Interfacial microstructure and dynamic compressive behavior of explosively welded TA2/AZ31B/7075Al multilayer composites
Source abstract
Abstract
Lightweight Ti/Mg/Al multilayer composites have considerable application potential in aerospace and protective structures. However, their overall performance strongly depends on the bonding quality and microstructural evolution of heterogeneous interfaces. In this study, TA2/AZ31B/7075Al composite plates containing with 1060Al interlayers were fabricated by explosive welding, and their interfacial morphology, elemental distribution, crystallographic characteristics, and static and dynamic compression behaviors were systematically investigated. The TA2/1060Al and 1060Al/7075Al interfaces exhibited nearly flat bonding morphologies without obvious defects, whereas the two Al/Mg interfaces showed typical wavy structures. The wavelength and amplitude of the upper 1060Al/AZ31B interface were approximately 300 μm and 67 μm, respectively, which were significantly larger than those of the lower AZ31B/1060Al interface. Distinct microstructural evolution characteristics were observed near different interfaces, including {10-12} twinning on the TA2 side, grain refinement and recrystallization on the 1060Al side, and the formation of continuous Mg 17 Al 12 intermetallic compound layers at the two Al/Mg interfaces. The 7075Al side near 1060Al/7075Al showed more pronounced deformation substructures and higher local misorientation. Under static compression, the maximum compressive strengths of the parallel and series configuration specimens were 514 MPa and 346 MPa, respectively. Under dynamic compression, these values increased to 585 MPa and 382 MPa, respectively. The failure behavior of the composite plates was mainly controlled by shear fracture of the AZ31B layer and delamination at the Al/Mg interfaces, which became more pronounced under high-strain-rate loading. These findings provide guidance for the interfacial design of lightweight Ti/Mg/Al laminated functionally graded composites to a certain extent.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Intermetallics and Advanced Alloy Properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. A review on lightweight materials for defence applications: present and future developments10.1016/j.dt.2023.02.025 ↗
2. Development and applications of aluminum alloys for aerospace industry10.1016/j.jmrt.2023.09.274 ↗
3. Experimental and numerical studies of fiber metal laminates comprising ballistic fabrics subjected to shock impact10.1016/j.compstruct.2022.115917 ↗
4. Preparation, structure and properties of Mg/Al laminated metal composites fabricated by roll-bonding, a review10.1016/j.jma.2022.08.001 ↗
5. Effect of thermal oxidation on corrosion resistance of commercially pure titanium in acid medium10.1007/s11665-011-9970-8 ↗
6. A review on electromagnetic shielding magnesium alloys10.1016/j.jma.2021.10.001 ↗
7. Evolution of precipitate microstructures during the retrogression and re-ageing heat treatment of an Al–Zn–Mg–Cu alloy10.1016/j.actamat.2010.05.017 ↗
8. Friction stir lap joining aluminum and magnesium alloys10.1016/j.scriptamat.2007.10.033 ↗
9. Recent developments in explosive welding10.1016/j.matdes.2010.10.017 ↗
10. Microstructure evolution and mechanical properties of an AA6061/AZ31B alloy plate fabricated by explosive welding10.1016/j.jallcom.2017.11.285 ↗
11. Effect of bonding time on the interfacial microstructure and mechanical properties of diffusion bonded tungsten alloy/steel joints using CrFeCoNiCu high entropy alloy interlayer10.1016/j.jmrt.2024.11.243 ↗
12. Al-to-Mg friction stir welding: effect of material position, travel speed, and rotation speed10.1007/s11661-010-0340-1 ↗
13. Multi-scale simulation and microstructure characteristics of TC4 ELI/Al 6013 plates by explosive welding10.1016/j.jmapro.2024.07.014 ↗
14. Research progress in numerical simulation of explosive welding
15. Microstructure and properties of magnesium AZ31B–aluminum 7075 explosively welded composite plate10.1016/j.msea.2009.12.007 ↗
16. Structural properties of Ti/Al clads manufactured by explosive welding and annealing10.1016/j.matdes.2015.11.087 ↗
17. Microstructure and mechanical properties of Ti/Al explosive cladding10.1016/j.matdes.2013.12.012 ↗
18. Numerical simulation on interface waves variation in explosive welding
19. Investigation of interfacial structure and dynamic mechanical behavior of titanium alloy laminated composites10.1016/j.jmrt.2022.11.101 ↗
20. Dynamic compression behavior of multilayered titanium matrix composites10.1016/j.matchar.2023.112698 ↗
21. Microstructure and mechanical properties of the bonding interface of explosively welded TA2/Q235 composite under dynamic shear loading10.1016/j.ijmecsci.2022.107362 ↗
22. Dynamic shear behavior and fracture characteristics of corrugated multi-interface Q245R/TA1/1060Al composite plate by explosive welding10.1016/j.engfracmech.2025.111554 ↗
23. Experimental and numerical study on ballistic impact behavior of explosively-welded double-layered Weldox700E targets against ogival-nosed projectiles10.1016/j.ijimpeng.2024.105134 ↗
24. Investigation on the explosive welding of 1100 aluminum alloy and AZ31 magnesium alloy10.1007/s11665-016-2088-2 ↗
25. High-throughput explosive welding of multimetallic coatings on Mg–Li alloys: interfacial mechanisms and performance insights10.1016/j.jmrt.2025.11.255 ↗
26. Additive manufacturing of AA2024/Al2O3 nanocomposites via friction surfacing: investigating metallurgical, mechanical, and tribological properties10.1016/j.jmrt.2025.05.124 ↗
27. Additive manufacturing of AA5083/TiN-Diamond hybrid nanocomposite parts via additive friction stir deposition: metallurgical structure, mechanical, tribological, and electrochemical properties10.1016/j.jmrt.2024.05.158 ↗
28. Shock-induced two types of {101‾2} sequential twinning in titanium10.1016/j.actamat.2018.12.017 ↗
29. Additive friction stir deposition of AA5083/MoS2-diamond hybrid nanocomposites: investigating their metallurgical, mechanical, tribological, and electrochemical characteristics, and process-structure-property relationships
30. Microstructure, corrosion, and tribological performance of multilayered cylindrical AA5083 parts fabricated by modified friction stir deposition – additive manufacturing10.1016/j.matchar.2025.114777 ↗
31. Metallurgical, mechanical, and tribological characteristics and process-structure-property relationships in the additive manufacturing of AA2024/ZrO2 nanocomposites via friction surfacing10.1016/j.cirpj.2026.01.002 ↗
32. Intermetallic compounds and mechanical properties of Mg/Al dissimilar joints by friction stir welding10.1134/S0031918X21100616 ↗
33. Improving mechanical properties of an explosive-welded magnesium/aluminum clad plate by subsequent hot-rolling10.1016/j.jallcom.2021.162957 ↗
34. Diffusion bonding of aluminum-magnesium using cold rolled copper interlayer10.1016/j.jallcom.2018.09.320 ↗
35. Biyik S, Aydin M. Effect of TiO2 content on the arc-erosion resistance of Ag/SnO2 electrical contact materials prepared via mechanical alloying-assisted powder metallurgy.
36. Effect of cubic and hexagonal boron nitride additions on the synthesis of ag–sno2 electrical contact material10.1166/jno.2019.2592 ↗
37. The influence of interface effect on the microstructure and mechanical behavior of tri-metal Ti/Al/Cu laminated metal composites10.1016/j.jmrt.2022.05.052 ↗
38. Effect of Y2O3 addition and milling time on the synthesis of nanocrystalline Ag–ZnO composite powder via mechanical alloying
39. Characterization of nanocrystalline Cu25Mo electrical contact material synthesized via ball milling10.12693/APhysPolA.132.886 ↗
40. Influence of type of process control agent on the synthesis of ag8zno composite powder10.12693/APhysPolA.135.778 ↗
41. Characterization of the microstructure, texture and mechanical properties of 7075 aluminum alloy in early stage of severe plastic deformation10.1016/j.matchar.2016.07.026 ↗
42. Coincidence site lattice boundary mechanism for the preferred growth of Goss and Cube grains during annealing in an Al-Cu-Mg alloy10.1016/j.matchar.2018.04.030 ↗
43. Deformation and fracture behaviors of AZ31B Mg alloy at elevated temperature under uniaxial compression10.1016/j.jallcom.2018.12.260 ↗
44. Interface tensile and fracture behavior of the Ti/Al3Ti metal-intermetallic laminate (MIL) composite under quasi-static and high strain rates10.1016/j.msea.2016.04.020 ↗
45. Experimental study on tensile property of AZ31B magnesium alloy at different high strain rates and temperatures10.1016/j.matdes.2013.12.031 ↗