song Z, Wang M, Wang L, Jiang W (2013) Fabrication and thermoelectric properties of graphene/Bi2Te3 composite materials. J Nanomater 2013:210767. https://doi.org/10.1155/2013/21076710.1155/2013/210767 ↗
5. Zhang Q et al (2015) Studies on thermoelectric properties of n-type polycrystalline SnSe1-xSx by iodine doping. Adv Energy Mater 5(12):1–8. https://doi.org/10.1002/aenm.20150036010.1002/aenm.201500360 ↗
6. Wei TR et al (2017) Thermoelectric transport properties of polycrystalline SnSe alloyed with PbSe. Appl Phys Lett 110:053901. https://doi.org/10.1063/1.497560310.1063/1.4975603 ↗
7. Feng D, Chen YX, Fu LW, Li J, He JQ (2018) SnSe+Ag2Se composite engineering with ball milling for enhanced thermoelectric performance. Rare Met 37(4):333–342. https://doi.org/10.1007/s12598-017-0994-610.1007/s12598-017-0994-6 ↗
8. Luo ZZ et al (2019) High figure of merit in gallium-doped nanostructured n-Type PbTe- xGeTe with midgap states. J Am Chem Soc 141(40):16169–16177. https://doi.org/10.1021/jacs.9b0924910.1021/jacs.9b09249 ↗
9. Chandra S, Bhat U, Dutta P, Bhardwaj A, Datta R, Biswas K (2022) Modular nanostructures facilitate low thermal conductivity and ultra-high thermoelectric performance in n-type SnSe. Adv Mater 34(40):1–9. https://doi.org/10.1002/adma.20220372510.1002/adma.202203725 ↗
10. Luo Y et al (2020) High-performance thermoelectrics from cellular nanostructured Sb2Si2Te6. Joule 4(1):159–175. https://doi.org/10.1016/j.joule.2019.10.01010.1016/j.joule.2019.10.010 ↗
11. Zhu Y et al (2022) Multiple valence bands convergence and strong phonon scattering lead to high thermoelectric performance in p-type PbSe. Nat Commun 13(1):1–9. https://doi.org/10.1038/s41467-022-31939-410.1038/s41467-022-31939-4 ↗
12. Sarkar D, Ghosh T, Banik A, Roychowdhury S, Sanyal D, Biswas K (2020) Highly converged valence bands and ultralow lattice thermal conductivity for high-performance SnTe thermoelectrics. Angew Chemie Int Ed 59(27):11115–11122. https://doi.org/10.1002/anie.20200394610.1002/anie.202003946 ↗
13. Zhou C et al (2018) Defect engineering for high-performance n-type PbSe thermoelectrics. J Am Chem Soc 140(29):9282–9290. https://doi.org/10.1021/jacs.8b0574110.1021/jacs.8b05741 ↗
14. Hodges JM et al (2018) Chemical insights into PbSe- x%HgSe: high power factor and improved thermoelectric performance by alloying with discordant atoms. J Am Chem Soc 140(51):18115–18123. https://doi.org/10.1021/jacs.8b1105010.1021/jacs.8b11050 ↗
15. Dutta M, Biswas RK, Pati SK, Biswas K (2021) Discordant Gd and electronic band flattening synergistically induce high thermoelectric performance in n-type PbTe. ACS Energy Lett 6(4):1625–1632. https://doi.org/10.1021/acsenergylett.1c0045010.1021/acsenergylett.1c00450 ↗
16. Ge B et al (2023) Engineering an atomic-level crystal lattice and electronic band structure for an extraordinarily high average thermoelectric figure of merit in n-type PbSe. Energy Environ Sci 16(9):3994–4008. https://doi.org/10.1039/d3ee01226c10.1039/d3ee01226c ↗
17. Ahmad A et al (2024) Largely enhanced thermoelectric performance in p-type Bi2Te3-based materials through entropy engineering. Energy Environ Sci 17(2):695–703. https://doi.org/10.1039/D3EE03720G10.1039/D3EE03720G ↗
18. Lee H et al (2023) Unique microstructures and high thermoelectric performance in n–type Bi2Te2.7Se0.3 by the dual incorporation of Cu and Y. Mater Today Phys 31:100986. https://doi.org/10.1016/j.mtphys.2023.10098610.1016/j.mtphys.2023.100986 ↗
19. Zhu B et al (2020) Realizing record high performance in n-type Bi2Te3-based thermoelectric materials. Energy Environ Sci 13(7):2106–2114. https://doi.org/10.1039/D0EE01349H10.1039/D0EE01349H ↗
20. Zhu T, Liu Y, Fu C, Heremans JP, Snyder JG, Zhao X (2017) Compromise and synergy in high-efficiency thermoelectric materials. Adv Mater 29:1605884. https://doi.org/10.1002/adma.20160588410.1002/adma.201605884 ↗
21. Ge B et al (2022) Atomic level defect structure engineering for unusually high average thermoelectric figure of merit in n-type PbSe rivalling PbTe. Adv Sci 9(35):1–14. https://doi.org/10.1002/advs.20220378210.1002/advs.202203782 ↗
22. Xu L et al (2022) Dense dislocations enable high-performance PbSe thermoelectric at low-medium temperatures. Nat Commun 13(1):1–10. https://doi.org/10.1038/s41467-022-34227-310.1038/s41467-022-34227-3 ↗
23. Luo ZZ et al (2021) Strong valence band convergence to enhance thermoelectric performance in PbSe with two chemically independent controls. Angew Chemie Int Edi 60(1):268–273. https://doi.org/10.1002/anie.20201176510.1002/anie.202011765 ↗
24. Zhou C et al (2020) Exceptionally high average power factor and thermoelectric figure of merit in n-type PbSe by the dual incorporation of Cu and Te. J Am Chem Soc 142(35):15172–15186. https://doi.org/10.1021/jacs.0c0771210.1021/jacs.0c07712 ↗
25. Xu P et al (2022) Dramatic enhancement of thermoelectric performance in PbTe by unconventional grain shrinking in the sintering process. Adv Mater 34(38):1–11. https://doi.org/10.1002/adma.20220294910.1002/adma.202202949 ↗
26. Luo ZZ et al (2022) Extraordinary role of Zn in enhancing thermoelectric performance of Ga-doped n-type PbTe. Energy Environ Sci 15(1):368–375. https://doi.org/10.1039/d1ee02986j10.1039/d1ee02986j ↗
27. Zhao LD et al (2012) Raising the thermoelectric performance of p-type Pbs with endotaxial nanostructuring and valence-band offset engineering using CdS and ZnS. J Am Chem Soc 134(39):16327–16336. https://doi.org/10.1021/ja306527n10.1021/ja306527n ↗
28. Jiang B et al (2020) Realizing high-efficiency power generation in low-cost PbS-based thermoelectric materials. Energy Environ Sci 13(2):579–591. https://doi.org/10.1039/c9ee03410b10.1039/c9ee03410b ↗
29. Singh NK, Bathula S, Gahtori B, Tyagi K, Haranath D, Dhar A (2016) The effect of doping on thermoelectric performance of p-type SnSe: promising thermoelectric material. J Alloys Compd 668:152–158. https://doi.org/10.1016/j.jallcom.2016.01.19010.1016/j.jallcom.2016.01.190 ↗
30. Chung I (2022) Recent advances in ultrahigh thermoelectric performance material SnSe. Mater Lab 1:1–9. https://doi.org/10.54227/mlab.2022005610.54227/mlab.20220056 ↗
31. Li Y, Shi X, Ren D, Chen J, Chen L (2015) Investigation of the anisotropic thermoelectric properties of oriented polycrystalline SnSe. Energies (Basel) 8(7):6275–6285. https://doi.org/10.3390/en807627510.3390/en8076275 ↗
32. Li S, Li X, Ren Z, Zhang Q (2018) Recent progress towards high performance of tin chalcogenide thermoelectric materials. J Mater Chem A Mater 6(6):2432–2448. https://doi.org/10.1039/c7ta09941j10.1039/c7ta09941j ↗
33. Zhao LD et al (2014) Ultralow thermal conductivity and high thermoelectric figure of merit in SnSe crystals. Nature 508(7496):373–377. https://doi.org/10.1038/nature1318410.1038/nature13184 ↗
34. Gao J, Zhu H, Mao T, Zhang L, Di J, Xu G (2017) The effect of Sm doping on the transport and thermoelectric properties of SnSe. Mater Res Bull 93:366–372. https://doi.org/10.1016/j.materresbull.2017.04.05310.1016/j.materresbull.2017.04.053 ↗
35. Chang C et al (1979) (2018) 3D charge and 2D phonon transports leading to high out-of-plane ZT in n-type SnSe crystals. Science 360(6390):778–783. https://doi.org/10.1126/science.aaq147910.1126/science.aaq1479 ↗
36. Chang C et al (2019) Realizing high-ranged out-of-plane ZTs in N-type SnSe crystals through promoting continuous phase transition. Adv Energy Mater 9(28):1–10. https://doi.org/10.1002/aenm.20190133410.1002/aenm.201901334 ↗
37. Lee YL et al (2022) Data-driven enhancement of ZT in SnSe-based thermoelectric systems. J Am Chem Soc 144(30):13748–13763. https://doi.org/10.1021/jacs.2c0474110.1021/jacs.2c04741 ↗
38. Ge ZH et al (2017) Boosting the thermoelectric performance of (Na, K)-codoped polycrystalline SnSe by synergistic tailoring of the band structure and atomic-scale defect phonon scattering. J Am Chem Soc 139(28):9714–9720. https://doi.org/10.1021/jacs.7b0533910.1021/jacs.7b05339 ↗
39. Zhou C et al (2018) High-performance n-Type PbSe-Cu2Se thermoelectrics through conduction band engineering and phonon softening. J Am Chem Soc 140(45):15535–15545. https://doi.org/10.1021/jacs.8b1044810.1021/jacs.8b10448 ↗
40. Lee YL et al (2023) TEXplorer.org: thermoelectric material properties data platform for experimental and first-principles calculation results. APL Mater 11:041111. https://doi.org/10.1063/5.013764210.1063/5.0137642 ↗
41. Zhao LD, Chang C, Tan G, Kanatzidis MG (2016) SnSe: a remarkable new thermoelectric material. Energy Environ Sci 9(10):3044–3060. https://doi.org/10.1039/c6ee01755j10.1039/c6ee01755j ↗
42. Zhou C et al (2021) Polycrystalline SnSe with a thermoelectric figure of merit greater than the single crystal. Nat Mater 20(10):1378–1384. https://doi.org/10.1038/s41563-021-01064-610.1038/s41563-021-01064-6 ↗
43. Kim T, Lee H, Chung I (2024) SnSe: The rise of the ultrahigh thermoelectric performance material. Bull Korean Chem Soc 45(3):186–199. https://doi.org/10.1002/bkcs.1282110.1002/bkcs.12821 ↗
44. Byun S et al (2024) Simultaneously engineering electronic and phonon band structures for high-performance n-type polycrystalline SnSe. Joule 8(5):1520–1538. https://doi.org/10.1016/j.joule.2024.02.01310.1016/j.joule.2024.02.013 ↗
45. Wei TR et al (2015) Thermoelectric transport properties of pristine and Na-doped SnSe1-xTex polycrystals. Phys Chem Chem Phys 17(44):30102–30109. https://doi.org/10.1039/c5cp05510e10.1039/c5cp05510e ↗
46. Sumanth A, Mishra V, Pandey P, Rao MSR, Dixit T (2022) Investigations into the role of native defects on photovoltaic and spintronic properties in copper oxide. IEEE Trans Nanotechnol 21:522–527. https://doi.org/10.1109/TNANO.2022.320458710.1109/TNANO.2022.3204587 ↗
47. Therese MJ, Mishra V, Rao MSR, Dixit T (2023) First-principles calculations to establish the functionality of self-connected point-defect migrations in n-ZnO-and p-CuO-based memristive devices. IEEE Trans Electron Devices 70(11):6026–6033. https://doi.org/10.1109/TED.2023.331700010.1109/TED.2023.3317000 ↗
48. Altomare A, Corriero N, Cuocci C, Falcicchio A, Moliterni A, Rizzi R (2015) EXPO software for solving crystal structures by powder diffraction data: methods and application. Cryst Res Technol 50(9–10):737–742. https://doi.org/10.1002/crat.20150002410.1002/crat.201500024 ↗
49. Deepika Shanubhogue U, Pal A, Rao A, Chattopadhyay S, Ashok AM, Davis N (2023) Tuning optical and thermoelectric properties of LaCoO3: partial substitution of La by isovalent Gd. J Alloys Compd 941:168987. https://doi.org/10.1016/j.jallcom.2023.16898710.1016/j.jallcom.2023.168987 ↗
50. Hegde GS, Prabhu AN, Rao A, Chattopadhyay MK (2021) Enhancement in thermoelectric figure of merit of bismuth telluride system due to tin and selenium co-doping. Mater Sci Semicond Process 127:105645. https://doi.org/10.1016/j.mssp.2020.10564510.1016/j.mssp.2020.105645 ↗
51. Mathew T, Kunjomana AG, Munirathnam K, Chandrasekharan KA, Meena M, Mahadevan CK (2012) Mechanical and dielectric properties of inte crystals. Crystal Struc Theory Appl 01(03):79–83. https://doi.org/10.4236/csta.2012.1301510.4236/csta.2012.13015 ↗
52. Das A et al (2021) Effect of iodine doping on the electrical, thermal and mechanical properties of SnSe for thermoelectric applications. Phys Chem Chem Phys 23(7):4230–4239. https://doi.org/10.1039/d0cp06130a10.1039/d0cp06130a ↗
53. Cai J et al (2020) Investigating the thermoelectric performance of n-type SnSe: The synergistic effect of NbCl5doping and dislocation engineering. J Mater Chem C Mater 8(38):13244–13252. https://doi.org/10.1039/d0tc02959a10.1039/d0tc02959a ↗
54. Zhao L et al (2015) The Effects of Te2− and I− substitutions on the electronic structures, thermoelectric performance, and hardness in melt-quenched highly dense Cu2-xSe. Adv Electron Mater 1(3):1–8. https://doi.org/10.1002/aelm.20140001510.1002/aelm.201400015 ↗
55. Mangavati S, Pal A, Rao A, Jiang ZZ, Kuo YK (2022) Reduction in low-temperature thermal conductivity of Cu2Se via substitution of Se by Te atoms. J Phys Chem Solids 160:110301. https://doi.org/10.1016/j.jpcs.2021.11030110.1016/j.jpcs.2021.110301 ↗
56. Sidharth D et al (2019) Enhancing effects of Te substitution on the thermoelectric power factor of nanostructured SnSe1-: XTex. Phys Chem Chem Phys 21(28):15725–15733. https://doi.org/10.1039/c9cp02018g10.1039/c9cp02018g ↗
57. Purushottam Bhat C et al (2023) Investigations on bi doped Cu2Se prepared by solid state reaction technique for thermoelectric applications. Energies (Basel) 16:3010. https://doi.org/10.3390/en1607301010.3390/en16073010 ↗
58. Li X et al (2018) N-type Bi-doped SnSe thermoelectric nanomaterials synthesized by a facile solution method. Inorg Chem 57(21):13800–13808. https://doi.org/10.1021/acs.inorgchem.8b0232410.1021/acs.inorgchem.8b02324 ↗
59. Shi X-L, Wu A-Y, Feng T, Zheng K, Liu W-D, Sun Q, Hong M, Pantelides ST, Chen Z-G, Zou J (2019) High thermoelectric performance in p-type polycrystalline Cd‐doped SnSe achieved by a combination of cation vacancies and localized lattice engineering. Adv Energy Mater 9:1803242. https://doi.org/10.1002/aenm.20180324210.1002/aenm.201803242 ↗
60. Tang Y et al (2018) High electrical transport properties performance enhanced by anti-site defects in single crystalline SnSe. J Alloys Compd 748:80–86. https://doi.org/10.1016/j.jallcom.2018.03.13510.1016/j.jallcom.2018.03.135 ↗
61. Pang J, Zhang X, Shen L, Xu J, Nie Y, Xiang G (2022) Synthesis and thermoelectric properties of Bi-doped SnSe thin films. Chin Phys B 30:116302. https://doi.org/10.1088/1674-1056/ac11da10.1088/1674-1056/ac11da ↗
62. Peng K et al (2016) Broad temperature plateau for high ZTs in heavily doped p-type SnSe single crystals. Energy Environ Sci 9(2):454–460. https://doi.org/10.1039/c5ee03366g10.1039/c5ee03366g ↗
63. Monikapani K, Vijay V, Abinaya R, Archana J, Harish S, Navaneethan M (2022) Realizing an enhanced seebeck coefficient and extremely low thermal conductivity in anharmonic Sb-substituted SnSe nanostructures. J Alloys Compd 923:165961. https://doi.org/10.1016/j.jallcom.2022.16596110.1016/j.jallcom.2022.165961 ↗
64. Gainza J et al (2020) High-performance n-type SnSe thermoelectric polyczrystal prepared by arc-melting. Cell Reports Phys Sci 1(12):100263. https://doi.org/10.1016/j.xcrp.2020.10026310.1016/j.xcrp.2020.100263 ↗
65. Duong AT et al (2016) Achieving ZT=2.2 with Bi-doped n-type SnSe single crystals. Nat Commun 7:1–6. https://doi.org/10.1038/ncomms1371310.1038/ncomms13713 ↗
66. Nguyen VQ et al (2018) Thermoelectric properties of hot-pressed bi-doped n-type polycrystalline SnSe. Nanoscale Res Lett 13:4–10. https://doi.org/10.1186/s11671-018-2500-y10.1186/s11671-018-2500-y ↗
67. Agne MT, Voorhees PW, Snyder GJ (2019) Phase transformation contributions to heat capacity and impact on thermal diffusivity, thermal conductivity, and thermoelectric performance. Adv Mater 31(35):1–7. https://doi.org/10.1002/adma.20190298010.1002/adma.201902980 ↗
68. Wang X et al (2015) Thermoelectric properties of Eu- and Na-substituted SnTe. J Rare Earths 33(11):1175–1181. https://doi.org/10.1016/S1002-0721(14)60543-310.1016/S1002-0721(14)60543-3 ↗
69. Gao J, Xu G (2017) Thermoelectric performance of polycrystalline Sn1-xCuxSe (x = 0–0.03) prepared by high pressure method. Intermetallics (Barking) 89:40–45. https://doi.org/10.1016/j.intermet.2017.05.01810.1016/j.intermet.2017.05.018 ↗
70. Wei W et al (2018) achieving high thermoelectric figure of merit in polycrystalline SnSe via introducing Sn vacancies. J Am Chem Soc 140(1):499–505. https://doi.org/10.1021/jacs.7b1187510.1021/jacs.7b11875 ↗
71. Liu W, Kim HS, Jie Q, Ren Z (2016) Importance of high power factor in thermoelectric materials for power generation application: a perspective. Scr Mater 111:3–9. https://doi.org/10.1016/j.scriptamat.2015.07.04510.1016/j.scriptamat.2015.07.045 ↗
72. Morales Ferreiro JO et al (2017) Effect of the annealing on the power factor of un-doped cold-pressed SnSe. Appl Therm Eng 111:1426–1432. https://doi.org/10.1016/j.applthermaleng.2016.07.19810.1016/j.applthermaleng.2016.07.198 ↗
73. Pandey S, Shukla A, Tripathi A (2022) Highly sensitive and self powered ultraviolet photo detector based on ZnO nanorods coated with TiO2. Sens Actuators A Phys 350:114112. https://doi.org/10.1016/j.sna.2022.11411210.1016/j.sna.2022.114112 ↗
74. Pandey S, Shukla A, Tripathi A (2022) Elucidating the influence of native defects on electrical and optical properties in semiconducting oxides: an experimental and theoretical investigation. Comput Mater Sci 210:111037. https://doi.org/10.1016/j.commatsci.2021.11103710.1016/j.commatsci.2021.111037 ↗