Micromechanical evaluation of DP1000-GI dual-phase high-strength steel resistance spot weld
Source abstract
Abstract
In situ micro-cantilever bending tests were carried out on resistance spot welded DP1000-GI dual-phase high-strength steel in order to derive the mechanical response of the welds. Notched micro-cantilevers were milled using focused ion beam milling at the base metal, inter-critical, fine-grained and coarse-grained heat affected zones, and fusion zone. It was shown that due to large plastic yielding, linear-elastic fracture mechanics are inapplicable. To evaluate the fracture toughness of different weld zones, cyclic loading was applied to track the crack size and the conditional fracture toughness of weld zones was measured using crack tip opening displacement and J -integral methods. It was found that micro-cantilever bending method provides insight to the fracture toughness and local mechanical response of different weld zones. The results obtained can be used to make an accurate correlation between resistance spot welding process, microstructure and mechanical response of DP1000-GI dual-phase high-strength steel welds.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Metal and Thin Film Mechanics · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Pouranvari M (2012) Susceptibility to interfacial failure mode in similar and dissimilar resistance spot welds of DP600 dual phase steel and low carbon steel during cross-tension and tensile-shear loading conditions. Mater Sci Eng A 546:129–13810.1016/j.msea.2012.03.040 ↗
2. Dancette S, Massardier-Jourdan V, Fabrègue D, Merlin J, Dupuy T, Bouzekri M (2011) HAZ microstructures and local mechanical properties of high strength steels resistance spot welds. ISIJ Int 51:99–10710.2355/isijinternational.51.99 ↗
3. Smith RA (1980) Sizing of spot welds by elastic/plastic analysis. In: 3th European colloquium on fracture, Oxford, pp 49–5610.1016/B978-0-08-026161-4.50160-6 ↗
4. Chao YJ (2003) Failure mode of spot welds: interfacial versus pullout. Sci Technol Weld Join 8:133–137
5. Pouranvari M, Marashi SPH (2011) Failure mode transition in AHSS resistance spot welds. Part I. Controlling factors. Mater Sci Eng A 528:8337–834310.1016/j.msea.2011.08.017 ↗
6. Furusako S, Watanabe F, Murayama G, Hamatani H, Oikawa H, Takahashi Y, Nose T (2013) Current problems and the answer techniques in welding technique of auto bodies. Nippon Steel Tech Rep 1995:25–31
7. Pouranvari M (2017) Fracture toughness of martensitic stainless steel resistance spot welds. Mater Sci Eng A 680:97–10710.1016/j.msea.2016.10.088 ↗
8. Tong W, Tao H, Zhang H, Jiang X, Marya MP, Hector LG, Gayden XQ (2005) Deformation and fracture of miniature tensile bars with resistance-spot-weld microstructures. Metall Mater Trans A 36:2651–266910.1007/s11661-005-0263-4 ↗
9. Baltazar Hernandez VH, Panda SK, Okita Y, Zhou NY (2010) A study on heat affected zone softening in resistance spot welded dual phase steel by nanoindentation. J Mater Sci 45:1638–1647. https://doi.org/10.1007/s10853-009-4141-010.1007/s10853-009-4141-0 ↗
10. Iqbal F, Ast J, Göken M, Durst K (2012) In situ micro-cantilever tests to study fracture properties of NiAl single crystals. Acta Mater 60:1193–120010.1016/j.actamat.2011.10.060 ↗
11. Di Maio D, Roberts SG (2005) Measuring fracture toughness of coatings using focused-ion-beam-machined microbeams. J Mater Res 20:299–30210.1557/JMR.2005.0048 ↗
12. McCarthy J, Pei Z, Becker M, Atteridge D (2000) FIB micromachined submicron thickness cantilevers for the study of thin film properties. Thin Solid Films 358:146–15110.1016/S0040-6090(99)00680-X ↗
13. Camposilvan E, Torrents O, Anglada M (2014) Small-scale mechanical behavior of zirconia. Acta Mater 80:239–24910.1016/j.actamat.2014.07.053 ↗
14. Wurster S, Motz C, Pippan R (2012) Characterization of the fracture toughness of micro-sized tungsten single crystal notched specimens. Philos Mag 92:1803–182510.1080/14786435.2012.658449 ↗
15. Costin WL, Lavigne O, Kotousov A (2016) A study on the relationship between microstructure and mechanical properties of acicular ferrite and upper bainite. Mater Sci Eng A 663:193–20310.1016/j.msea.2016.03.103 ↗
16. Chabok A, Van der Aa E, De Hosson JTM, Pei YT (2017) Mechanical behavior and failure mechanism of resistance spot welded DP1000 dual phase steel. Mater Des 124:171–18210.1016/j.matdes.2017.03.070 ↗
17. STAHL-EISEN-Prüfblätter des Stahlinstituts VDEh (2008) Testing and documentation guideline for the joinability of steel sheet part 2: resistance spot welding
18. Dao M, Chollacoop N, Van Vliet KJ, Venkatesh TA, Suresh S (2001) Computational modeling of the forward and reverse problems in instrumented sharp indentation. Acta Mater 49:3899–391810.1016/S1359-6454(01)00295-6 ↗
19. Evans AG, Charles EA (1976) Fracture toughness determinations by indentation. J Am Ceram Soc 59:371–37210.1111/j.1151-2916.1976.tb10991.x ↗
20. ASTM (1997) Standard test method for plane-strain fracture toughness of metallic materials. ASTM International, West Conshohocken, pp 90–399
21. ASTM (2001) Standard test method for measurement of fracture toughness. ASTM International, West Conshohocken, pp 1820–1901
22. Shih CF (1981) Relationships between the J-integral and the crack opening displacement for stationary and extending cracks. J Mech Phys Solids 29:305–32610.1016/0022-5096(81)90003-X ↗
23. Ast J, Przybilla T, Maier V, Durst K, Göken M (2014) Microcantilever bending experiments in NiAl—evaluation, size effects, and crack tip plasticity. J Mater Res 29:2129–214010.1557/jmr.2014.240 ↗
24. Wei Y, Hutchinson JW (1997) Steady-state crack growth and work of fracture for solids characterized by strain gradient plasticity. J Mech Phys Solids 45:1253–127310.1016/S0022-5096(97)00018-5 ↗
25. Demir E, Raabe D, Roters F (2010) The mechanical size effect as a mean-field breakdown phenomenon: example of microscale single crystal beam bending. Acta Mater 58:1876–188610.1016/j.actamat.2009.11.031 ↗
26. Wang C, Wang M, Shi J, Hui W, Dong H (2008) Effect of microstructural refinement on the toughness of low carbon martensitic steel. Scripta Mater 58:492–49510.1016/j.scriptamat.2007.10.053 ↗
27. Zhang C, Wang Q, Ren J, Li R, Wang M, Zhang F, Sun K (2012) Effect of martensitic morphology on mechanical properties of an as-quenched and tempered 25CrMo48V steel. Mater Sci Eng A 534:339–34610.1016/j.msea.2011.11.078 ↗
28. Zhou T, Yu H, Wang S (2016) Effect of microstructural types on toughness and microstructural optimization of ultra-heavy steel plate: EBSD analysis and microscopic fracture mechanism. Mater Sci Eng A 658:150–15810.1016/j.msea.2016.02.001 ↗
29. Cha BW, Na SJ (2003) A study on the relationship between welding conditions and residual stress of resistance spot welded 304-type stainless steels. J Manuf Syst 22:181–18910.1016/S0278-6125(03)90019-7 ↗