journal article·2025

DIESEL SPRAY CHARACTERISTICS OF MULTI-HOLE INJECTORS UNDER GEOMETRICAL SIMILARITY CONDITION

Yu Jin, Yifan Zhang, Pengbo Dong, Chang Zhai, Keiya Nishida, Yang Wang, Xianyin Leng

Atomization and Sprays· Volume 35· Issue 1
Publisher page

Abstract

Small-bore engines are popular due to low CO2 emissions and low fuel consumption. To simplify the design steps for various engine sizes, similarity theory was applied to engines. In this paper, the spray characteristics of non-evaporating sprays for multi-hole diesel injectors under the geometrical similarity condition were investigated by diffused background illumination (DBI). The similarity theory is based on Chikahisa theory, Wakuri momentum theory, and Inagaki analysis of geometrical similarity. Under the similarity condition, the injectors with hole diameters of 0.07, 0.101, and 0.133 mm were used at injection pressures of 45, 93, and 160 MPa, respectively. In addition, the injection pressure of 160 MPa was set as the same injection pressure condition for comparison. The results show that under the similarity condition and the same injection pressure conditions, spray tip penetration, spray angle, and other parameters follow the same trend of variation of hole diameters, except for the air-fuel ratio. The scaled spray tip penetration and the scaled spray cone angle (the angle at 30 times the hole diameters from the nozzle tip of the injector) of the three injectors under the similarity condition are well matched. However, for the injector with a hole diameter of 0.133 mm, the scaled spray angle (the angle at half of the spray tip penetration) is larger than others at the start of the injection, and the scaled air-fuel ratio is larger throughout the process. The difference in internal flow is responsible for the variation of the scaled spray parameters of the injector with 0.133 mm hole diameter compared to the others.
Source: openalex_inverted_index · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Combustion Engine Technologies · Aerodynamics and Fluid Dynamics Research · Vehicle emissions and performance

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. Arai, M., Interpretative Review of Diesel Spray Penetration Normalized by Length and Time of Breakup (Similarity Law of Diesel Spray and Its Application), Energies, vol. 15, no. 13, 4926, 2022.10.3390/en15134926 ↗
2. Arcoumanis, C., Flora, H., Gavaises, M., and Badami, M., Cavitation in Real-Size Multi-Hole Diesel Injector Nozzles, in SAE 2000 World Congress, SAE International, 2000.10.4271/2000-01-1249 ↗
3. Chen, H., Su, X., Li, J., and Zhong, X., Effects of Gasoline and Polyoxymethylene Dimethyl Ethers Blending in Diesel on the Combustion and Emission of a Common Rail Diesel Engine, Energy, vol. 171, pp. 981-999, 2019. DOI: 10.1016/j.energy.2019.01.08910.1016/j.energy.2019.01.089 ↗
4. Chen, Z., He, J., Chen, H., Geng, L., and Zhang, P., Comparative Study on the Combustion and Emissions of Dual-Fuel Common Rail Engines Fueled with Diesel/Methanol, Diesel/Ethanol, and Diesel/n-Butanol, Fuel, vol. 304, 121360, 2021. DOI: 10.1016/j.fuel.2021.12136010.1016/j.fuel.2021.121360 ↗
5. Chikahisa, T., Kikuta, K., and Murayama, T., Comparison of Experimental Results and Theoretical Prediction on Combustion Similarity for Differently Sized Diesel Engines, Nippon Kikai Gakkai Ronbunshu, B Hen/Trans. Jpn. Soc. Mech. Eng. Part B, vol. 59, no. 559, pp. 912-918, 1993.10.1299/kikaib.59.912 ↗
6. Chikahisa, T. and Murayama, T., Theory on Combustion Similarity for Different-Sized Diesel Engines, JSME International Journal, Series 2: Fluids Engineering, Heat Transfer, Power, Combustion, Thermophys. Prop., vol. 33, no. 2, pp. 395-400, 1990. DOI: 10.1299/jsmeb1988.33.2_39510.1299/jsmeb1988.33.2_395 ↗
7. Chilumukuru, K., Gupta, A., Ruth, M., Cunningham, M., Kothandaraman, G., Cumaranatunge, L., and Hess, H., Aftertreatment Architecture and Control Methodologies for Future Light Duty Diesel Emission Regulations, SAE Int. J. Engine, vol. 10, no. 4, pp. 1580-1587, 2017. DOI: 10.4271/2017-01-091110.4271/2017-01-0911 ↗
8. Djamari, D.W., Idris, M., Paristiawan, P.A., Abbas, M.M., Samuel, O.D., Soudagar, M.E.M., Herawan, S.G., Chandran, D., Yusuf, A.A., Panchal, H., and Veza, I., Diesel Spray: Development of Spray in Diesel Engine, Sustainability, vol. 14, no. 23, 15902, 2022.10.3390/su142315902 ↗
9. Emberson, D.R., Ihracska, B., Imran, S., and Diez, A., Optical Characterization of Diesel and Water Emulsion Fuel Injection Sprays Using Shadowgraphy, Fuel, vol. 172, pp. 253-262, 2016. DOI: 10.1016/j. fuel.2016.01.01510.1016/j.fuel.2016.01.015 ↗
10. Fansler, T.D. and Parrish, S.E., Spray Measurement Technology: A Review, Meas. Sci. Technol., vol. 26, no. 1, p. 12002. DOI: 10.1088/0957-0233/26/1/01200210.1088/0957-0233/26/1/012002 ↗
11. Giraldo, J., Payri, R., Marti Aldaravi, P., and Montiel, T., Effect of High Injection Pressures and Ambient Gas Properties over the Macroscopic Characteristics of the Diesel Spray on Multi-Hole Nozzles, Atomiz. Sprays, vol. 28, no. 12, pp. 1145-1160, 2018.10.1615/AtomizSpr.2019029651 ↗
12. He, Z., Shao, Z., Wang, Q., Zhong, W., and Tao, X., Experimental Study of Cavitating Flow inside Vertical Multi-Hole Nozzles with Different Length-Diameter Ratios Using Diesel and Biodiesel, Exp. Therm. Fluid Sci., vol. 60, pp. 252-262, 2015. DOI: 10.1016/j.expthermflusci.2014.09.01510.1016/j.expthermflusci.2014.09.015 ↗
13. He, Z., Zhang, Z., Guo, G., Wang, Q., Leng, X., and Sun, S., Visual Experiment of Transient Cavitating Flow Characteristics in the Real-Size Diesel Injector Nozzle, Int. J. Commun. Heat Mass Transf,, vol. 78, pp. 13-20, 2016. DOI: 10.1016/j.icheatmasstransfer.2016.08.00410.1016/j.icheatmasstransfer.2016.08.004 ↗
14. He, Z., Zhong, W., Wang, Q., Jiang, Z., and Fu, Y., An Investigation of Transient Nature of the Cavitating Flow in Injector Nozzles, Appl. Therm. Eng., vol. 54, no. 1, pp. 56-64, 2013. DOI: 10.1016/j.applthermaleng.2013.01.02410.1016/j.applthermaleng.2013.01.024 ↗
15. Hiroyasu, H., and Arai, M., Structures of Fuel Sprays in Diesel Engines, in Intl. Congress & Exposition, SAE International, 1990.10.4271/900475 ↗
16. Hu, B., He, Z., Li, C., Deng, Y., Guan, W., Zhang, L., and Guo, G., Study of the Effect of Cavitation Flow Patterns in Diesel Injector Nozzles on Near-Field Spray Atomization Characteristics Using a LES-VOF Method, Int. J. Multiph. Flow, vol. 174, 104791, 2024. DOI: 10.1016/j.ijmultiphaseflow.2024.10479110.1016/j.ijmultiphaseflow.2024.104791 ↗
17. Inagaki, K., Mizuta, J., Kawamura, K., Idota, Y., and Hashizume, T., Theoretical Study on Spray Design for Small-Bore Diesel Engine, SAE Technical Papers, SAE Int., vol. 2016, 2016.10.4271/2016-01-0740 ↗
18. Jin, Y., Dong, P., Zhai, C., Nishida, K., Ogata, Y. and Leng, X., Internal Flow and Spray Characterization of Multi-Hole Injectors: Comparison with Single-Hole Injectors, Energy Fuels, vol. 34, no. 6, pp. 7490-7501, 2020a. DOI: 10.1021/acs.energyfuels.0c0047310.1021/acs.energyfuels.0c00473 ↗
19. Jin, Y., Zhai C., Nishida K., and Ogata Y., An Analysis of Diesel Spray Characteristics with Small Injection Amount under Similarity Law Condition, in Small Engine Technology Conf. & Exposition, Society of Automotive Engineers of Japan, 2020b.10.4271/2019-32-0590 ↗
20. Kim, J., Kakami, S., Jin, Y., Nishida, K., and Ogata, Y., Internal Fuel Flow, Near-Field and Far-Field Spray Evolution, and Mixture Formation Characteristics of Diesel Injectors - A Comparison between Multiand Single-Hole Injectors, SAE Technical Papers, SAE International, vol. 2019-April, no. April, 2019.10.4271/2019-01-0273 ↗
21. Liang, X., Wang, Y., Chen, Y., and Deng, S., Advances in Emission Regulations and Emission Control Technologies for Internal Combustion Engines, Int. J. Sustain. Transp. Energy Environ. Policy, vol. 2, no. 2, pp. 101-119, 2021. DOI: 10.4271/13-02-02-000710.4271/13-02-02-0007 ↗
22. Liu, R., Huang, L., Ma, Y., Ju, D., Feng, M., and Lu, X., Schlieren and Mie-Scattering Visualization of an Evaporating Spray under Marine Diesel Engine Conditions, Proc. Inst. Mech. Eng. Pt. A: J. Power Energy, vol. 237, no. 5, pp. 1014-1027, 2023. DOI: 10.1177/0957650923115252210.1177/09576509231152522 ↗
23. Liu, Y., Li, F., Fu, W., Jiang, X., Song, Z., Zhu, Z., and Lin, Q., Experimental Investigation of Effects of Di-
24. N-Butyl Ether Addition on Spray Macroscopic Characteristics of Diesel-Biodiesel Blends, J. Energy Eng., vol. 145, no. 6, 04019028, 2019. DOI: 10.1061/(asce)ey.1943-7897.000063010.1061/(ASCE)EY.1943-7897.0000630 ↗
25. Mohan, B., Yang, W., Tay, K.L., and Yu, W., Macroscopic Spray Characterization under High Ambient Density Conditions, Exp. Therm. Fluid Sci., vol. 59, pp. 109-117, 2014. DOI: 10.1016/j.expthermflusci.2014.08.00310.1016/j.expthermflusci.2014.08.003 ↗
26. Niklawy, W., Shahin, M., Amin, M.I., and Elmaihy, A., Modelling and Experimental Investigation of High - Pressure Common Rail Diesel Injection System, in IOP Conf. Series: Materials Science and Engineering, IOP Publishing Ltd., vol. 973, no. 1, 2020.10.1088/1757-899X/973/1/012037 ↗
27. Nishida, K., Gao, J., Manabe, T., and Zhang, Y., Spray and Mixture Properties of Evaporating Fuel Spray Injected by Hole-Type Direct Injection Diesel Injector, Int. J. Engine Res., vol. 9, no. 4, pp. 347-360, 2008. DOI: 10.1243/14680874JER0050810.1243/14680874JER00508 ↗
28. Park, S.H., Kim, H.J., and Lee, C.S., Effect of Multiple Injection Strategies on Combustion and Emission Characteristics in a Diesel Engine, Energy Fuels, vol. 30, no. 2, pp. 810-818, 2016. DOI: 10.1021/acs. energyfuels.5b02121
29. Park, S.H., Suh, H.K., and Lee, C.S., Effect of Cavitating Flow on the Flow and Fuel Atomization Characteristics of Biodiesel and Diesel Fuels, Energy Fuels, vol. 22, no. 1, pp. 605-613, 2008. DOI: 10.1021/ef700330510.1021/ef7003305 ↗
30. Payri, R., Salvador, F.J., Bracho, G., and Viera, A., Differences between Single and Double-Pass Schlieren Imaging on Diesel Vapor Spray Characteristics, Appl. Therm. Eng., vol. 125, pp. 220-231, 2017. DOI: 10.1016/j.applthermaleng.2017.06.14010.1016/j.applthermaleng.2017.06.140 ↗
31. Pickett, L.M., Siebers, D.L., and Idicheria, C.A., Relationship Between Ignition Processes and the Lift-Off Length of Diesel Fuel Jets, Powertrain & Fluid Systems Conference & Exhibition, SAE International, 2005.10.4271/2005-01-3843 ↗
32. Qi, D.H., Ding, X.Q., Zhao, W.B., and Yang, K., Spray Characteristics and Engine Performance of Vegetable Oil-Diesel-Ethanol Hybrid Fuel, 2019. DOI: 10.1061/(ASCE)EY.194310.1061/(ASCE)EY.1943-7897.0000606 ↗
33. Safiullah, Nishida, K., Ogata, Y., Oda, T., and Ohsawa, K., Effects of Nozzle Hole Size and Rail Pressure on Diesel Spray and Mixture Characteristics under Similar Injection Rate Profile - Experimental, Computational and Analytical Studies under Non-Evaporating Spray Condition, Proc. Inst. Mech. Eng. Pt. D J. Automobile Eng., vol. 236, nos. 2-3, pp. 310-321, 2022. DOI: 10.1177/0954407021102209910.1177/09544070211022099 ↗
34. Shi, Y., and Reitz, R.D., Study of Diesel Engine Size-Scaling Relationships Based on Turbulence and Chemistry Scales, in SAE World Congress & Exhibition, SAE International, 2008.10.4271/2008-01-0955 ↗
35. Stager, L.A., and Reitz, R.D., Assessment of Diesel Engine Size-Scaling Relationships, in SAE World Congress & Exhibition, SAE International, 2007.10.4271/2007-01-0127 ↗
36. Suh, H.K. and Lee, C., Effect of Cavitation in Nozzle Orifice on the Diesel Fuel Atomization Characteristics, Int. J. Heat Fluid Flow, vol. 29, no. 4, pp. 1001-1009, 2008. DOI: 10.1016/j.ijheatfluidflow.2008.03.01410.1016/j.ijheatfluidflow.2008.03.014 ↗
37. Tang, X., Wang, P., Zhang, Z., Zhang, F., Shi, L., and Deng, K., Effects of High-Pressure and Donor-Cylinder Exhaust Gas Recirculation on Fuel Economy and Emissions of Marine Diesel Engines, Fuel, vol. 309, 2022. DOI: 10.1016/j.fuel.2021.12222610.1016/j.fuel.2021.122226 ↗
38. Wakuri, Y., Fujii, M., Amitani, T., And Tsuneya, R., Studies on the Penetration of Fuel Spray of Diesel Engine, Trans. Jpn. Soc. Mech. Eng., vol. 25, no. 156, pp. 820-826, 1959. DOI: 10.1299/kikai1938.25.82010.1299/kikai1938.25.820 ↗
39. Yamauchi, J., Dong, PengBo, Nishida, K., and Ogat, Y., Effects of Hole Diameter and Injection Pressure on Fuel Spray and Its Evaporation Characteristics of Multi-Hole Nozzle for Diesel Engine, in Intl. Powertrains, Fuels & Lubricants Meeting, SAE International, 2017.10.4271/2017-01-2305 ↗
40. Yin, B., Yu, S., Jia, H., and Yu, J., Numerical Research of Diesel Spray and Atomization Coupled Cavitation by Large Eddy Simulation (LES) under High Injection Pressure, Int. J. Heat Fluid Flow, vol. 59, pp. 1-9, 2016. DOI: 10.1016/j.ijheatfluidflow.2016.01.00510.1016/j.ijheatfluidflow.2016.01.005 ↗
41. Zhai, C., Jin, Y., Nishida, K., and Ogata, Y., Diesel Spray and Combustion of Multi-Hole Injectors with Micro-Hole under Ultra-High Injection Pressure - Non-Evaporating Spray Characteristics, Fuel, vol. 283, 2021. DOI: 10.1016/j.fuel.2020.11932210.1016/j.fuel.2020.119322 ↗
42. Zhao, J., Grekhov, L., Ma, X., and Denisov, A., Specific Features of Diesel Fuel Supply under Ultra-High Pressure, Appl. Therm. Eng., vol. 179, 2020. DOI: 10.1016/j.applthermaleng.2020.11569910.1016/j.applthermaleng.2020.115699 ↗
43. Zhou, X., Li, T., Lai, Z., and Huang, S., Similarity of Split-Injected Fuel Sprays for Different Size Diesel Engines, Int. J. Engine Res., vol. 22, no. 3, pp. 1028-1044, 2021b. DOI: 10.1177/146808741984977110.1177/1468087419849771 ↗
44. Zhou, X., Li, T., Lai, Z., and Wang, B., Scaling Fuel Sprays for Different Size Diesel Engines, Fuel, vol. 225, pp. 358-369, 2018a. DOI: 10.1016/j.fuel.2018.03.16710.1016/j.fuel.2018.03.167 ↗
45. Zhou, X., Li, T., Lai, Z., and Wang, B., Theoretical Study on Similarity of Diesel Combustion, SAE Technical Papers, SAE International, vol. 2018, 2018b.10.4271/2018-01-0235 ↗
46. Zhou, X., Li, T., Wei, Y., and Wang, N., Scaling Liquid Penetration in Evaporating Sprays for Different Size Diesel Engines, Int. J. Engine Res., vol. 21, no. 9, pp. 1662-1677, 2020. DOI: 10.1177/146808741988983510.1177/1468087419889835 ↗
47. Zhou, X., Li, T., and Yi, P., The Similarity Ratio Effects in Design of Scaled Model Experiments for Marine Diesel Engines, Energy, vol. 231, 2021b. DOI: 10.1016/j.energy.2021.12111610.1016/j.energy.2021.121116 ↗