Effect of He and N2 gas on the mechanical and tribological assessment of SS316L coating deposited by cold spraying process
Source abstract
Abstract
Abstract In this study, simulation and experimental methods were used to investigate the influence of cold spray conditions on AISI 316L stainless steel coatings. The effect of both helium and nitrogen gases used was investigated. The temperature, particle sizes of spraying powder, and distance from the nozzle throat to the impinging point were estimated by using the Kinetics Spray Solutions GmbH software. The 316L stainless steel (SS) coatings were examined by X-ray diffraction, Scanning Electron Microscopy and Energy Dispersive X-Ray Microanalysis. The tribological behavior was evaluated under different loads (2 N and 5 N) in dry conditions. It was found that the nitrogen and helium propellant gas with high speed and fine particles led to produce good coatings with dense microstructures. From the nanoindentation experiments, the Young's modulus and hardness of the SS 316L samples were enhanced of about 8% with helium due to the high particle velocity. It was shown that the wear resistance of SS 316L produced with helium was higher than that of the standard SS 316L coatings. The coatings produced with helium revealed lower friction coefficient (0.65) and wear rate (6.9 × 10–4 mm3/Nm) under 2 N applied load than that obtained nitrogen. It was also found that the SS 316L cold sprayed by helium with dense structure presents high hardness and good tribological performance that can be suggested for several applications. Graphical Abstract
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (63)
Show source-provided references
1. Singh H, Sidhu TS, Kalsi SBS, Karthikeyan J (2013) Development of cold spray from innovation to emerging future coating technology. Braz Soc Mech Sci Eng 35:231–24510.1007/s40430-013-0030-1 ↗
2. Irissou E, Legoux JG, Ryabinin AN, Jodoin B, Moreau C (2008) Review on cold spray process and technology: part I-intellectual property. Therm Spray Technol 17(4):495–51610.1007/s11666-008-9203-3 ↗
3. Singh H, Sidhu TS, Kalsi SBS, Karthikeyan J (2012) Cold spray technology: future of coating deposition processes. Fratturaed Integrità Strutturale 22:69–8410.3221/IGF-ESIS.22.08 ↗
4. Bala N, Singh H, Karthikeyan J, Prakash S (2014) Cold spray coating process for corrosion protection: a review. Surf Eng 30(6):414–42110.1179/1743294413Y.0000000148 ↗
5. Ogawa K (2017) Cold spray coatings. Vacuum Society of Japan 60(5):187–19210.3131/jvsj2.60.187 ↗
6. Oyinbo ST, Jen TC (2020) Molecular dynamics investigation of temperature effect and surface configurations on multiple impacts plastic deformation in a palladium-copper composite metal membrane (CMM): A cold gas dynamic spray (CGDS) process. Comput Mater Sci 185:10996810.1016/j.commatsci.2020.109968 ↗
7. Karthikeyan J (2004) Cold spray technology: international status and USA efforts. OH, ASB Industries Inc, Barberton, pp 1–14
8. Yoon S, Kim H, Lee C (2007) Fabrication of automotive heat exchanger using kinetic spraying process. Surf Coat Technol 201(24):9524–953210.1016/j.surfcoat.2007.04.026 ↗
9. Cizek J, Kovarik O, Siska F, Bensch J, Cupera J, Matejkova M, Siegl J, Chraska T, Kho KA (2019) Increasing fatigue endurance of hydroxyapatite and rutile plasma sprayed biocomponents by controlling deposition in-flight properties. ACS Biomater Sci Eng 5:1703–171410.1021/acsbiomaterials.8b01545 ↗
10. Goldbaum D, Shockley JM, Chromik R, Rezaeian A, Yue S, Legoux JG, Irissou E (2012) The Effect of deposition conditions on adhesion strength of Ti and Ti6Al4V cold spray splats. Thermal Spray Technol 21(2):288–30310.1007/s11666-011-9720-3 ↗
11. Rech S, Trentin A, Vezzu S, Legoux JG, Irissou E, Guagliano M (2011) Influence of pre-heated Al 6061 substrate temperature on the residual stresses of multipass Al coatings deposited by cold spray. Thermal Spray Technol 20(1–2):243–25110.1007/s11666-010-9596-7 ↗
12. Champagne VK, Helfritch D, Leyman P, Grendahl S, Klotz B (2005) Interface material mixing formed by the deposition of copper on aluminum by means of the cold spray process. ThermSpray Tech 14:330–334
13. Ajdelsztajn L, E.B. jodoin, G. Kim, J.M. Schoenung, (2005) Cold spray deposition of nanocrystalline aluminum alloys. Metal Mater Tran A 36A:657–66610.1007/s11661-005-0182-4 ↗
14. Bagherifard S, Astaraee AH, Locati M, Nawaz A, Monti S, Kondas J, Singh R, Guagliano M (2020) Design and analysis of additive manufactured bimodal structures obtained by cold spray deposition. Additive Manufact 33:10113110.1016/j.addma.2020.101131 ↗
15. Assadi H, Kreye H, Gartner F, Klassen T (2016) Cold spraying - A materials perspective. Acta Mater 116:382–40710.1016/j.actamat.2016.06.034 ↗
16. Adachi S, Ueda N (2017) Effect of cold-spray conditions using a nitrogen propellant gas on AISI 316L stainless steel-coating microstructures. Coatings 87(7):1–9
17. Moridi A, Hassani-Gangaraj SM, Guagliano M, Dao M (2014) Cold spray coating: review of material systems and future perspectives. Surf Eng 30:369–39510.1179/1743294414Y.0000000270 ↗
18. Grigoriev S, Okunkova A, Sova A, Bertrand P, Smurov I (2015) Cold spraying: from process fundamentals towards advanced applications. Surf Coat Technol 268:77–8410.1016/j.surfcoat.2014.09.060 ↗
19. Kay Charles M, Karthikeyan J (eds) (2016) High pressure cold spray: principles and applications. ASM International. https://doi.org/10.31399/asm.tb.hpcspa.978162708285310.31399/asm.tb.hpcspa.9781627082853 ↗
20. Moridi A, Hassani-Gangaraj SM, Guagliano M (2013) A hybrid approach to determine criticaland erosion velocities in the cold spray process. Appl Surf Sci 273:617–62410.1016/j.apsusc.2013.02.089 ↗
21. Mangour BAL, Vo P, Mongrain R, Irissou E, Yue S (2014) Effect of heat treatment on the microstructure and mechanical properties of stainless steel 316l coatings produced by cold spray for biomedical applications. Therm Spray Technol 23:641–65210.1007/s11666-013-0053-2 ↗
22. Dikici B, Yilmazer H, Ozdemir I, Isik M (2016) The effect of post-heat treatment on microstructure of 316L cold-sprayed coatings and their corrosion performance. J Therm Spray Tech 25(4):704–71410.1007/s11666-016-0402-z ↗
23. Dewidar MM, Khalil KA, Lim JK (2007) Processing and mechanical properties of porous 316L stainless steel for biomedical applications. Trans Nonferrous Metals Soc China 17(3):468–47310.1016/S1003-6326(07)60117-4 ↗
24. Villa M, Dosta S, Guilemany JM (2013) Optimization of 316L stainless steel coatings on light alloys using cold gas spray. Surf Coat Technol 235:220–22510.1016/j.surfcoat.2013.07.036 ↗
25. Li WY, Liao H, Douchy G, Coddet C (2007) Optimal design of a cold spray nozzle by numerical analysis of particle velocity and experimental validation with 316L stainless steel powder. Mater Des 28(7):2129–213710.1016/j.matdes.2006.05.016 ↗
26. Maestracci R, Sova A, Jeandin M, Malhaire JM, Movchan I, Bertrand P, Smurov I (2016) Deposition of composite coatings by cold spray using stainless steel 316L, copper and tribaloy T-700 powder mixtures. Surf Coat Technol 287(1):1–810.1016/j.surfcoat.2015.12.065 ↗
27. Chen J, Ma B, Liu G, Song H, Wu J, Cui L, Zheng Z (2017) Wear and corrosion properties of316l-SiC composite coating deposited by cold spray on magnesium alloy. Therm Spray Tech 26:1381–139210.1007/s11666-017-0583-0 ↗
28. Villa M, Dosta S, Guilemany JM (2013) Optimization of 316L stainless steel coatings on lightalloys using Cold Gas Spray. Surf Coat Technol 235:220–22510.1016/j.surfcoat.2013.07.036 ↗
29. Che H, Vo P, Yue S (2019) Investigation of cold spray on polymers by single particle impact experiments. Therm Spray Tech 28:135–14310.1007/s11666-018-0801-4 ↗
30. Schmidt T, Assadi H, Gärtner F, Richter H, Stoltenhoff T, Kreye H, Klassen T (2009) From particle acceleration to impact and bonding in cold spraying. J Therm Spray Tech 18:794. https://doi.org/10.1007/s11666-009-9357-710.1007/s11666-009-9357-7 ↗
31. Oliver WC, Pharr GM (1992) An improved technique for determining hardness and elasticmodulus. Mater Res 7:1564–158310.1557/JMR.1992.1564 ↗
32. Papyrin A (2001) Cold spray technology. Adv Mater Process 159:49–51
33. Li WY, Li CJ (2005) Optimal design of a novel cold spray gun nozzle at a limited space. J Therm Spray Technol 14(3):391–39610.1361/105996305X59404 ↗
34. Liebersbach P, Foelsche A, Champagne VK, Siopis M, Nardi A, Schmidt DP (2020) CFD simulations of feeder tube pressure oscillations and prediction of clogging in cold spray nozzles. J Therm Spray Technol 29(3):400–412. https://doi.org/10.1007/s11666-020-00992-010.1007/s11666-020-00992-0 ↗
35. Katanoda H, Fukuhara M, Iino N (2007) Numerical study of combination parameters for particle impact velocity and temperature in cold spray. J Therm Spray Technol 16(5–6):627–63310.1007/s11666-007-9087-7 ↗
36. Stoltenhoff T, Kreye H, Richter HJ (2002) An analysis of the cold spray process and its coatings. J Therm Spray Technol 11:542–55010.1361/105996302770348682 ↗
37. Gilmore DL, Dykhuizen RC, Neiser RA, Roemer TJ, Smith MF (1999) Particle velocity and deposition efficiency in the cold spray process. J Thermal Spray Technol 8:576–58210.1361/105996399770350278 ↗
38. Jodoin B (2002) Cold spray nozzle mach number limitation. J Thermal Spray Technol 1:496–50710.1361/105996302770348628 ↗
39. Venkatesh L, Chavan NM, Sundararajan G (2011) The influence of powder particle velocity and microstructure on the properties of cold sprayed copper coatings. J Thermal Spray Technol 20(5):1009–1021. https://doi.org/10.1007/s11666-011-9614-410.1007/s11666-011-9614-4 ↗
40. Alkhimov AP, Kosarev VF, Klinkov SV (2001) The features of cold spray nozzle design. J Thermal Spray Technol 10(2):375–38110.1361/105996301770349466 ↗
41. Sova A, Grigoriev S, Okunkova A, Smurov I (2013) Cold spray deposition of 316L stainless steel coatings on aluminium surface with following laser post-treatment. Surf Coat Technol 235:283–28910.1016/j.surfcoat.2013.07.052 ↗
42. Amiri M, Crawford GA, Earthman JC (2021) Quantitative percussion diagnostics for evaluating porosity and surface roughness of cold sprayed and laser deposited materials. J Market Res 14:312–323
43. Champagne VK (2007) The cold spray materials deposition process: fundamentals and applications. Woodhead Publishing Ltd., England
44. Venkatesh L, Chavan NM, Sundararajan G (2011) The influence of powder particle velocity and microstructure on the properties of cold sprayed copper coatings. Therm Spray Tech 20(5):1009–102110.1007/s11666-011-9614-4 ↗
45. Borchers C, Schmidt T, Gärtner F, Kreye H (2008) High strain rate deformation microstructures of stainless steel 316L by cold spraying and explosive powder compaction. Appl Phys A 90:517–52610.1007/s00339-007-4314-0 ↗
46. Coddet P, Verdy C, Coddet C, Debray F, Lecouturier F (2015) Mechanical properties of thick304L stainless steel deposits processed by He cold spray. Surf Coat Technol 277(15):74–8010.1016/j.surfcoat.2015.07.001 ↗
47. Duru E, Doğan F, Uysal M, Akbulut H, Aslan S (2021) Fabrication and characterization of graphene oxide reinforced NiB composite coating by pulsed electrodeposition technique. Diamond Related Mater 120:10868810.1016/j.diamond.2021.108688 ↗
48. Aslan S, Duru E (2021) Microstructure and wear properties of electrodeposited Ni-B-Al2O3 composite coating on low carbon steel at elevated temperature. J of Materi Eng and Perform. https://doi.org/10.1007/s11665-021-06290-210.1007/s11665-021-06290-2 ↗
49. Gültekin D, Duru E, Akbulut H (2021) Improved wear behaviors of lead-free electroless NiB and Ni-B/CeO2 composite coatings. Surf and Coat Technol 422:12752510.1016/j.surfcoat.2021.127525 ↗
50. Duru E, Dogan F, Uysal M, Akbulut H, Aslan S (2021) Optimization of Ni-B coating bath and effect of DMAB concentration on hardness and wear. Surf and Interfaces 22:10088010.1016/j.surfin.2020.100880 ↗
51. Jia YF, Cui YY, Xuan FZ, Yang F (2017) Comparison between single loading–unloading indentation and continuous stiffness indentation. RSC Adv 7:35655–3566510.1039/C7RA06491H ↗
52. Li RW, Zhang Z, Li JW, Ma KX, Guo YY, Zhou YW, Wu FY (2020) Surface modification of 316L stainless steel by diamond-like carbon films. J Iron Steel Res Int 27:867–87410.1007/s42243-020-00409-w ↗
53. Aissani L, Alhussein A, Nouveau C, Ghelani L, Zaabat M (2019) Influence of film thickness and Ar-N2 plasma gas on the structure and performance of sputtered vanadium nitride coatings. Surface Coatings Technol 378:12494810.1016/j.surfcoat.2019.124948 ↗
54. Saravanan I, ElayaPerumal A, Vettivel SC, Selvakumar N, Baradeswaran A (2015) optimizing wear behavior of TiN coated SS 316L against Ti alloy using Response Surface Methodology. Mater Design 67:469–48210.1016/j.matdes.2014.10.051 ↗
55. Zhou J, Ma K, Li CX, Yasir M, Luo XT, Li CJ (2020) Microstructures of aluminum surfacesreinforced with 316L stainless steel particles via high-speed particle injection and the resulting double strengthening mechanism. Surf Coatings Technol 385:12538010.1016/j.surfcoat.2020.125380 ↗
56. Linda A, Akram A, Abdelhak A, Corinne N, Elia Z, Ahlam B, Mourad Z, Régis B (2021) Relationship between structure, surface topography and tribo-mechanical behavior of Ti-N thin films elaborated at different N2 flow rates. Thin Solid Films 724:138598. https://doi.org/10.1016/j.tsf.2021.13859810.1016/j.tsf.2021.138598 ↗
57. Aissani L, Alhussein A, Belgroune A, Nouveau C, Zgheib E, Barille R, Montagne A (2021) Effect of carbon content on structural, mechanical and tribological properties of Cr-V-C-N coatings. Thin Solid Films 732:13878210.1016/j.tsf.2021.138782 ↗
58. Uysal M, Algül H, Duru E, Kahraman Y, Alp A, Akbulut H (2021) Tribological properties of Ni–W–TiO2–GO composites produced by ultrasonically–assisted pulse electro co–deposition. Surf Coatings Technol 410:12694210.1016/j.surfcoat.2021.126942 ↗
59. Li Q, Song P, Ji Q, Huang Y, Lia D, Zhaia R, Zhenga B, Lu J (2019) Microstructure and wear performance of arc-sprayed Al/316L stainless-steel composite coating. Surf Coat Technol 374:189–20010.1016/j.surfcoat.2019.06.006 ↗
60. Doğan F, Uysal M, Duru E, Akbulut H, Aslan S (2021) Pulsed electrodeposition of Ni-B/TiN composites: effect of current density on the structure, mechanical, tribological, and corrosion properties. Journal of Asian ceramic societies 8:1271–128410.1080/21870764.2020.1840704 ↗
61. Li Q, Luo H, Song P, Zang J, Zhou H (2017) Friction and wear properties of 316L stainless steel/aluminum composite coating. Heat Treat Met 42:6–12
62. Ürdem Ş, Duru E, Algül H, Uysal M, Akbulut H (2021) Evaluation of high temperature tribological behavior of electroless deposited NiB–Al2O3 coating. Wear 482–483:20396010.1016/j.wear.2021.203960 ↗
63. Kato H (2008) Effects of supply of fine oxide particles onto rubbing steel surfaces on severe–mild wear transition and oxide film formation. Tribol Int 41:735–74210.1016/j.triboint.2008.01.001 ↗