Effect of recrystallisation on Al3Zr dispersoid behaviour in thick plates of aluminium alloy AA7150
Source abstract
Abstract
The ageing responses of surface/centre layer materials from a commercially produced AA7150 thick plate have been studied after both water quenching (WQ) and air cooling (AC). The results show that the higher degree of recrystallisation near the plate surface decreases its age hardening response in AC condition. Quench-induced phases have been found to precipitate preferentially on Al3Zr dispersoids in recrystallised grains. Microstructural observations show that Al3Zr dispersoids in recrystallised grains exhibit the same crystal structure and orientation as those in adjacent subgrains.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. Polmear IJ (2006) Light alloys/metallurgy of the light metals, 4th edn. Pergamon press, Melbourne
2. Zieliński A et al (2002) Influence of retrogression and reaging (RRA) heat treatment on microstructure, mechanical and chemical behaviour of an Al–Zn–Mg alloy. Adv Mater Sci 2(1):33–41
3. Robinson JS (2000) Influence of retrogressing and reaging on the stress corrosion cracking resistance of 7010 in 7th International conference on aluminium alloys, Charlottesville, VA, USA10.4028/www.scientific.net/MSF.331-337.1653 ↗
4. Xu DK, Rometsch PA, Birbilis N (2012) Improved solution treatment for an as-rolled Al-Zn-Mg-Cu alloy. Part II. Microstructure and mechanical properties. Mater Sci Eng A 534:244–25210.1016/j.msea.2011.11.073 ↗
5. Zhang X et al (2011) Effect of Processing Parameters on Quench Sensitivity of an AA7050 sheet. Mater Sci Eng A 528:795–80210.1016/j.msea.2010.07.033 ↗
6. Suzuki H, Kanno M, Saitoh H (1984) The Effect of Zr or Cr Addition on the Recrystallization Behavior of Al-Zn-Mg-Cu Alloys. J Japan Inst Light Met 34(11):630–63610.2464/jilm.34.630 ↗
7. Park JK, Ardell AJ (1983) Microstructures of the Commercial 7075 AI Alloy in the T651 and T7 Tempers. Metall Trans A 14A:1957–196510.1007/BF02662363 ↗
8. Liu S et al (2010) Investigation of Quench Sensitivity of High Strength Al-Zn-Mg-Cu alloys by time-temperature-properties Diagrams. Mater Des 31:3116–312010.1016/j.matdes.2009.12.038 ↗
9. Fridlyander IN (2001) Aluminum Alloys in Aircraft in the periods of 1970-2000 and 2001-2015. Met Sci Heat Treat 43(1–2):6–1010.1023/A:1010453702596 ↗
10. Liu. J (2006) Advanced aluminum and hybrid aerostructures for future aircraft. Mater Sci Forum 519-521:1233–123810.4028/www.scientific.net/MSF.519-521.1233 ↗
11. Starke EA, Staley JT (1996) Application of modern aluminum alloys to aircraft. Prog Aerosp Sci 32:131–17210.1016/0376-0421(95)00004-6 ↗
12. Robson JD, Prangnell PB (2001) Dispersoid precipitation and process modelling in zirconium contaning commercial aluminium alloys. Acta Mater 49:599–61310.1016/S1359-6454(00)00351-7 ↗
13. Deschamps A et al (2009) Influence of cooling rate on the precipitation microstructure in a medium strength Al-Zn-Mg alloy. Mater Sci Eng A 501:133–13910.1016/j.msea.2008.09.067 ↗
14. Schöbel M, Pongratz P, Degischer HP (2012) Coherency loss of Al3(Sc, Zr) precipitates by deformation of an Al–Zn–Mg alloy. Acta Mater 60(10):4247–425410.1016/j.actamat.2012.04.011 ↗
15. Robson JD (2004) Microstructural Evolution in Aluminium alloy 7050 during Processing. Mater Sci Eng A 382:112–12110.1016/j.msea.2004.05.006 ↗
16. Kanno M, Ou B-L (1991) Heterogeneous Precipitation of Intermediate Phases on Al3Zr Particles in Al-Cu-Zr and Al-Li-Cu-Zr Alloys. Mater Trans 32(5):445–45010.2320/matertrans1989.32.445 ↗
17. Nes E (1972) Precipitation of the Metastable Cubic Al3Zr-phase in Subperitectic Al-Zr Alloys. Acta Mater 20(4):499–50610.1016/0001-6160(72)90005-3 ↗
18. Sigli C (2004) Zirconium solubility in aluminum alloys. Mater Forum 28:1353–1358
19. Thompson DS, Subramanya BS, Levy SA (1970) Quench Rate Effects in AI-Zn-Mg-Cu Alloys. Metall Trans 2:1149–115010.1007/BF02664247 ↗
20. Ryum N (1968) Precipitation and recrystallization in an Al-0.5 wt% Zr-Alloy. Acta Mater 17:269–27810.1016/0001-6160(69)90067-4 ↗
21. Robson JD (2004) A new model for prediction of dispersoid precipitation in aluminium alloys containing zirconium and scandium. Acta Mater 52:1409–142110.1016/j.actamat.2003.11.023 ↗
22. Xu DK, Rometsch PA, Birbilis N (2012) Improved solution treatment for an as-rolled Al-Zn-Mg-Cu alloy. Part I. characterisation of constituent particles and overheating. Mater Sci Eng A 534:234–24310.1016/j.msea.2011.11.065 ↗
23. Zhang Y, Rometsch PA, Muddle BC (2011) Characterisation and control of Al3Zr dispersoids in Al-Zn-Mg-Cu-Zr alloys in European conference on aluminium alloys, DGM, Bremen, Germany