The fracture toughness of bast fibre reinforced polyester composites Part 1 Evaluation and analysis
Source abstract
Abstract
Hemp and jute fibre reinforced polyester composites were fabricated to various fibre volume fractions (Vf) up to 0.45. Laminates reinforced with a chopped strand mat (CSM) glass fibre were also manufactured. The tensile properties of these materials were evaluated. Fracture toughness was assessed, using linear elastic fracture mechanics (LEFM) principles, under quasi-static loading conditions. At equivalent Vf (0.2) it was found that the fracture toughness (KIc) of the CSM glass fibre reinforced material was approximately 3 times greater than that of the natural fibre reinforced laminates and an order of magnitude greater than the unreinforced polymer alone. Critical strain energy release rates (Gc) and plastic zone radii were computed. The Gc of the natural fibre reinforced laminates was approximately an order of magnitude lower than that of the CSM reinforced material at the same Vf. It was hypothesised that the size of the crack-tip plastic zone influences the energy absorbing capacity of the material. By comparing the relative volumes of the plastic zones, implications regarding the toughening mechanisms operative in natural fibre reinforced composites have been made. The applicability of LEFM to characterise toughness in these materials is discussed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Natural Fiber Reinforced Composites · Mechanical Behavior of Composites · Structural Response to Dynamic Loads
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. J. E. GORDON, in “The New Science of Strong Materials” (Penguin Books, London, 1976) p. 135.
2. P. J. ROE and M. P. ANSELL, J. Mater. Sci. 20 (1985) 4015.10.1007/BF00552393 ↗
3. B. HARRIS, in “ENGINEERING COMPOSITE MATERIALS” (Inst. of Metals, London, 1980).
4. A. R. SANADI, S. V. PRASAD and P. K. ROHATGI, J. Mater. Sci. 21 (1986) 4299.10.1007/BF01106545 ↗
5. S. V. PRASAD, C. PAVITHRAN and P. K. ROHATGI, ibid. 18 (1983) 1443.10.1007/BF01111964 ↗
6. N. M. WHITE and M. P. ANSELL, J. Mat. Sci. 18 (1983) 1549.10.1007/BF01111977 ↗
7. J. L. O'DELL, in Proceedings of the 4th International Conference onWoodfiber-Plastic Composites, Madison, May 1997 (Forest Products Society, Madison, 1997) p. 280.
8. M. HUGHES, L. MOTT, J. HAGUE and C. A. S. HILL, in Proceedings of the 5th International Conference on Woodfiber-Plastic Composites, Madison, May 1999 (Forest Products Society, Madison, 1999) p. 175.
9. G. SEBE, N. S. CETIN, C. A. S. HILL and M. HUGHES, App. Comp. Mat. 7 (2000) 341.10.1023/A:1026538107200 ↗
10. M. HUGHES, Ph.D. thesis, University of Wales, Bangor, 2000.
11. D. HULL and T. W. CLYNE, in “An Introduction to Composite Materials” (Cambridge University Press, Cambridge, 1996).10.1017/CBO9781139170130 ↗
12. J. MARTIN, in “Materials for Engineering” (Inst. of Materials, London, 1996).
13. J. F. KNOTT, in “Fundamentals of Fracture Mechanics” (Butterworths, London, 1973).
14. V. Z. PARTON, in “Fracture Mechanics: From Theory to Practice” (Gordon and Breach, Philadelphia, 1992).
15. BS 7448: Part 1. (British Standards Institution, London, 1991).
16. ASTM. Designation: E 399–90. (ASTM, Philadelphia, 1991).
17. M. PATTON-MALLORY and S. M. CRAMER, Forest Products Journal 37(7/8) (1987) 39.
18. J. G. WILLIAMS, Phil. Trans. R. Soc. Lond. A 299 (1981) 59.10.1098/rsta.1981.0009 ↗
19. S. E. STANZL-TSCHEGG, E. K. TSCHEGG and A. TEISCHINGER, Wood and Fiber Science 26(4) (1994) 467.
20. S. E. STANZL-TSCHEGG, D. M. TAN and E. K. TSCHEGG, Wood Sci. Technol. 29 (1995) 31.10.1021/es00001a753 ↗
21. Idem., Mokuzai Gakkaishi 42(7) (1996) 642.
22. P. W. LUCAS, M. F. CHOONG, H. T. TAN, I. M. TURNER and A. J. BERRICK, Phil. Trans. R. Soc. Lond. B 334 (1991) 95.10.1098/rstb.1991.0099 ↗
23. P. W. LUCAS, B. W. DARVELL, K. D. LEE, T. D. B. YUEN and M. F. CHOONG, ibid. 348 (1995) 363.10.1098/rstb.1995.0074 ↗
24. P. W. LUCAS, H. T. W. TAN and P. Y. CHENG, ibid. 352 (1997) 342.10.1098/rstb.1997.0025 ↗
25. T. L. ANDERSON, in “Fracture Mechanics: Fundamentals and Applications, ” 2nd ed. (CRC Press, Boca Raton, FL, 1995).
26. BS 2782: Part 10: Method 1003: (1977) EN 61 (British Standards Institution, London, 1977).
27. F. L. MATTHEWS and R. D. RAWLINGS, in “Composite Materials: Engineering and Science” (Chapman and Hall, London, 1994).
28. M. F. ASHBY and D. R. H. JONES, in “Engineering Materials: An Introduction to Their Properties and Applications” (Pergamon Press, Oxford, 1980).
29. J. IVENS, H. BOS and I. VERPOEST, in “Renewable Biproducts: Industrial Outlets and Research for the 21st Century, ” edited by International Agricultural Center (IAC,Wageningen, The Netherlands, 1997).